• ETRI Journal
• /
• 제30권6호
• /
• pp.826-832
• /
• 2008

The metal-ferroelectric-metal (MFM) capacitor in the ferroelectric random access memory (FeRAM) embedded RFID chip is used in both the memory cell region and the peripheral analog and digital circuit area for capacitance parameter control. The capacitance value of the MFM capacitor is about 30 times larger than that of conventional capacitors, such as the poly-insulator-poly (PIP) capacitor and the metal-insulator-metal (MIM) capacitor. An MFM capacitor directly stacked over the analog and memory circuit region can share the layout area with the circuit region; thus, the chip size can be reduced by about 60%. The energy transformation efficiency using the MFM scheme is higher than that of the PIP scheme in RFID chips. The radio frequency operational signal properties using circuits with MFM capacitors are almost the same as or better than with PIP, MIM, and MOS capacitors. For the default value specification requirement, the default set cell is designed with an additional dummy cell.

• 한국정보통신학회논문지
• /
• 제11권12호
• /
• pp.2366-2373
• /
• 2007

본 논문에서는 $0.18{\mu}m$의 EEPROM cell을 사용하여 수동형 UHF RFID 태그 칩에 사용되는 저전력, 저면적의 1Kbits 비동기식 EEPROM IP를 설계하였다. 저면적 회로 설계 기술로는 $0.18{\mu}m$ EEPROM 공정을 이용하여 비동기식 EEPROM IP를 설계하므로 command buffer와 address buffer를 제거하였고 separate I/O 방식을 사용하므로 tri-state 데이터 출력 버퍼(data output buffer)를 제거하였다. 그리고 저전압(low voltage)의 VDD에서 EEPROM cell이 필요로 하는 고전압(high voltage)인 VPP와 VPPL 전압을 안정적으로 공급하기 위해 기존의 PN 접합 다이오드 대신 Schottky 다이오드를 사용한 Dickson 전하펌프를 설계하므로 전하펌프의 펌핑단(pumping stage)의 수를 줄여 전하펌프가 차지하는 면적을 줄였다. 저전력 회로 설계 기술로 Dickson 전하 펌프(charge pump)를 이용하여 VPP generator를 만들고 Dickson 전하펌프의 임의의 노드 전압을 이용하여 프로그램과 지우기 모드에서 각각 필요로 하는 VPPL 전압을 선택하도록 하게 해주는 VPPL 전원 스위칭 회로를 제안하여 쓰기전류(write current)를 줄이므로 저전력 EEPROM IP를 구현하였다. $0.18{\mu}m$ 공정을 이용하여 설계된 비동기식 EEPROM용 테스트 칩은 제작 중에 있으며, 비동기식 1Kbits EEPROM의 레이아웃 면적은 $554.8{\times}306.9{\mu}m2$로 동기식 1Kbits EEPROM에 비해 레이아웃면적을 11% 정도 줄였다.

• Journal of Periodontal and Implant Science
• /
• 제26권1호
• /
• pp.1-26
• /
• 1996

This study was performed to estimate the effects of cultured bone cell inoculated on porous type hydroxyaptite for the regeneration of the artificial alveolar bone defect. In this experiment 3 beagle dogs were used, and each of them were divided into right and left mandible. Every surgical intervention were performed under the general anesthesia by using with intravenous injection of Pentobarbital sodium(30mg/Kg). To reduce the gingival bleeding during surgery, operative site was injected with Lidocaine hydrochloride(l:80,000 Epinephrine) as local anesthesia. After surgery experimental animal were feeded with soft dietl Mighty dog, Frisies Co., U.S.A.) for 1 weeks to avoid irritaion to soft tissue by food. 2 months before surgery both side of mandibular 1st premolar were extracted and bone chips from mandibular body were obtained from all animals. Bone cells were cultured from bone chips obtained from mandible with Dulbecco's Modified Essential Medium contained with 10% Fetal Bovine Serum under the conventional conditions. Porous type hydroxyapatite were immerse into the high concentrated cell suspension solution, and put 4 hours for attachin the cells on the surface of hydroxyapatite. Graft material were inserted on the artificial bone defect after 3 days of culture. Before insertion of cellinoculated graft material, scanning electronic microscopic observation were performed to confirm the attachment and spreading of cell on the hydroxyapatite surface. 3 artificial bone defects were made with bone trephine drill on the both side of mandible of the experimental animal. First defect was designed without insertion of graft material as negative control, second was filled with porous replamineform hydroxyapatite inoculated with cultured bone marrow cells as expermiental site, and third was filled with graft materials only as positive control. The size of every artificial bone defect was 3mm in diameter and 3mm in depth. After the every surgical intervention of animals, oral hygiene program were performed with 1.0% chlorhexidine digluconate. All of the animals were sacrificed at 2, 4, 6 weeks after surgery. For obtaining histological section, tissus were fixed in 10% Buffered formalin and decalcified with Planko - Rycho Solution for 72hr. Tissue embeding was performed in paraffin and cut parallel to the surface of mandibular body. Section in 8um thickness of tissue was done and stained with Hematoxylin - Eosin. All the specimens were observed under the light microscopy. The following results were obtained : 1. In the case of control site which has no graft material, less inflammatory cell infiltration and rapid new bone forming tendency were revealed compared with experimental groups. But bone surface were observed depression pattern on defect area because of soft tissue invasion into the artificial bone defect during the experimental period. 2. In the porous hydroxyapatite only group, inflammatory cell infiltration was prominet and dense connective tissue were encapsulated around grafted materials. osteoblastic activity in the early stage after surgery was low to compared with grafted with bone cells. 3. In the case of porous hydroxyapatite inoculated with bone cell, less inflammatory cell infiltration and rapid new bone formation activity was revealed than hydroxyapatite only group. Active new bone formation were observed in the early stage of control group. 4. The origin of new bone forming was revealed not from the center of defected area but from the surface of preexisting bony wall on every specimen. 5. In this experiment, osteoclastic cell was not found around grafted materials, and fibrovascular invasion into regions with no noticeable foreign body reaction. Conclusively, the cultured bone cell inoculated onto the porous hydroxyapatite may have an important role of regeneration of artificial bone defects of alveolar bone.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• 제17권4호
• /
• pp.365-378
• /
• 1995

Allogeneic bone grafting has recently been used in oral and maxillofacial regions to restore the cosmetic and functional problem. There are several types of allogeneic bone grafts ; bone powder, bone chips, bone blocks. Empirically, it is thought to be better to combine the allogeneic bone chips to any type of tissue adhesive not to displace during packing and condensing. But, there are no reports about using tissue adhesive in allogeneic bone grafting. This experimental study is designed to investigate the effect of the fibrin adhesive on bone healing process after demineralized allogeneic bone grafting in 60 rats. In control groups (30 rats), routine demineralized allogeneic bone grafting were done in 7 ${\times}$ 7mm calvarial bone defects which were drilled intentioally. And we used the fibrin adhesive for holding the bone particle in experimental groups (30 rats). Each experimental specimen was sacrified at 1, 2, 4, 6, 8 weeks postoperatively The results were as follows : 1. The degree of inflammatory cell infiltrations were more prominent in experimental than in control groups till 2 weeks. 2. Early fibroblast proliferation and new capillary proliferation were uncorporated around graft sites in the experimental groups later than in control groups at early stages. 3. Osteoblastic activity in control group was more prominent at 2 weeks. 4. Osteoblastic activity in experimental groups was more prominent than in control group till 4 weeks. 5. New bone formation was more in control group than experimental group till 3 weeks, but similar appearance after that time. As above results, initial bone healing within 2 weeks were more processed in without adhesive group than with adhesive group. But above 4 weeks; similar bone healing were observed.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2010년도 춘계학술대회
• /
• pp.788-791
• /
• 2010

본 논문에서는 인쇄공정기술로써 ETRI $0.8{\mu}m$ CMOS 공정을 사용하여 수동형 인쇄 RFID 태그칩용 64bit ROM을 설계하였다. 먼저 태그 칩의 제작단가를 줄이기 위하여 기존 실리콘 기반의 복잡한 리소그래피 공정을 사용하지 않고 게이트 단자인 폴리 층을 프린팅 기법 중 하나인 임프린트 공정을 사용하여 구현하였다. 그리고 �弼壅� ROM 셀 회로는 기존 ROM 셀 회로의 NMOS 트랜지스터대신에 CMOS 트랜스미션 게이트를 사용함으로써 별도의 BL 프리차지 회로와 BL 감지 증폭기가 필요 없이 출력 버퍼만으로 데이터를 읽어낼 수 있도록 하였다. $0.8{\mu}m$ CMOS 공정을 이용하여 설계된 8 행 ${\times}$ 8 열의 어레이를 갖는 64b ROM의 동작전류는 $9.86{\mu}A$이며 레이아웃 면적은 $311.66{\times}490.59{\mu}m^2$이다.

• 대한전자공학회논문지SD
• /
• 제42권11호
• /
• pp.41-48
• /
• 2005

미세 선 폭을 갖는 반도체 칩에서 관찰할 수 있는 crosstalk 효과는 배선 회로 사이에 존재하는 결합 커패시턴스에 의한 현상이다. 칩 전체에 대한 타이밍 분석의 정확도는 칩을 구성하는 셀과 배선에 대한 지연시간 예측 자료의 정확도에 의해서 결정된다. 본 논문에서는 결합 커패시턴스에 의한 crosstalk 효과를 반영하여 지연시간을 정확하고 효율적으로 계산할 수 있는 CMOS 셀 구동 모델과 관련 알고리즘을 제안하고 있다. 제안한 모델과 알고리즘을 지연시간 계산 프로그램에 구현하고, 칩 레이아웃에서 추출한 벤치마크회로에 대한 지연시간 예측에 적용하였다. Victim에 영향을 주는 Aggressor를 $0\~10$개까지 연결하여 각각의 경우에 대한 셀 및 배선의 지연시간을 HSPICE와 비교한 결과 $1\%$ 내외의 오차를 보이는 우수한 정확도를 확인하였다.

• 대한전자공학회논문지SD
• /
• 제44권11호
• /
• pp.109-118
• /
• 2007

SoC의 집적도와 동작 속도의 증가로 인하여 지연 고장 테스트의 중요성이 더욱 커지고 있다. 본 논문은 천이 지연 고장 테스트를 지원하는 개선된 IEEE 1500 래퍼 셀 구조와 IEEE 1149.1 TAP 제어기를 이용하기 위한 인터페이스 회로를 제시하고 이를 이용한 테스트 방법을 제안 한다. 제안 하는 셀 구조는 한 번의 테스트 명령어를 이용하여 상승 지연 고장 테스트와 하강 지연 고장 테스트를 연속적으로 수행 할 수 기능을 유지하면서 기존의 셀 구조에 비하여 적은 면적 오버헤드를 가지며 테스트 시간을 줄일 수 있다. 또한 다른 클럭으로 동작하는 코어에 대한 테스트를 동시에 수행 할 수 있다.

• 한국생물정보학회:학술대회논문집
• /
• 한국생물정보시스템생물학회 2000년도 International Symposium on Bioinformatics
• /
• pp.59-60
• /
• 2000

The past few years have seen a dramatic increase in gene expression data on the basis of DNA microarrays or DNA chips. Going beyond a generic view on the genome, microarray data are able to distinguish between gene populations in different tissues of the same organism and in different states of cells belonging to the same tissue. This affords a cell-wide view of the metabolic and regulatory processes under different conditions, building an effective basis for new diagnoses and therapies of diseases. In this talk we present machine learning techniques for effective mining of DNA microarray data. A brief introduction to the research field of machine learning from the computer science and artificial intelligence point of view is followed by a review of recently-developed learning algorithms applied to the analysis of DNA chip gene expression data. Emphasis is put on graphical models, such as Bayesian networks, latent variable models, and generative topographic mapping. Finally, we report on our own results of applying these learning methods to two important problems: the identification of cell cycle-regulated genes and the discovery of cancer classes by gene expression monitoring. The data sets are provided by the competition CAMDA-2000, the Critical Assessment of Techniques for Microarray Data Mining.

• 센서학회지
• /
• 제13권3호
• /
• pp.188-194
• /
• 2004

With a remarkable advance in CMOS (complimentary metal-oxide-semiconductor) process technology, a variety of vision sensors with signal processing circuits for complicated functions are actively being developed. Especially, as the principles of signal processing in human retina have been revealed, a series of vision chips imitating human retina have been reported. Human retina is able to detect the edge and motion of an object effectively. The edge detection among the several functions of the retina is accomplished by the cells called photoreceptor, horizontal cell and bipolar cell. We designed a CMOS vision chip by modeling cells of the retina as hardwares involved in edge and motion detection. The designed vision chip was fabricated using $0.6{\mu}m$ CMOS process and the characteristics were measured. Having reliable output characteristics, this chip can be used at the input stage for many applications, like targe tracking system, fingerprint recognition system, human-friendly robot system and etc.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2008년도 춘계학술대회 논문집
• /
• pp.247-251
• /
• 2008

This paper presents a micro air pump actuated by PZT actuator (synthetic jet actuator) for air supply for micro fuel cells. The synthetic jet actuators are usually created by a traditional PZT-driven actuator, which consists of a small cylindrical cavity, in/outlet channel and PZT diaphragms. To design the micro air pump, a numerical analysis has been conducted for flow characteristics with respect to various geometries. A prototype of the micro air pump, with a size of $mm{\times}mm{\times}mm$, was fabricated by PDMS replication process and was conducted performance test. To control the PZT actuator, we used the SP4423 micro chips that can be amplified input voltage to reduce the controller size and the power consumption. With a voltage of 3V at 100Hz, the air pump's pumping pressure is 600pa and its power consumption is only 0.1mW.