• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.12
• /
• pp.45-51
• /
• 2011

This paper presents a wideband low-noise amplifier (LNA) covering 800MHz~5.8GHz for various wireless communication standards by utilizing in a 0.13um CMOS technology. Particularly, the LNA consists of two stages to improve the low-noise characteristics, that is, a cascode input stage and an output buffer with noise cancellation technique. Also, a feedback resistor is exploited to help achieve wideband impedance matching and wide bandwidth. Measure results demonstrate the bandwidth of 811MHz~5.8GHz, the maximum gain of 11.7dB within the bandwidth, the noise figure of 2.58~5.11dB. The chip occupies the area of $0.7{\times}0.9mm^2$, including pads. DC measurements reveal the power consumption of 12mW from a single 1.2V supply.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.117-122
• /
• 2006

A CMOS LNA based on a single-stage cascode configuration is designed for MB-OFDM ultra-wide band(UWB) systems. Wideband($3.1GHz\~4.9GHz$) input matching is performed using a simple bandpass filter to minimize the chip size and the noise figure degradation. The simulation results using $0.18{\mu}m$ CMOS process parameters show a power gain of 9.7dB, a 3dB band width of $2.1GHz\~7.1GHz$, a minimum NF of 2dB, an IIP3 of -2dBm. better than -11.8dB of input matching while occupying only $0.74mm^2$ of chip area. It consumes 25.8mW from a 1.8V supply.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.9
• /
• pp.1045-1050
• /
• 2008

In this paper presents a CMOS RF receiver for IR-UWB wireless communications is presented. The impulse radio based UWB receiver adopts the non-coherent demodulation that simplifies the receiver architecture and reduces power consumption. The IR-UWB receiver consists of LNA, envelop detector, VGA, and comparator and the receiver including envelope detector, VGA, and comparator is fabricated on a single chip using $0.18{\mu}m$ CMOS technology. The measured sensitivity of IR-UWB receiver is down to -70 dBm and the BER $10^{-3}$, respectively at data rate 1 Mbps. The current consumption of IR-UWB receiver except external LNA is 5 mA at 1.8 V.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.20 no.2
• /
• pp.63-74
• /
• 2024

This Paper presents a resistive wideband fully differential low-noise amplifier (LNA) designed using a noise-cancellation technique for TV tuner applications. The front-end of the LNA employs a cascode common-gate (CG) configuration, and cross-coupled local feedback is employed between the CG and common-source (CS) stages. The moderate gain at the source of the cascode transistor in the CS stage is utilized to boost the transconductance of the cascode CG stage. This produces higher gain and lower noise figure (NF) than a conventional LNA with inductor. The NF can be further optimized by adjusting the local open-loop gain, thereby distributing the power consumption among the transistors and resistors. Finally, an optimized DC gain is obtained by designing the output resistive network. The proposed LNA, designed in SK Hynix 180 nm CMOS, exhibits improved linearity with a voltage gain of 10.7 dB, and minimum NF of 1.6-1.9 dB over a signal bandwidth of 40 MHz to 1 GHz.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2269-2275
• /
• 2008

This paper examined the simulation results after applying not only spiral inductor's 3D EM simulation but also de-embedding technique to reduce the pad's RF effects. When calculating standard deviation with measurement results not only the gain at 0.5GHz${\sim}$4GHz but also noise figure at 1.8GHz${\sim}$4GHz, the simulation results includes de-embedded inductor' model improved gain deviation by 0.171 and noise figure deviation by 0.151 than the results from simulation with foundry inductor equivalent circuit models.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.24 no.5
• /
• pp.682-685
• /
• 2020

In this paper, we analyze the dominant noise source of conventional inductively degenerated common-source (CS) cascode low noise amplifier (LNA) when width and gate length of stacked transistors vary. Analytical MOSFET and its noise model are used to estimate the contributions of noise sources. All parameters are based on measured data of 60nm, 90nm and 130nm CMOS devices. Based on the noise analysis for different frequencies and device parameters including process nodes, the dominant noise source can be analyzed to optimize noise figure on the configuration. We verified analytically that the intuctively degenerated CS topology can not sustain its benefits in noise above a certain operation frequency of LNA over different process nodes.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.5
• /
• pp.393-396
• /
• 2018

Herein, a 94-GHz low-noise amplifier (LNA) using the 65-nm CMOS process is presented. The LNA is composed of a four-stage differential common-source amplifier and impedance matching is accomplished with transformers. The fabricated LNA chip shows a peak gain of 25 dB at 94 GHz and has a 3-dB bandwidth at 5.5 GHz. The chip consumes 46 mW of DC power from a 1.2-V supply, and the total chip area, including the pads, is $0.3mm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.100-105
• /
• 2010

In this paper, a FM radio receiver integrated circuit has been developed based on $0.5{\mu}m$ CMOS process for Zero-Crossing FM demodulator over the 88MHz to 108MHz band. The receiver is designed with the low-IF architecture, and includes Low Noise Amplifier(LNA), Down-Conversion Mixer, Phase Locked Loop(PLL), IF LPF, and a comparator. The measured results of the LNA and Mixer show that the conversion gain of 23.2 dB, the input PldB of -14 dBm, and the noise figure of 15 dB. The measured analog block of the LPF and comparator show the voltage gain of over 89 dB, and the IF LPF can configure the passband from 600KHz to 1.3MHz with 100KHz step through the internal control register banks. The designed FM radio receiver operates at 4.5V with the total current consumption of 15.3mA, so the total power consumption is about 68.85mW. The commercial FM radio has been successfully received.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.10
• /
• pp.2045-2051
• /
• 2009

A 5-GHz band Low Noise Amplifier(LNA) using SOI MOSFET is designed. To improve the noise performance, depletion-type SOI MOSFET is adopted, and it is designed by the two-stage topology consisting of common-source and common-gate stages for low-voltage operation. The fabricated LNA achieved an S11 of less than -10dB, voltage gain of 21dB with a power consumption of 8.3mW at 5.5GHz, and a noise figure of 1.7dB indicated that the depletion-type LNA improved the noise figure by 0.3dB compared with conventional type. These results show the feasibility of a CMOS LNA employing depletion-type SOI MOSFET for low-noise application.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.16 no.4
• /
• pp.443-450
• /
• 2016

The linearization technique for low noise amplifier (LNA) has been implemented in standard $0.18-{\mu}m$ BiCMOS process. The MOS-BJT derivative superposition (MBDS) technique exploits a parallel LC tank in the emitter of bipolar transistor to reduce the second-order non-linear coefficient ($g_{m2}$) which limits the enhancement of linearity performance. Two feedback capacitances are used in parallel with the base-collector and gate-drain capacitances to adjust the phase of third-order non-linear coefficients of bipolar and MOS transistors to improve the linearity characteristics. The MBDS technique is also employed cascode configuration to further reduce the second-order nonlinear coefficient. The proposed LNA exhibits gain of 9.3 dB and noise figure (NF) of 2.3 dB at 2 GHz. The excellent IIP3 of 20 dBm and low-power power consumption of 5.14 mW at the power supply of 1 V are achieved. The input return loss ($S_{11}$) and output return loss ($S_{22}$) are kept below - 10 dB and -15 dB, respectively. The reverse isolation ($S_{12}$) is better than -50 dB.