• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.16 no.9
• /
• pp.855-862
• /
• 2004

This study reports pressure drops during evaporation for R-l34a, R-407C (a mixture of 23 wt% R-32, 25 wt% R-125, and 52 wt% R-l34A) and R-410A (a mixture of 50 wt% R-32 and 50 wt% R-125) in the oblong shell and Plate heat exchanger. The effects of the mass fluxes, heat fluxes, refrigerant saturation temperatures and vapor quality of refrigerants on the measured data were explored in detail. The present data showed that pressure drops of all refrigerants increase with the vapor quality. At a higher mass flux, pressure drops are higher for the entire range of the vapor quality A rise in the heat flux doesn't show significant effects on the pressure drops. Finally, at a higher saturation temperature the pressure drops are found to be lower. The pressure drops for R-407C were approximately 20% lower than those of R-l34a. R-410A had 33% lower pressure drops than R-l34a. Correlation is also provided for the measured pressure drops in terms of the friction factor.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.04a
• /
• pp.241-244
• /
• 2008

In general, RC flat plate frames have been used as a gravity load resisting system(GLRS) in building. This system should be constructed with lateral force resisting system(LFRS) such as shear walls and brace frames. When lateral loads such as earthquakes occur, LFRS undergo displacement by which connected gravity systems experience lateral displacement. Thus, flat plate system designed as GLRS should be predict unbalanced moments and punching failure due to lateral deformation. This study developed an analytical mode for predicting nonlinear behavior of RC slab column connection for the seismic performance evaluation of RC flat plate frames. For verifying the analytical model, the test results of two flat plate specimens having two continous spans with the difference gravity shear ratio($V_g/{\phi}V_c$) were compared with the results of analysis. The developed model can predict the failure modes and punching failures.

• Journal of the Korean Electrochemical Society
• /
• v.15 no.2
• /
• pp.109-114
• /
• 2012

The cathode catalyst layer in polymer electrolyte membrane fuel cells (PEMFCs) was fabricated with anodic aluminum oxide (AAO) template and its structure was characterized with scanning electron microscopy (SEM) and Brunauer-Emmett-Teller (BET) analysis. The SEM analysis showed that the catalyst layer was fabricated the Pt nanowire with uniform shape and size. The BET analysis showed that the volume of pores in range of 20-100 nm was enhanced by AAO template. The electrochemical properties with the membrane electrode assembly (MEA) were evaluated by current-voltage polarization measurements and electrochemical impedance spectroscopy. The results showed that the MEA with AAO template reduced the mass transfer resistance and improved the cell performance by approximately 25% through controlling the structure of catalyst layer.

• Resources Recycling
• /
• v.29 no.1
• /
• pp.35-42
• /
• 2020

Even asbestos-containing waste (ACW) are highly harmful to humans, it continues being produced due to the massive disposal of asbestos-containing products. A development of asbestos detoxification and recycling technologies is required. Heat treatment using microwave is the most efficient method for ACW detoxification. However, microwave heat treatment method has the limitation that asbestos does not absorb microwave at room temperature. That is why, in this study, ACW was detoxified by microwave heat treatment adding the ACW between SiC plates, which are inorganic heating elements that absorb microwaves at room temperature. In order to improove the heat transfer, ACW was crushed and pulverized and then heated using microwave. Microwave heat treatment temperature and time variables were adjusted to investigate the detoxification properties according to heat treatment conditions. After heat treatment, treated ACW was analyzed for detoxification properties through crystal structure and microstructure analysis using X-ray diffraction (XRD) and scanning electron microscopy (SEM). Microwave heat treatment method using SiC plate can be heated up to the target temperature within a short time. Finally, complete asbestos detoxification was confirmed from the crystal structure and the microstructure when the microwave heat treatment was performed at 1,200℃ for at over 60 minutes and at 1,300℃ for at over 10 minutes.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.186-189
• /
• 2008

The flex plate, an automotive part which mounts to the automotive engine to transfer torque to transmission, should have considerable hardness and shape accuracy. As a way to produce the flex plate, the hot press forming technology which takes advantages of high formability at elevated temperature, enhanced strength and shape stability was introduced. Therefore, as one of major process parameters the heat treatment condition should be determined to obtain appropriate hardness in the range of manufacturer's specifications. In this study, two heat treatments, austempering and quenching and tempering (QT), were compared as feasible conditions fur the hot press forming of high-carbon tool steel and the hardness and toughness after heat treatments were evaluated. The study showed that both heat treatments resulted in improved hardness but only quenching and tempering showed practicable range of toughness.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.261-266
• /
• 2000

Temperature variation during silicon wafer baking is mainly due to natural convection caused by temperature difference between silicon wafer and upper plate. Several cases are tested and calculated numerically to improve temperature uniformity. The temperature difference and velocity magnitude in the flow cell is reduced for a small gap between the wafer and upper plate because the natural convection force is suppressed in the small space. The uniform temperature distribution can be obtained with controling the incoming flow distribution from the upper plate. An alternative method is the adiabatic wall condition on the upper plate to maintain the temperature uniformity within $0.3^{\circ}C$ on the water plate.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.152-152
• /
• 2014

본 연구에서는 핫플레이트를 이용한 간단한 산화아연 박막의 열처리를 통해 역구조 유기 태양전지에서의 광전환 효율증가를 소개한다. 유기태양전지는 환경오염에 따른 신 재생에너지의 필요성이 대두되면서, 중요한 주제가 되고 있다. 본 연구에서는 3차원 물결구조의 산화아연 박막을 핫플레이트를 이용하여, $180^{\circ}C$ 에서 산화아연의 3차원 물결구조의 형성에 성공하였다. 그리고 구조적 측면 뿐만 아니라, 아연 용액에 포함된 질소로 인해 산화아연의 밴드갭이 조절되어 유기태양전지의 효율이 증가했음을 확인 하였다. 또한 본 연구의 공정을 이용하여 PET 유연기판으로의 적용이 가능하다는 것을 확인 하였다.

• Proceedings of the KIPE Conference
• /
• 2018.07a
• /
• pp.440-441
• /
• 2018

본 연구에서는 핫플레이트를 균일한 표면 온도로 가열시키기 위한 카트리지 히터의 설계를 시도하였다. 이를 위하여 1. 표면 전력밀도 및 전열선 전력밀도에 따른 발열온도 측정 실험 2. 카트리지 히터의 분할 영역과 전열선 권선 비율에 따른 온도 측정 실험을 실시하여 온도분포형 카트리지 히터의 설계 사양을 선정하였다. 또한 이렇게 설계한 카트리지 히터를 직접 제작하여 기존의 표준형 카트리지 히터와의 성능 비교 측정 실험을 실시하여, 본 연구에서 제시한 방법으로 제작한 카트리지 히터의 표면 온도 균일도가 우수함(표면 온도차 ${\leq}1.25[^{\circ}C]$)을 증명하였다.

• Transactions of Materials Processing
• /
• v.20 no.8
• /
• pp.588-594
• /
• 2011

A new manufacturing process is presented for automotive drive plate using a boron-containing carbon steel sheet, which is hot-formed and press quenched. Particular attention was given to the capability of the process in minimizing dimensional change.

• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.1548-1553
• /
• 2003

An experimental study of the absorption process of water vapor into a lithium bromide solution was performed. For the purpose of development of high performance absorption chiller/hater utilizing lithium bromide solution as working fluid, it is the most effective to improve the performance of absorber with the largest heat transfer area of the four heat exchangers. The experimental apparatus was composed of a plate type absorber which can increase the heat exchange area per unit volume to investigate more detail characteristics instead of the conventional type, horizontal tube bundle type. The size of plate absorbers were made for $0.4m{\times}0.6m$ and the design object of a refrigeration capacity was lRT. In this experiment, three kind plate absorbers which were flat plate, dimple plate and groove plate were used. The results were less than the design object values, that is, the refrigeration capacity was about $0.3{\sim}0.4RT$ and the overall heat transfer coefficient was $500{\sim}600kcal/m^2h^{\circ}C$ at the standard conditions.