• Korean Chemical Engineering Research
• /
• v.47 no.6
• /
• pp.705-709
• /
• 2009

Based on experimental study of lycopodium dust particles' behavior, we suggest the flame propagation model through dust clouds. With dust concentration, flame velocity reaches a maximum value at $170g/m^3$ to exceed the stoichometric concentration for lycopodium-air mixture combustion and decreases slightly in the richer side of $500g/m^3$. At $47{\sim}200g/m^3$, mean velocity of particle increases in proportion to flame velocity. As the sum of burning rate and particle velocity is approximate in flame velocity, the flame propagation velocity with lycopodium dust concentration can be estimated by the calculation and it was found that behavior of particles is useful for better understanding of dust flame propagation velocity.

• Applied Chemistry for Engineering
• /
• v.10 no.4
• /
• pp.586-591
• /
• 1999

Mixed-firing of a bituminous and an anthracite coal carried out in a batch fluidized bed combustor(0.109 m-I.D., 0.9 m-height). Effect of particle size an mixing fraction of anthracite and bituminous coal combustion characteristics were studied. The temperature profiles and pressure fluctuation properties were measured to interpret the combustion characteristics in a batch fluidized bed combustor. The used domestic anthracite coal has heating value of 2010 kcal/kg and the imported high-calorific bituminous coal has heating value of 6520 kcal/kg. The combustion characteristics in a batch fluidized bed combustor could be interpreted by using pressure fluctuation properties and temperature increasing rates. It was found that the optimum anthracite mixing percentage could be predicted analyzing the combustion rate and fluidization characteristics, The optimum mixing fraction was about 30 %. The different burning region of fluidized bed combustor was measured by temperature increasing rates.

• Journal of the Korean Institute of Gas
• /
• v.20 no.6
• /
• pp.23-30
• /
• 2016

The conventional natural gas engine realized lean combustion for the improved efficiency. However, in order to cope with exhaust gas regulations enforced gradually, the interest has shifted at the stoichiometric mixture combustion system. The stoichiometric mixture combustion method has the advantage of a three-way catalyst utilization whose purification efficiency is high, but the problem of thermal durability and the fuel economy remains as a challenge. Hydrogen-natural gas blend fuel (HCNG) can increase the rate of exhaust gas recirculation (EGR) because the hydrogen increases burning speed and lean flammability limit. The increase in the EGR rate can have a positive impact on heat resistance of the engine due to the decreased combustion temperature, and further can increase the compression ratio for efficient combustion. In this study, to minimize the exhaust emission developed HCNG engine with stoichiometric combustion method, developed three-way catalyst was applied to evaluate the conversion characteristics. The tests were carried out during the steady state and transient operating conditions, and the results were compared for both the conventional and proto-three-way catalyst of HCNG engine for city buses.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.24 no.6
• /
• pp.10-15
• /
• 2020

This study is about the changes in mechanical and combustion properties after the production of the combustion catalysts FeOOH and Fe₂O₃ having the same manufacturing method and application to the solid propellant. In order to make the FeOOH and Fe₂O₃ having the same manufacturing method, FeOOH was calcined at 200, 300, 400, 500℃ for 2 h, and the XRD results were confirmed. In addition, after applying the prepared catalyst to a solid propellant, it exhibited change in mechanical and combustion properties. As result of XRD, FeOOH was confirmed to change the crystal phase from Geothtie to Hematite between 200 and 300℃. The stress of the propellant hardly changed as the calcination temperature of the combustion catalyst incredsed, but the elongation increased when catalyst was calcined. the maximum value at 300℃. The burning rate confirmed that FeOOH without calcination was about 3~5% faster than other catalysts.

• Journal of Energy Engineering
• /
• v.18 no.4
• /
• pp.239-246
• /
• 2009

A fundamental investigation has been conducted on the combustion of single particle of a sub-bituminous coal char burning at different temperatures and residence times. The lab-scale test setup consisted of a drop tube furnace where gas temperatures varied from $900^{\circ}C$ to $1400^{\circ}C$. A calibrated two color pyrometer, mounted on the top of the furnace, provided temperature profiles of luminous particle during a char oxidation. An amount of char mass reacted during the reaction is measured with thermogravimetry analyzer by using an ash tracer method. As a result, mass and area reactivity as well as reaction rate coefficients are determined for the char burning at atmospheric pressure condition.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.6
• /
• pp.1510-1517
• /
• 1995

A theoretical method is described to simulate the propagation of turbulent premixed flames in a closed vessel. The objective is to develop and test an efficient technique to predict the propagation speed of flame as well as the geometric structure of the flame surfaces. Flame is advected by the statistically generated turbulent flow field and propagates as a wave by solving twodimensional Hamilton-Jacobi equation. In the simulation of the unburned gas flow field, following turbulence properties were satisfied: mean velocity field, turbulence intensities, spatial and temporal correlations of velocity fluctuations. It is assumed that these properties are not affected by the expansion of the burned gas region. Predictions were compared with existing experimental data for flames propagating in a closed vessel charged with hydrogen/air mixture with various turbulence intensities and Reynolds numbers. Comparisons were made in flame radius growth rate, rms flame radius fluctuations, and average perimeter and fractal dimensions of the flame boundaries. Two dimensional time dependent simulation resulted in correct trends of the measured flame data. The reasonable behavior and high efficiency proves the usefulness of this method in difficult problems of flame propagation such as in internal combustion engines.

• Applied Chemistry for Engineering
• /
• v.23 no.2
• /
• pp.169-175
• /
• 2012

In the study, the effects of $130{\sim}150^{\circ}C$ annealing condition and 1~10 wt% isopropylphenyl diphenyl phosphate (IPPP) on crystallization behavior and flame retardancy of a full name (PLA) film were determined. The crystallization kinetics of PLA films with adding 1, 5, and 10 wt% IPPP at $140^{\circ}C$ were higher than those at 130 and $150^{\circ}C$. The average crystallinity and crystallite size of PLA film with 1 wt% IPPP were 21.3% and 24.8 nm, respectively. With an increasing IPPP content, the crystallinity of PLA film increased and the crystallite size decreased. The burning rate lowered with an increasing IPPP content as well.

• Journal of the Korean Institute of Gas
• /
• v.27 no.3
• /
• pp.84-90
• /
• 2023

Oxygen, which is always present in the atmosphere among the three elements of combustion, can cause fires and explosions with only a very small amount of combustibles under high-pressure oxygen conditions. The burning rate is also significant, and can rise to temperatures that can have a direct impact, such as melting process equipment and piping in an instant. Therefore, accidents that occur under high pressure oxygen often cause more damage than other accidents. Recently, while operating a valve installed in an oxygen supply pipe, rapid combustion and rupture occurred inside, resulting in human casualties due to an explosion. In the case of an old carbon steel pipe, particles generated during operation become combustible and can cause accidents. . In particular, since oxygen facilities are facilities licensed under the High Pressure Gas Safety Management Actand there are no restrictions under the Occupational Safety and Health Act, accumulating these standards is of utmost importance. Therefore, in this study, based on accident cases and overseas standards, methods for improving safety when handling hyperbaric oxygen are reviewed.

• Journal of the Korean Institute of Gas
• /
• v.19 no.5
• /
• pp.75-80
• /
• 2015

Aluminum dusts, from micro to nano-scale, are widely used in various applications such as propulsion and pyrotechnic compounds because of high burning rate. In this study, the pyrolysis hazard of aluminum dusts with different median size (sized by 70 nm, 100 nm, $6{\mu}m$, $15{\mu}m$) were investigated experimentally. The thermal decomposition characteristics of aluminum dusts with the variation of heating rate were investigated using TGA (Thermo gravimetric analysis) and was estimated the minimum ignition temperature from temperature of weight gain in nano and micro-sized aluminum dusts with different diameter. In the same condition of heating rate, the temperature of weight gain in aluminum dust layers increased with increasing of particle size and increased with increasing of heating rates in air. From the results, it was estimated that the pyrolysis hazard of aluminum dusts decrease with increasing of mean diameter.

• Fire Science and Engineering
• /
• v.28 no.4
• /
• pp.57-63
• /
• 2014

This study was performed to test the combustive properties of Medium Density Fibreboard (MDF) specimens treated with piperazinomethyl-bis-phosphonic acid (PIPEABP), methylpiperazinomethyl-bis-phosphonic acid (MPIPEABP), and N,N-dimethylethylenediaminomethyl-bis-phosphonic acid (MDEDAP). MDF Plates were painted in three times with 15 wt% solution of the alkylenediaminoalkyl-bis-phosphonic acids at the room temperature, respectively. After drying specimen treated with chemicals, combustive properties were examined by the cone calorimeter (ISO 5660-1). It was indicated that the specimens treated with chemicals showed the later time to peak mass loss rate ($TMLR_{peak}$) = (340475) s than that of virgin plate by reducing the burning rate. In adition, the specimens treated with chemicals showed the higher $CO_{mean}$ production (0.0883~0.0963) kg/kg than that of virgin plate. Especially, the specimens treated with chemicals showed the higher mean smoke extinction area ($SEA_{mean}$) ($5m^2/kg{\sim}21.5m^2/kg$) than that of virgin plate. Thus, It is supposed that the combustion-retardation properties were improved by the partial due to the treated alkylenediaminoalkyl-bis-phosphonic acids in the virgin MDF Plate. However, It gave a negative effect on smoke reduction.