• The Journal of the Korea Contents Association
• /
• v.6 no.4
• /
• pp.1-10
• /
• 2006

In this paper, a broadband RF module is designed and tested for 2.4GHz band applications. The RF module is composed of a low noise amplifier (LNA) with a three stage amplifier, a single ended gate mixer, matching circuits, a hairpin line band pass filter and a Chebyshev low pass filter to convert the radio frequency (RF) into the intermediate frequency (IF). The LNA has a high gain and stability, and the single ended gate mixer has a high conversion gain and wide dynamic range. In the analysis of the broadband RF module, the composite harmonic balance technique is used to analyze the operating characteristics of an RF module circuit. The RF module has a 55.2dB conversion gain with a 1.54dB low noise figure, $-120{\sim}-60dBm$ wide RF power dynamic range, -60dBm low harmonic spectrum and a good isolation factor among the RF, IF, and local oscillator (LO) ports.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.4 no.1
• /
• pp.39-45
• /
• 2011

In this paper, the design method of portable signal analysis system is proposed and the hardware module is implemented for operation of base stations based on a common platform for mobile WiMax. The new signal analysis method is implemented as two modules; a broadband RF module and a DSP based digital signal analysis module. The RF module performs the RF-IF down conversion and gain control. And the digital module measure the base staion signal. The differences of performance are insignificant in the experiment results performed through the comparison of other fixed-large system and proposed system.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.5A
• /
• pp.519-527
• /
• 2010

In this paper, we design and implement a broadband LNA(Low Noise Amplifier), a mixer, and oscillators in RF module part for radar detector. For resolving the limitation of the conventional product that the sensitivity is low due to the poor gain flatness, we propose the architecture of RF module part. The proposed RF module part is composed with a broadband 2-stage LNA, a mixer, and three oscillators, and improves the maximum gain and gain flatness for detecting various frequencies. The overall performances of RF module part are above 38 dB conversion gain in whole band and 1 dB gain flatness. These results show that the maximum gain which is the problem of the conventional product is improved 6 dB from 35 dB to 41 dB, and gain flatness is also improved 17 dB from 22 dB to 5 dB.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.11
• /
• pp.61-68
• /
• 2008

In this paper, we propose a RF front-end developments for vehicle UWB radar systems. UWB systems have a very narrow pulse width that is below 1ns. Therefore, UWB is designed to have broadband quality of low power several GHz and must coexist with the radio communication system. UWB's advantages include high channel capacity and data rate, because precise resolution for multi-path can easily position estimate and Rake receiver. Also, UWB has low interference because it displays broadband quality of low power. Positioning is made possible by short range accuracy, which can reduce the expense of system design. An RF front-end module is designed using the DCR(Direct ConveRsion) method and is composed in RF for vehicles at a low-cost.

• Journal of IKEEE
• /
• v.26 no.3
• /
• pp.456-461
• /
• 2022

In this paper, a two-stage single-ended power amplifier (PA) with broadband gain characteristics was presented by utilizing a radio frequency (RF) transformer (TF), which is essential for a differential amplifier. The bandwidth of a PA can be improved by designing TF to have broadband characteristics and then applying it to the inter-stage matching network (IMN) of a PA. For broadband gain characteristics while maintaining the performance and area of the existing PA, an IMN was implemented on an monolithic microwave integrated circuit (MMIC) and a multi-layer printed circuit board (PCB), and the simulation results were compared. As a result of simulating the PA module designed using InGaP/GaAs HBT model, it has been confirmed that the PA employing the proposed design method has an improved fractional bandwidth of 19.8% at a center frequency of 3.3GHz, while the conventional PA showed that of 11.2%.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.1 no.1
• /
• pp.8-19
• /
• 2006

The RF Module which can be adjusted for a digital terrestrial and multi standard(DVB-C, ISDB-T, DVB-H) reception is developed. The Module by single conversion does divide a broadband(45MHz~860MHz) broadcasting channels into three-bands(UHF, VHF_HIGH, VHF_LOW) to satisfy some electrical performances such as image signal rejection, phase noise, IF flatness etc and digital reception specifications such as analog and digital adjacent channel protection, co-channel protection which is important in environment with co-existence both analog and digital broadcasting systems.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.3A
• /
• pp.345-355
• /
• 2006

The RF Module which can be adjusted for a digital terrestrial and multi standard(DVB-C, ISDB-T, DVB-H) reception is developed. The Module by single conversion does divide a broadband($45MHz{\sim}860MHz$) broadcasting channels into three-bands(UHF, VHF_HIGH, VHF_LOW) to satisfy some electrical performances such as image signal rejection, phase noise, IF flatness etc and digital reception specifications such as analog and digital adjacent channel protection, co-channel protection which is important in environment with co-existence both analog and digital broadcasting systems.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.29 no.7
• /
• pp.500-507
• /
• 2018

A three-channel radio frequency (RF) monopulse receiver using a data signal with a maximum transmission rate of 274 Mbps was designed. A monopulse receiver using a broadband communication signal was designed to operate in the Ku band, and it consists of a down-conversion module and a signal-processing module. To satisfy the performance of the proposed RF monopulse receiver, a signal-processing function less than the reception sensitivity for each transmission rate according to the adaptive transmission rate is required. To minimize signal reception and mutual frequency interference of various bandwidths, two RF filters were applied. To verify the satisfaction of system requirements, an AWR Corp. simulation tool was used.

• Proceedings of the IEEK Conference
• /
• 2001.06a
• /
• pp.21-24
• /
• 2001

Bluetooth wireless technology is a publicly available specification proposed for Radio Frequency (RF) communication for short-range and point-to-multipoint voice and data transfer. It operates in the 2.4GHz ISM(Industrial, Scientific and Medical) band and offers the potential for low-cost, broadband wireless access for various mobile and portable devices at range of about 10 meters. In this paper, we describe the structure and the test results of the bluetooth baseband module we have developed. This module has a UART interface for HCI and a audio codec for voice. The interface between controller and this module supports common control interface. An FPGA implementation of this module is tested for file and bit-stream transfers between PCs.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.3
• /
• pp.98-109
• /
• 2002

Bluetooth technology is a publicly available specification proposed for Radio Frequency (RF) communication for short-range :1nd point-to-multipoint voice and data transfer. It operates in the 2.4㎓ ISM(Industrial, Scientific and Medical) band and offers the potential for low-cost, broadband wireless access for various mobile and portable devices at range of about 10 meters. In this paper, we describe the structure and the test results of the bluetooth baseband module with direct memory access method we have developed. This module consists of three blocks; link controller, UART interface, and audio CODEC. This module has a bus interface for data communication between this module and main processor and a RF interface for the transmission of bit-stream between this module and RF module. The bus interface includes DMA interface. Compared with the link controller with FIFOs, The module with DMA has a wide difference in size of module and speed of data processing. The small size module supplies lorr cost and various applications. In addition, this supports a firmware upgrade capability through UART. An FPGA and an ASIC implementation of this module, designed as soft If, are tested for file and bit-stream transfers between PCs.