• Journal of Advanced Marine Engineering and Technology
• /
• 제34권8호
• /
• pp.1084-1093
• /
• 2010

화염 전파 특성을 나타내는 G 방정식에 기초한 Sub-grid Scale연소 모델을 이용하여 보염기 주위의 난류 예혼합 연소 해석에 관한 대 와동 모사를 수행하였다. Dynamic SGS 모델이 G방정식에 도입되었으며, 삼각형의 보염기 배면의 예혼합 연소 유동에 의해 검증되었다. 해석결과는 실험결과와의 비교를 통해 속도와 온도분포를 잘 예측하고 있음을 확인하였다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권4호
• /
• pp.486-493
• /
• 2000

Flow mechanism around air flow sensor of electronic control engine, especially Karman vortex type, was investigated experimentally. The two-dimensional flow characteristics in the intermediate wake region behind a triangular vortex-generator respectively apex forward facing, apex backward facing and vertical flat plates following after apex forward facing(i.e vortex-flowmeter) were investigated at Reynolods number of $ReH=1.4\times10^4$; H is the width of a triangular vortex-generator. The vortex shedding frequency for wide Reynolds number from $7\times10^3$ to $2.1\times10^4$ was also surveyed. The velocity component was measured by X-type hot wire anemometer at 8H downstream from the bluff body. The coherent structure of the intermediate wake behind a bluff body was obtained by conditional phase average technique. As a result, it was verified that the vertical flat plates following after apex forward triangular vortex-generator make not only more linear relation between free stream velocity and vortex shedding frequency but also more periodic vortex in the vicinity of the center of wake.

• 한국추진공학회지
• /
• 제20권4호
• /
• pp.104-111
• /
• 2016

고속으로 흡입되는 공기를 산소원으로 이용하는 공기 흡입추진기관에서 해결해야 할 과제 중에 하나는 화염 안정화이다. 블라프보디와 같이 유동 감속장치를 설치하여 와류에 의한 재순환 영역을 만들어 주는 방법이 대표적인 방법이다. 최근에는 유동 벽면에 캐비티를 설치하여 화염을 안정화 시키는 것이 안정화 영역을 넓이는 효율적인 방안으로 대두되고 있는데, 캐비티에서의 유동 박리와 재접촉, 압력과 진동을 포함하여 길이와 깊이 비 등에 대한 영향 등이 조사 발표되고 있다. 그럼에도 불구하고 공기 흡입추진기관의 연구 개발과 함께, 선행 기술로서 캐비티를 이용한 화염 안정화에 대하여는 아직도 연구조사 되어야 할 과제가 많이 있다.

• Wind and Structures
• /
• 제27권6호
• /
• pp.417-430
• /
• 2018

The concentration fields in the proximities of a local gas emission source are experimentally analyzed in several combinations of wind incidences and source emissions. These conditions are determined by the plume buoyancy, emission velocity and incident flow wind speed. Concentration measurements are performed by an aspirating probe in a boundary layer wind tunnel. The analysis included the mean concentration values and the intensity of concentration fluctuations in a neutral atmospheric boundary layer flow. Different configurations are tested: an isolated stack in a homogeneous terrain and a stack with a bluff body in close proximity, located windward and leeward from the emission source. The experimental mean concentration values are contrasted with Gaussian profiles and the dilution factor is analyzed with respect to the empirical curves of the minimum dilution. Finally, a study on the plume intermittency is performed in a cross-sectional plane near the emission source. It is possible to highlight the following observations: a) plume vertical asymmetry in the case of an isolated emission source, b) significant differences in the dispersion process related to the relative location of the emission source and bluff body effects, and c) different probabilistic behavior of the concentration fluctuation data in a cross-sectional measurement plane inside the plume.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권5호
• /
• pp.573-580
• /
• 2002

Animation and time-resolved analysis of the wake characteristics of 2-D bluff body flows were examinated by applying the multi-vision PIV to square cylinders(three angles of attack: $0^{circ}, 30^{circ} and 45^{\circ}$) and circular cylinders(three rotating speeds: 0rpm, 76rpm, 153rpm) submerged within a circulating water channel $(Re=10^4)$, The macroscopic shedding patterns and their dominant frequencies were discussed in terms of instantaneous velocity, vorticity and turbulent quantities such as turbulent intensity, turbulent kinetic energy and three Reynolds stresses. Particularly the time-averaged distribution of turbulent intensity 'islands' where their peak magnitudes were focused always small regions behind the bodies without noticeable spatial migration were particularly discovered in all cases. And the dominant frequencies of the turbulent quantities in the wake regions were two times larger than those of the velocity and vorticity.

• 에너지공학
• /
• 제10권3호
• /
• pp.223-232
• /
• 2001

보염기 후류에 형성되는 화산회생의 보염특성을 고찰하기 위하여 연료 분출각의 변화, 난류발생격자의 설치, 재순환영역 내에 보조 연료의 공급에 따른 화염의 안정범위, 재순환영역의 길이 및 온도, 재순환영역주변의 난류강도 분포를 측정, 고찰하였다. 재순환영역의 길이는 주 연료 분출량의 변화에 따른 영향을 받지 않지만, 연료 분출각 및 주류유속의 변화, 보조 연료의 공급 난류발생격자의 설치 등에 따라 영향을 받는다. 확산화염의 경우 일반적으고 재순환영역의 길이가 길수록 보염성이 불량하지만, 난류발생격자를 설치한 경우에는 재순환영역의 길이가 길수록 보염성이 양호하다. 재순환영역의 온도는 연료 분출각의 변화, 보조 연료의 공급, 난류발생격사의 설치 등에 따라 영향을 받으며, 이론 혼합기 상태에서 최고값에 도달한다. 일반적으로 재순환영역의 온도가 낮을수록 보염성이 양호하지만. 난류발생격자를 설치한 경우에는 재순환영역의 온도가 낮을수록 보염성이 불량하다. 화염이 형성되는 보염기 후류 영역에 대한 난류강도는 격자의 직경이나 구속비가 큰 난류발생 격자를 설치한 경우에 크게 나타나며, 난류강도가 강 할수록 보염성이 불량하다. 연료 분출각의 변화, 난류발생격자의 설치, 재순환영역 내에 보조 연료의 공급 등의 방법으로 확산화염의 보염특성을 제어할 수 있다.

• Wind and Structures
• /
• 제17권5호
• /
• pp.515-535
• /
• 2013

The present study aims to investigate characteristics of the flow structures around the Ahmed body by using both experimental and numerical methods. Therefore, 1/4 scale Ahmed body having $25^{\circ}$ slant angle was employed. The Reynolds number based on the body height, H and the free stream velocity, U was $Re_H=1.48{\times}10^4$. Investigations were conducted in two parts. In the first part of the study, Large Eddy Simulation (LES) method was used to resolve the flow structures around the Ahmed body, numerically. In the second part of the study the particle image velocimetry (PIV) technique was used to measure instantaneous velocity fields around the Ahmed body. Time-averaged and instantaneous velocity vectors maps, streamline topology and vorticity contours of the flow fields were presented and discussed in details. Comparison of the mean and turbulent quantities of the LES results and the PIV results with the results of Lienhart et al. (2000) at different locations over the slanted surface and in the wake region of the Ahmed body were also given. Flow features such as critical points and recirculation zones in the wake region downstream of the Ahmed body were well captured. The spectra of numerically and experimentally obtained stream-wise and vertical velocity fluctuations were presented and they show good consistency with the numerical result of Minguez et al. (2008).

• 한국방재학회:학술대회논문집
• /
• 한국방재학회 2007년도 정기총회 및 학술발표대회
• /
• pp.449-453
• /
• 2007

After over a century of effort by researchers and engineers, the problem of bluff body flow, in particular vortex shedding frequency, remains almost entirely in the empirical, descriptive realm of knowledge. Computational methods have been systematically applied for vortex-induced vibrations of the cable-stayed bridge with steel composite deck by unsteady wind loadings due to vortex-shedding. The focus of this paper is to predict the vortex-induced vibration of the cable-stayed bridge with steel composite deck based computational fluid dynamics(CFD).

• Wind and Structures
• /
• 제2권4호
• /
• pp.253-266
• /
• 1999

This paper presents the effects of free-stream turbulence on streamwise surface pressure fluctuations on two-dimensional rectangular cylinders. Particular attention is given to possible effects of turbulence integral scale on fluctuation and peak pressures. The mean, standard deviation, peak pressure coefficients, spectra and cross-correlation of fluctuating pressures were measured to investigate the nature of the separation and reattachment phenomenon in turbulent flows over a wide range of turbulence intensity and integral scale.

• 한국가시화정보학회:학술대회논문집
• /
• 한국가시화정보학회 2004년도 추계학술대회 논문집
• /
• pp.5-9
• /
• 2004

An experimental study is performed turbulent swirling flow behind a crcular cylinder using 2-D PIV technique. The Reynolds number investigated is 15,000. The mean velocity vector, time mean axial velocity, turbulence intensity, kinetic energy and Reynolds shear stress behind the cylinder are measured before and behind the cylinder along the test tube.