• Animal cells and systems
• /
• v.8 no.3
• /
• pp.139-143
• /
• 2004

Two new species of the genus Psammocinia (Dictyoceratida, Irciniidae), P. conulosa n. sp. and P. ulleungensis n. sp., are described from Namhaedo Island and Ulleungdo Island, Korea. Psammocinia conulosa n. sp. seems to be close to both P. amodes Cook and Bergquist, 1998 and P. hawere Cook and Bergquist, 1996 on the basis of the skeletal structure. However, these three species are clearly separated by the following differences: Shape of P. amodes is spatulate and thin, with a broad blade narrowing to a semi-cylindrical stalk; P. hawere forms cups with a shallow excavated bowl, and attached to the substratum by a narrow base. The whole surface of the new species is very finely conulose. Psammocinia ulleungensis n. sp. is similar to P. gageoensis Sim and Lee, 2001 in shape, but this species is easily distinguished from P. gageoensis by the simple skeletal structure.

• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.2833-2838
• /
• 2007

Recently, small hydropower attracts attention because of its clean, renewable and abundant energy resources to develop. However, suitable turbine type is not determined yet in the range of small hydropower and it is necessary to study for the effective turbine type. Moreover, relatively high manufacturing cost by the complex structure of the turbine is the highest barrier for developing the small hydropower turbine. Therefore, a cross-flow turbine is adopted because of its simple structure and high possibility of applying to small hydropower. The purpose of this study is to examine the optimum configuration of nozzle shape to further optimize the cross-flow hydraulic turbine structure and to improve the performance. The results show that pressure on the runner blade in Stage 1 and velocity at nozzle outlet have close relation to the turbine performance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.7 s.250
• /
• pp.603-611
• /
• 2006

This paper presents the response surface optimization method using three-dimensional Wavier-Stokes analysis to optimize the blade shape of an axial flow fan. Reynolds-averaged Wavier-Stokes equations with $k-{\epsilon}$ turbulence model are discretized with finite volume approximations using the unstructured grid. Regression analysis is used for generating response surface, and it is validated by ANOVA and t-statistics. Four geometric variables, i.e., sweep and lean angles at mean and tip respectively were employed to improve the efficiency. The computational results are compared with experimental data and the comparisons show generally good agreements. As a main result of the optimization, the total efficiency was successfully improved. Also, detailed effects of sweep and lean on the axial flow fan are discussed.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.11a
• /
• pp.19-26
• /
• 2009

The objective of this study is to investigate aerodynamic characteristics of a Horizontal-axis wind turbines(HAWT), using CFD method with a commercial code STAR-CCM+ version 3.06. To verify the reliability of the computations, the CFD results are compared with the experimental ones of the National Renewable Energy Laboratory(NREL) Phase Ⅵ HAWT. For the comparison and examination of aerodynamic characteristics, the existent shape with a predesigned twist angle was replaced by the one with one-dimensional linear twist angle. In this study, the pressure contour and stream line around the blade were analyzed as main focus. Through this study the more efficient shape of airfoil is suggested with consideration of manufacturing cost.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.10
• /
• pp.735-741
• /
• 2007

An axial F.R.P. fan model for cooling tower is developed. The fan is designed using the equations for one dimensional inviscid flow through the fan blade. Fan shape is swept forward with a parabolic function. Calculations of the three dimensional turbulent flow around the fan are carried out to investigate performance of the fan. Data of the total pressure rise and hydraulic efficiency can be obtained for the various setting angles. Calculated values of the total pressure rise and hydraulic efficiency at the design point are less than those of the design specification. The prototype of the F.R.P. fan is made by laminating of the fiberglass and epoxy resins on the mold of fan shape.

• The KSFM Journal of Fluid Machinery
• /
• v.9 no.6 s.39
• /
• pp.9-16
• /
• 2006

Performance characteristics of an axial flow fan having distorted inlet flow have been investigated using numerical analysis as well as experiment. Two kinds of hub-cap, rounded and right-angled front shape, are tested to investigate the effect of inlet flow distortion on the fan performance. Numerical solutions are validated in comparison with experimental data measured by a five-hole probe downstream of the fan rotor. It is found from the numerical results that non-uniform axial inlet velocity profile near the hub results in the change of inlet flow angle. Large recirculation flow upstream the fan rotor for the right-angled hub-cap induces a negative incidence, thus invokes separated flow on the blade surfaces and deteriorates the performance of fan rotor.

• 한국전산유체공학회:학술대회논문집
• /
• 2003.10a
• /
• pp.230-231
• /
• 2003

Two and three-dimensional flows around a cross-flow wind turbine are investigated by the numerical simulation. The turbine studied in this paper has cylindrical shape with many small blades along its periphery. Incompressible Navier-Stokes equation is used for this simulation. A rotating coordinate system, which rotates at the same speed of the turbine, is used in order to simplify the boundary conditions on the blades of the turbine. Additionally, a boundary fitted coordinate system is employed in order to express the shape of the blades precisely. A third order upwind scheme is chosen for the approximation of the non-linear terms. When the number of blades is about 10, the highest torque is obtained.

• Proceedings of the KSME Conference
• /
• 2000.11b
• /
• pp.434-440
• /
• 2000

This study is focused on the performance prediction and design of the centrifugal pump with optimum shape. Design and analysis of centrifugal pump rely on experience of designer due to many fluid mechanical and geometrical variables. In this study, a design method was developed with experimental factors and analysed the method by comparition with 2nd-order vortex panel method. Impeller is the most important component affecting the performance of the centrifugal pump. The predicted total head for three cases, of which designs were determined by this method, agrees well with a particular commercial pump. This study shows that satisfactory performance of an optimal pump shape can be obtained through the automatic design routine.

• The KSFM Journal of Fluid Machinery
• /
• v.11 no.2
• /
• pp.46-54
• /
• 2008

This study presents a numerical optimization to optimize an axial flow fan blade to increase the efficiency. The radial basis neural network is used as an optimization method with the numerical analysis by Reynolds-averaged Navier-Stokes equations using SST model as turbulence closure. Four design variables related to airfoil maximum camber, maximum camber location, leading edge radius and trailing edge radius, respectively, are selected, and efficiency is considered as objective function which is to be maximized. Thirty designs are evaluated to get the objective function values of each design used to train the neural network. Optimum shape shows the efficiency increased by 1.0%.

• Transactions of Materials Processing
• /
• v.16 no.4 s.94
• /
• pp.288-292
• /
• 2007

This study focuses on the warm forging of a magnesium alloy impeller used for the fuel cell. The impeller has the very complicated shape with sharply twisted blade and thus is generally produced by mechanical machining or casting process. However, since these technologies give the high manufacturing cost or poor mechanical properties, the forging technology is required to make the high-quality impeller with the lower manufacturing cost. In order for production of the impeller by warm forging technology, the parametric studies using finite element analyses were carried out to find the optimal perform shape of impeller. Based on the FE simulation results, dies for impeller forging were designed and the resultant forged impeller was shown.