• International Journal of Automotive Technology
• /
• 제6권1호
• /
• pp.15-21
• /
• 2005

The purpose of this paper is to experimentally investigate the engine pollutant emissions and combustion characteristics of diesel engine fueled with ethanol-diesel blended fuel (bio-diesohol). The experiments were performed on a single-cylinder DI diesel engine. Two blend fuels were consisted of $15\%$ ethanol, $83.5\%$ diesel and $1.5\%$ solublizer (by volume) were evaluated: one without cetane improver (E15-D) and one with a cetane improver (E15-D+CN improver). The engine performance parameters and emissions including fuel consumption, exhaust temperature, lubricating oil temperature, Bosch smoke number, CO, NOx, and THC were measured, and compared to the baseline diesel fuel. In order to gain insight into the combustion characteristics of bio-diesohol blends, the engine combustion processes for blended fuels and diesel fuel were observed using an Engine Video System (AVL 513). The results showed that the brake specific fuel consumption (BSFC) increased at overall engine operating conditions, but it is worth noting that the brake thermal efficiency (BTE) increased by up to $1-2.3\%$ with two blends when compared to diesel fuel. It is found that the engine fueled with ethanol-diesel blend fuels has higher emissions of THC, lower emissions of CO, NOx, and smoke. And the results also indicated that the cetane improver has positive effects on CO and NOx emissions, but negative effect on THC emission. Based on engine combustion visualization, it is found that ignition delay increased, combustion duration and the luminosity of flame decreased for the diesohol blends. The combustion is improved when the CN improver was added to the blend fuel.

• Journal of Biosystems Engineering
• /
• 제33권5호
• /
• pp.289-295
• /
• 2008

The task of chemical spraying has been seriously considered as an irritating and annoying job for Korean rice farmers. An agricultural unmanned helicopter was suggested to solve this problem so as the farmers to have more decent farming condition. The objectives of this study were to analyze the adoptability of an experimental rotor blade (SW05) using the CFD simulation and also to compare the simulation results with experimental results. The simulation results showed that the induced power of this rotor reached to $57{\sim}63%$ of total power and the profile power was about $37{\sim}43%$ of total power. Therefore it can be concluded that this rotor's performance characteristics were not so efficient for the size of unmanned helicopter due to the low induced power and high profile power relatively compared with ones of conventional rotors. The comparison with experimental results showed that the tested lifts were less than 70% of simulated ones at the grip pitch of $12^{\circ}$ and decreased to 40% at the $18^{\circ}$ grip pitch. Therefore, it can be concluded that the rotor was too oversized to be used for a 15.4 kW (21 PS) engine.

• 동력기계공학회지
• /
• 제13권1호
• /
• pp.65-71
• /
• 2009

To address the need for new intelligent sensing, this paper introduces nano sensors made of carbon nanotube (CNT) composites and presents their preliminary experiments. Having smart material properties such as piezoresistivity, chemical and bio selectivity, the nano composite can be used as smart electrodes of the nano sensors. The nano composite sensor can detect structural deterioration, chemical contamination and bio signal by means of its impedance measurement (resistance and capacitance). For a structural application, the change of impedance shows specific patterns depending on the structural deterioration and this characteristic is available for an in-situ multi-functional sensor, which can simultaneously detect multi symptoms of the structure. This study is anticipated to develop a new nano sensor detecting multiple symptoms in structural, chemical and bio applications with simple electric circuits.

• 조명전기설비학회논문지
• /
• 제16권6호
• /
• pp.7-12
• /
• 2002

본 논문은 공동평가업체인 알파사에서 개발된 건축마감재인 바이오 액상세라믹의 물리, 화학적 특성 원적외 방사특성과 생체에의 효능을 실험을 통하여 평가한 것이다.

• 한국생물환경조절학회:학술대회논문집
• /
• 한국생물환경조절학회 2007년도 춘계 학술대회 및 정기총회
• /
• pp.178-181
• /
• 2007

• 센서학회지
• /
• 제18권1호
• /
• pp.63-71
• /
• 2009

It is said that the desirable bio-signal measurement and stimulation system should be an implantable type if the several problems such as biocompatibility, electrical safety, and so on are overcome. In addition to the biocompatibility issue, a robust RF communication and a stable electrical power source for the implantable bio-signal measurement and stimulation system are very important matters. In this paper, a wireless telemetry system which adopts the FCC's approved MICS (medical implant communication service) protocol and a wireless power transmission has been proposed. The proposed system composed of a base station (BS) and an implantable medical device (IMD) has the advantages that the interference with other RF devices can be reduced by the use of the specially assigned MICS frequency band of 402.MHz to 405 MHz. Also, the proposed system includes various functions of a multi-channel bio-signal acquisition and an electric stimulation. Since the electrical power for the IMD can be provided by the inductive link between PCB patterned coils, the IMD needs no battery so that the IMD can be smaller size and much less dangerous than the active type IMD which includes the internal battery. Finally, the validity as a wireless telemetry system has been demonstrated through the experiments by using the implemented BS and IMD.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 춘계학술대회
• /
• pp.585-588
• /
• 2007

As the distributed generation becomes more reliable and economically feasible, it is expected that a higher application of the distributed generation units would be interconnected to the existing grids. This new generation technology is linked to a large number of factors like economics and performance, safety and reliability, market regulations, environmental issues, or grid connection constrains. KEPCO (Korea Electric Power Corporation) is performing the project to develope the Distributed Micro Gas Turbine (MGT) technolgies by using Swine BIO-ENERGY. This paper describes the plans and strategies for the renewable energy of MGT on actual grid-connection under Korean situations. KEPCO also, has a research plan on bio-gas pretreatment system applicable to our domestic swine renewable resources and is performing concept design of pilot plant to test grid operation. In addition, this testing will be conducted in order to respond to a wide variety of needs for application and economic evaluation in the field of On-site generation.

• 한국수소및신에너지학회논문집
• /
• 제29권1호
• /
• pp.130-137
• /
• 2018

Now discusses the potential use and applications of coal bed methane (CBM) in various industries. One of the options for gas monetization is gas to power (GTP), sometimes called gas to wire (GTW). Electric power can be an intermediate product, such as in the case of mineral refining in which electricity is used to refine bauxite into aluminum; or it can be an end product that is distributed into a large utility power grid. For stranded gas, away from the regional markets, the integration of the ammonia and urea plants makes commercial sense. These new applications, if established, could lead to a surge in demand for methanol plants.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.260-263
• /
• 2008

KEPCO(Korea Electric Power Corporation) is performing the nation's first biogas-MGT project as an effort to encourage the utilization of wasted biogas which contains useful CH4. The goals of this project are to develop the Pretreatment system of Livestock bio-gas and set up the biogas-MGT co-generation system. The project will not only utilze flared biogas as precious energy but also improve the economics of the plant a lot. The pretreatment system mainly consists of sulfur removal tower, biogas compressor and many filtering systems. A computational fluid dynamics study in the bio gas sulfur removal tower and sulfur absorption filter was carried out. Understanding of the flow in the sulfur removal tower and sulfur adsorption filter obtained by this study can be used to identify the problems in the sulfur removal tower and to improve the sulfur removal efficiency of the sulfur removal tower. Resistance material modeling is used to simulate the sulfur adsorption filter, and the resistance coefficient was adjusted to reflect the experimental pressure loss value. And the pressure loss change with the flowrate is predicted

• 동력기계공학회지
• /
• 제16권4호
• /
• pp.5-11
• /
• 2012

There were some papers for diesel engine performance tests using BDF, but few article deals with the temperature and soot concentration of Bio diesel flame. Since the flame temperature of diesel engines is so high and change rapidly, an optical method for measurement of flame temperature is known as the most effective one. The two-color method regarding the visible wavelength radiation for the soot particles in flame was applied on Bio diesel flame in order to measure flame temperature and soot concentration in a diesel engine. Photo detecting device was newly designed and employed TSL250R, photo-diode, to pick-up the light information emitted from the combustion flame. As a result, real flame temperature T, as a flame brightness temperature, through Ta1, Ta2, were obtained and finally the characteristics of KL value as a soot concentration reveal the difference of combustion information between diesel fuel, blending oil and Bio diesel fuel oil.