• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.521-524
• /
• 2005

In order to measure ECG in daily life, a new ECG measurement method on bed was developed. The provided method does not require any direct conductive contact between the instrument and bare skin, so that it does not cause the uncomfortable feel of touch and the possible skin trouble which are typical shortcomings of the conventional conductive contact ECG measurement. The provided method utilized an array of high-input-impedance active electrodes fixed on the mattress and an indirect-skin-contact ground made of a large conductive textile sheet and laid on lower area of the mattress. A thin cotton bedcover covered the mattress, the electrodes, and the conductive textile and subjects lay on the mattress over the bedcover. ECG was obtained successfully. However its signal quality is lower and the motion artifact is larger than direct-contact measurement. Careful measurement setup was needed to reduce the motion artifact originated from variation in static electricity. From the ECG obtained by the provided method, R-peak could be discriminated easily and the information about the position and the posture of the subject could be obtained.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.9
• /
• pp.791-796
• /
• 2010

Installing noise barriers is the most common method for reducing the highway traffic noise to the road side residential area. After the report about edge potential concept of a noise barrier, various types of noise reducing devices(NRDs) called "noise reducers" have been suggested for getting more shielding effect on the top of highway noise barriers. But, it has been doubtful about effect of the NRDs in field because there was no appropriate and unified method to estimate the acoustic performance by using field measurement of the NRDs in Korea. In this study, the authors have considered to setup a practical method to test and estimate the acoustic performance of NRDs. For eliminating the noise reduction effect of the NRDs height itself, the source and measuring points are adjusted as highly as the NRDs height. For the frequency weighting in the estimation of the NRDs effect, the highway noise spectra were measured at asphalt and concrete road side and then averaged for a unit spectral parameter.

• Journal of the Institute of Convergence Signal Processing
• /
• v.24 no.3
• /
• pp.166-171
• /
• 2023

Efficient energy management is a very important factor in sensor networks with limited resources, and cluster techniques have been studied a lot in this respect. However, a problem may occur in which energy use of the cluster header is concentrated, and when the cluster header is not evenly distributed over the entire area but concentrated in a specific area, the transmission distance of the cluster members may be large or very uneven. The transmission distance can be directly related to the problem of energy consumption. Since the energy of a specific node is quickly exhausted, the lifetime of the sensor network is shortened, and the efficiency of the entire sensor network is reduced. Thus, balanced energy consumption of sensor nodes is a very important research task. In this study, factors for balanced energy consumption by cluster headers and sensor nodes are analyzed, and a balancing distribution clustering method in which cluster headers are balanced distributed throughout the sensor network is proposed. The proposed cluster method uses multi-hop routing to reduce energy consumption of sensor nodes due to long-distance transmission. Existing multi-hop cluster studies sets up a multi-hop cluster path through a two-step process of cluster setup and routing path setup, whereas the proposed method establishes a hierarchical cluster routing path in the process of selecting cluster headers to minimize the overhead of control messages.

• Proceedings of the IEEK Conference
• /
• 1998.10a
• /
• pp.799-802
• /
• 1998

As we know, gigabit ethernet is a new technology to be substituted for current fast ethernet used widely in local area network. The switch used in gigabit ethernet should deal with frames in giga-bps. To do such a fast switching, we need that serveral processes meet the budgets, such as MAC address table lookup, several giga speed path setup, fast scheduling, and etc. Especially MAC address table lookup has to be processed in the same speed with speed of incoming packets, thus the bottleneck in the process can cause packet loss by the overflow in the input buffer. We devise new practical hardware hashing method to perform fast table lookup by minimizing the number of external memory access and accelerating with hardware.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.6
• /
• pp.435-440
• /
• 2014

Contact-guided-wave tests are impractical for investigating specimens with limited accessibility and rough surfaces or complex geometric features. A non-contact setup with a laser-ultrasonic transmitter and receiver is quite attractive for guided-wave inspection. In the present work, we developed a non-contact guided-wave tomography technique using the laser-ultrasonic technique in a plate. A method for Lamb-wave generation and detection in an aluminum plate with a pulsed laser-ultrasonic transmitter and Michelson-interferometer receiver was developed. The defect shape and area in the images obtained using laser scanning, showed good agreement with the actual defect. The proposed approach can be used as a non-contact online inspection and monitoring technique.

• Journal of Institute of Convergence Technology
• /
• v.3 no.2
• /
• pp.31-37
• /
• 2013

This paper proposes a vision-based inspection algorithm for a punch which is used when forming the head of the small screws. To maintain good quality of punch, the precise inspection of its dimension and the depth of the punch head is important. A CCD camera and an illumination dome light are used to measure its dimensions. And a structured line laser is also used to measure the depth of the punch head. Resolution and visible area depend on setup between laser and camera which is determined using CAD-based simulation. The proposed method is successfully evaluated using experiment on #2 punch.

• Journal of Korean Society of Water and Wastewater
• /
• v.24 no.6
• /
• pp.691-701
• /
• 2010

As the water-cycle is transformed by increasing of the impermeable area in process of urbanization, decentralized rainwater management facilities(infiltration, harvesting and retention facilities) as source control are considered to be a method of restoring water-cycle of urban and reducing runoff. SWMM model was used to analyse the change of water-cycle structure before and after development in A new town watershed. Modified SWMM code was developed to apply infiltration facilities. The modified SWMM was used to analyse the change of water-cycle before and after infiltration trench setup in AJ subcatchment. Changes of the impervious area by development and consequent increase in runoff were analyzed. These analyses were performed by a day rainfall during ten years from 1998 to 2007. According to the results, surface runoff increased from 51.85% to 65.25 %, and total infiltration volume decreased from 34.15 % to 21.08 % in A newtown watershed. If more than 80 infiltration trenches are constructed in AJ subcatchment, the low flow and the drought flow increases by around 47%, 44%, separately. The results of this study, infiltration trench is interpreted to be an effective infiltration facility to restore water-cycle in new town.

• Journal of Coastal Disaster Prevention
• /
• v.5 no.4
• /
• pp.203-210
• /
• 2018

It is generally known that submerged breakwaters can reduce the incoming wave energy without disturbing the beach scenery. However, a submerged breakwater is also able to cause a setup of the sea level in the protected area which is also called as water piling-up. Since the piling-up can result in longshore currents, sediment transports, and unexpected beach erosion, understanding about the piling-up process is required prior to designing the nearshore structures. In this study, the water piling-up behind a submerged breakwater is assessed in the time of storm events. For the study area, Anmok beach in Gyeonso-dong, Gangwon-do is selected. 1-year, 5-year, 10-year, and 50-year return-values were derived from Peaks-Over-Threshold(POT) method and those are applied as offshore boundary conditions for the numerical simulation. The numerical results of the piling-up were assessed with regard to the wave steepness and the height of the submerged breakwater. With increase of both significant wave height and the height of the submerged breakwater, the piling-up parameter is also increased which can lead to erosion of dry beach behind the structure.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1993.04a
• /
• pp.93-100
• /
• 1993

With increasing technology, requirement to car noise and related dynamics are getting competitive keypoint. Unfortunately, vibro - acoustic behavior of a car is nowadays only possible after development of prototypes. But, obviously, in the Area of Research, many of Industrials, Universities and research centers try to codevelop the design tools to predict the vibro-acoustic behaviors. At this stage, it is more realistic to represent the existing technologies in order for the engineer to get their own know-how to design and to Integrate existing techniques, to setup their test facility, and to develope some tools with which they can successfully predict noise levels of car in the design phase. Moreover, most of the theories which will be represented in this paper can be used in the design phase. At any way, finding the cause of trouble shooting is more urgent than the design of a car to the test engineer. In this paper, transfer path analysis, noise source identification, and the key test method of modal analysis is introduced. Later, if I get the opportunity to present in KSNVE, the approach method of modal analysis is introduced. Later, if I get the opportunity to present in KSNVE, the approach method of finding characteristics of joint and welding part will be introduced. Most parts of this paper was quoted from the papers of LMS.

• Journal of Information Processing Systems
• /
• v.15 no.4
• /
• pp.820-832
• /
• 2019

Estimation of accurate blood volume flow in ultrasound Doppler blood flow spectrograms is extremely important for clinical diagnostic purposes. Blood volume flow measurements require the assessment of both the velocity distribution and the cross-sectional area of the vessel. Unfortunately, the existing volume flow estimation algorithms by ultrasound lack the velocity space distribution information in cross-sections of a vessel and have the problems of low accuracy and poor stability. In this paper, a new robust ultrasound volume flow estimation method based on multigate (RMG) is proposed and the multigate technology provides detail information on the local velocity distribution. In this method, an accurate double iterative flow velocity estimation algorithm (DIV) is used to estimate the mean velocity and it has been tested on in vivo data from carotid. The results from experiments indicate a mean standard deviation of less than 6% in flow velocities when estimated for a range of SNR levels. The RMG method is validated in a custom-designed experimental setup, Doppler phantom and imitation blood flow control system. In vitro experimental results show that the mean error of the RMG algorithm is 4.81%. Low errors in blood volume flow estimation make the prospect of using the RMG algorithm for real-time blood volume flow estimation possible.