• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.68-75
• /
• 2005

주유동 기체의 물리적 특성이 초음속 이젝터 성능에 미치는 영향에 관한 연구를 수행하였다. 기체의 분자량과 정압 비열 변화에 따른 성능 변화에 관한 연구는 축대칭 환형 분사 초음속 이젝터를 사용하였다. 주유동 기체로는 공기, $CO_{2}$, Ar, $C_{3}H_{8}$, $CCl_{2}F_{2}$를 사용하였다. 주유동 기체의 분자량과 정압 비열이 증가함에 따라 일정 주유동 압력에 대한 부유동 압력은 증가하였고 이러한 경향은 몰비열이나 비열비의 형태로 통합되어 확인되었다.

• 한국가시화정보학회지
• /
• 제9권4호
• /
• pp.47-53
• /
• 2011

A water driven ejector loop was designed and constructed for air absorption. The used ejector was horizontally installed in the loop and annular water jet at the throat entrained air through the circular pipe placed at the center of the ejector. Wide range of water flow rate was provided using two kinds of pumps in the loop. The tested range of water flow rate was 100${\ell}$ /min to 1,000 ${\ell}$/min. Two-phase flow inside the ejector loop was simulated by CFD analysis. Homogeneous particle model was used for void fraction prediction. Water and air flow rates and pressure drop through the ejector were automatically recorded by using the LabView based data acquisition system. Flow characteristics and air bubble velocity field downstream of the ejector were investigated by two-phase flow visualization and PIV measurement based on bubble shadow images. Overall performance of the two-phase ejector predicted by the CFD simulation agrees well with that of the experiment.

• 한국추진공학회지
• /
• 제9권1호
• /
• pp.61-66
• /
• 2005

혼합챔버 내에서 패브리 초킹(Fabri choking)이 발생한다는 가정을 이용하여 이차목을 갖는 환형분사 초음속 이젝터의 이론 해석을 수행하였다. 부유동 압력을 예측하기 위해 혼합챔버 입구에서 패브리 초킹면 사이를 비혼합 이론(non mixing theory)을 이용하여 계산하였다. 혼합챔버의 수축각에 의해 발생하는 깔때기 모양의 경사충격파를 이차원 경사충격파로 모사하였고, 패브리 초킹면의 주유동에만 영향을 미친다고 가정하였다. 또한 패브리 초킹면의 주유동 압력과 부유동 압력이 같다는 물리적인 제한조건을 사용하였다. 그 결과 혼합챔버의 수축각이 4도보다 작은 조건에서 실험값을 잘 예측하는 것을 확인하였다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.405-408
• /
• 2005

혼합챔버 내에서 패브리-초킹(Fabri-chocking)이 발생한다는 가정을 이용하여 이차목을 갖는 환형분사 초음속 이젝터의 이론 해석을 수행하였다. 부유동 압력을 예측하기 위해 혼합챔버 입구에서 패브리-초킹면 사이를 비혼합이론(non-mixing theory)을 이용하여 계산하였다. 혼합챔버의 수축각에 의해 발생하는 깔때기 모양의 경사충격파를 이차원 경사충격파로 모사하였고, 패브리-초킹면의 주유동에만 영향을 미친다고 가정하였다. 그 결과 혼합챔버의 수축각이 4도보다 작은 조건에서 실험값을 잘 예측하는 것을 확인하였다.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2006년도 추계 학술대회논문집
• /
• pp.185-188
• /
• 2006

An investigation of the ejector-jets focusing on its flow properties was carried out by varying the geometric parameters. The area ratio of the primary nozzle, AR that was tested in the present measurement was 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet, L/D had values of 3.41, 6.82, and 10.23. For the frame work of flow characteristics, the wall pressures distribution of ejector-jet was investigated by experiment for basic study of ejector-jet performance. In result, terminal shock location and existence of series of oblique shocks are recognized. In this study, CFD analysis was conducted at the same time. And as a result of comparison experiment data with CFD analysis, the physical phenomena of ejector-jets were estimated.

• 한국전산유체공학회지
• /
• 제12권2호
• /
• pp.46-52
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present study was 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 33 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2007년도 춘계 학술대회논문집
• /
• pp.166-170
• /
• 2007

An experimental and numerical investigation of the ejector-jets focusing on its geometric parameters that effect on thrust performance was carried out. The area ratio of the primary nozzle that was tested in the present studywas 2.17 and 3.18, while the ratio of the length to the diameter of the duct downstream the primary nozzle inlet had values of 3.41, 6.82, and 10.23. Internal flow properties of ejector-jet were estimated by comparison experiment data and CFD analysis for basic study of ejector-jet thrust performance. For examination of thrust performance, the thrust ratios increased with increase in L/D. Especially at AR=2.17, the maximum thrust augmentation was 34 percent for the shortest L/D. It is expected that the increase of mixing duct length of ejector-jet will be helpful in a thrust performance by improving mixing efficiency.

• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1673-1680
• /
• 2003

It is essential to operate chemical lasers with supersonic ejector system as the laser output power goes up. In this research, ejector design parameter study was carried out for optimal ejector design through understanding the ejector characteristics and design requirements for chemical lasers operating. Designed ejector was 3D annular type with 2$^{nd}$ -throat geometry and pressurized air was used for primary flow. Ejector design was carried out with two steps, quasi-1D gas dynamics was used for first design and commercial code was used to verify the first design. In this study, to get the effect of ejector geometry on its performance, three cases of primary nozzle area ratio and 2$^{nd}$ -throat cross sectional area and two cases of 2$^{nd}$ -throat L/D ratio experiments were carried out. Primary and secondary pressures were measured to get the mass flow rate ratio, minimum secondary pressure, ejector starting pressure and unstarting pressure at every case. In the result, better performance than design level was shown and optimal ejector design method for chemical lasers was obtained.

• 대한기계학회논문집B
• /
• 제28권10호
• /
• pp.1231-1237
• /
• 2004

Determination of geometric design parameters of a second-throat type annual supersonic ejector is described. Tested geometric parameters were primary nozzle area ratio, cross-sectional area of second-throat, L/D ratio of second-throat and primary flow injection angle. Varying these four geometric parameters, we build a test matrix made of 81 test conditions, and experimental apparatus was fabricated to accommodate them. For each test condition, the stagnation pressure of primary flow and the static pressure of the secondary flow were measured simultaneously along with their transition to steady operation and finally to unstarting condition. Comparing the performance curve of every case focused on starting pressure, the unstarting pressure and the minimum secondary pressure, we could derive correlations that the parameters have on the performance of the ejector and presented the optimal design method of the ejector. Additional experiments were carried out to find effects of temperature and mass flow rate of the secondary flow.

• International Journal of Aeronautical and Space Sciences
• /
• 제9권2호
• /
• pp.98-106
• /
• 2008

The motive gas of a supersonic ejector is supplied from different sources depending on the application. The performance of an ejector that is represented by the secondary flow pressure, starting and unstarting pressures heavily depends on the molecular properties of the motive gas. The effects of specific heat ratio of the motive gas were investigated experimentally for an axi-symmetric annular injection type supersonic ejector. Both the starting pressure and unstarting pressure, however, decreased with the increase of the specific heat ratio of the motive gas. It was discovered that the secondary flow pressure increased as the specific heat ratio of the motive gas decreased even if the stagnation pressure of the motive flow was invariant. However, when the motive gas flow nozzle area ratio is large enough for the motive gas to be condensed, different tendency was observed.