• Journal of information and communication convergence engineering
• /
• v.10 no.1
• /
• pp.85-90
• /
• 2012

A 40-MS/sec 10-bit pipelined analog to digital converter (ADC) with a 1.2 Vpp differential input signal is proposed. The implemented pipelined ADC consists of eight stages of 1.5 bit/stage, one stage of 2 bit/stage, a digital error correction block, band-gap reference circuit & reference driver, and clock generator. The 1.5 bit/stage consists of a sub-ADC, digital to analog (DAC), and gain stage, and the 2.0 bit/stage consists of only a 2-bit sub-ADC. A bootstrapped switch with a constant resistance is proposed to improve the linearity of the input switch. It reduces the maximum VGS variation of the conventional bootstrapped switch by 67%. The proposed bootstrapped switch is used in the first 1.5 bit/stage instead of a sample-hold amplifier (SHA). This results in the reduction of the hardware and power consumption. It also increases the input bandwidth and dynamic performance. A reference voltage for the ADC is driven by using an on-chip reference driver without an external reference. A digital error correction with a redundancy is also used to compensate for analog noise such as an input offset voltage of a comparator and a gain error of a gain stage. The proposed pipelined ADC is implemented by using a 0.18-${\mu}m$ 1- poly 5-metal CMOS process with a 1.8 V supply. The total area including a power decoupling capacitor and the power consumption are 0.95 $mm^2$ and 51.5 mW, respectively. The signal-to-noise and distortion ratio (SNDR) is 56.15 dB at the Nyquist frequency, resulting in an effective number of bits (ENOB) of 9.03 bits.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.13 no.5
• /
• pp.473-481
• /
• 2013

A fractional folding analog-to-digital converter (ADC) with a novel arithmetic digital encoding technique is discussed. In order to reduce the asymmetry errors of the boundary conditions for the conventional folding ADC, a structure using an odd number of folding blocks and fractional folding rate is proposed. To implement the fractional technique, a new arithmetic digital encoding technique composed of a memory and an adder is described. Further, the coding errors generated by device mismatching and other external factors are minimized, since an iterating offset self-calibration technique is adopted with a digital error correction logic. A prototype 8-bit 1GS/s ADC has been fabricated using an 1.2V 0.13 um 1-poly 6-metal CMOS process. The effective chip area is $2.1mm^2$(ADC core : $1.4mm^2$, calibration engine : $0.7mm^2$), and the power consumption is 88 mW. The measured SNDR is 46.22 dB at the conversion rate of 1 GS/s. Both values of INL and DNL are within 1 LSB.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.14 no.6
• /
• pp.1145-1152
• /
• 2019

In this paper, a low power current mode 12-bit ADC(: Analog to Digital Converter) is proposed to mix digital circuits and analog circuits with the advantages of low power consumption and high speed operation. The proposed 12 bit ADC is implemented by using 4-bit ADC in a cascade structure, so its power consumption can be reduced, and the chip area can be reduced by using a conversion current mirror circuit. The proposed 12-bit ADC is SK Hynix 350nm process, and post-layout simulation is performed using Cadence MMSIM. It operates at a supply voltage of 3.3V and the area of the proposed circuit is 318㎛ x 514㎛. In addition, the ADC shows the possibility of operating with low power consumption of 3.4mW average power consumption in this paper.

• Proceedings of the IEEK Conference
• /
• 1998.06a
• /
• pp.847-850
• /
• 1998

One of the most difficult problem of designing VLSI is a mixed-circuit design, that is to design circuit containing both analog parts and digital parts. Digital to analog converter and analog to digital converter is a typical case. Especially it can be a serious problem when mixed circuit are put into a large digital circuit like microcontroller. However nowadays this problem is settled by separating analog circuit parts outside the IC. This technique is based on converting a digital signal into a pulse sequence. Then an analog signal is obtained by averaging this pulse sequence at the external low-pass filter. An anlog to digital converter is designed using a stochastic logic instead of a traditional PWM (pulse-width modulation) signal and ins implemente dusing FPGa. Stochastic pulse sequence can be made as a simple circuits and moreover can be mathematically processed by simple circuits -AND gates. The spectral property of stochastic pulse sequence method is better than that of PWM method. So it make easy to design a external low-pass filter. This technique has important advantages, especially the reduction of the ADC cost.

• Journal of IKEEE
• /
• v.24 no.3
• /
• pp.719-726
• /
• 2020

A threshold-voltage sensing circuit is proposed to compensate for pixel aging in active matrix organic light-emitting diodes. The proposed threshold-voltage sensing circuit consists of sample-hold (S/H) circuits and a single-ended successive approximation register (SAR) analog-to-digital converter (ADC) with a resolution of 10 bits. To remove a scale down converter of each S/H circuit and a voltage gain amplifier with a signl-to-differentail converter, the middle reference voltage calibration and input range calibration for the single-ended SAR ADC are performed in the capacitor digital-to-analog converter and reference driver. The proposed threshold-voltage sensing circuit is designed by using a 180-nm CMOS process with a supply voltage of 1.8 V. The ENOB and power consimption of the single-ended SAR ADC are 9.425 bit and 2.83 mW, respectively.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.10 no.4
• /
• pp.132-137
• /
• 2007

The dynamic range of the radar which uses digital signal processors is limited by ADC(Analog-to-Digital Converter). That parameter and ADC loss depend on the noise level of radar receiver. In order to stabilize the performance of radar systems, it is necessary to maintain the noise level constantly. This paper presents the noise AGC(Automatic Gain Control) concept that can keep the noise level constantly and proves that the concept is acceptable through the hardware test and evaluation.

• Journal of Sensor Science and Technology
• /
• v.30 no.4
• /
• pp.223-228
• /
• 2021

This work presents a low-power CMOS image sensor (CIS) with a multi-column-parallel (MCP) readout structure while focusing on improving its performance compared to previous works. A delta readout scheme that utilizes the image characteristics is optimized for the MCP readout structure. By simply alternating the MCP readout direction for each row selection, additional memory for the row-to-row delta readout is not required, resulting in a reduced area of occupation compared to the previous work. In addition, the bias current of a pre-amplifier in a successive approximate register (SAR) analog-to-digital converter (ADC) changes according to the operating period to improve the power efficiency. The prototype CIS chip was fabricated using a 0.18-㎛ CMOS process. A 160 × 120 pixel array with 4.4 ㎛ pitch was implemented with a 10-bit SAR ADC. The prototype CIS demonstrated a frame rate of 120 fps with a total power consumption of 1.92 mW.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.255-258
• /
• 1999

This paper describes a 40-Msample/s 10-bit CMOS folding and interpolating analog-to-digital converter (ADC). A new 2-step architecture is proposed. The proposed architecture is composed of a coarse ADC bloch for the 6bits of MSBs and a fine ADC block for the remaining 4bits. The amplified folding analog signals in the coarse ADC are selectively chosen for the fine ADC. In the fine ADC, the bubble errors of the comparators are corrected by using the BGM(binary-gray-mixed) code[1] and extra two comparators are used to correct underflow and overflow errors. The proposed ADC was simulated using CMOS 0.25${\mu}{\textrm}{m}$ parameters and occupies 1.0mm$\times$1.0mm. The power consumption is 48㎽ at 40MS/s with 2.5-V power supply. The INL is under $\pm$2.0LSB and the DNL. is under $\pm$1.0LSB by Matlab simulations.

• Journal of IKEEE
• /
• v.9 no.1 s.16
• /
• pp.65-71
• /
• 2005

Physical signals generated in the real world are transformed into electrical signals through sensors and fed into electronic circuits. The electrical signals input to electronic circuits are in analog form, thus they must be converted to digital signals using an ADC(Analog-Digital Converter) for digital processing. Signal processing circuits and ADCs that are to be integrated on a single chip together with silicon micro sensors should be designed to have less silicon area and less power consumption. This paper proposed a charge redistribution ADC which reduces silicon area considerably. The proposed method achieves 8 bit conversion by performing 4-bit conversion twice. It reduced the area of capacitor array, which takes most of the ADC area, by 1/16 when compared to a conventional method. Though it uses twice the number of clocks as a conventional method, it would be appropriate to be integrated with a silicon pressure sensor on a single chip since it does not demand high conversion rate.

• Proceedings of the IEEK Conference
• /
• 2001.06b
• /
• pp.45-48
• /
• 2001

An programmable current-mode folding and interpolation analog to digital converter (ADC) with programmable interpolator is proposed in this paper. A programmable interpolator is employed not only to vary the resolution of data converter, but also to decrease a power dissipation within the ADC. Because of varying the number of interpolation circuits, resolution is vary from 6 to 10bit. The designed ADC fabricated by a 0.6${\mu}{\textrm}{m}$ n-well CMOS double metal/single poly process. The experimental result shows the power dissipation from 26 to 87mW with a power supply of 3.3V.