• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제42회 동계 정기 학술대회 초록집
• /
• pp.170-170
• /
• 2012

최근 주목받고 있는 amorphous InGaZnO (a-IGZO) thin film transistors (TFTs)는 수소가 첨가된 비정질 실리콘 TFT (a-Si;H)에 비해 비정질 상태에서도 높은 이동도와 뛰어난 전기적, 광학적 특성에 의해 큰 주목을 받고 있다. 또한 넓은 밴드갭에 의해 가시광 영역에서 투명한 특성을 보이고, 플라스틱 기판 위에서 구부러지는 성질에 의해 플랫 패널 디스플레이나 능동 유기 발광 소자 (AM-OLED), 투명 디스플레이에 응용되고 있다. 하지만, 실제 디스플레이가 동작하는 동안 스위칭 TFT는 백라이트 또는 외부에서 들어오는 빛에 지속적으로 노출되게 되고, 이 빛에 의해서 TFT 소자의 신뢰성에 악영향을 끼친다. 또한, 디스플레이가 장시간 동안 동작 하면 내부 온도가 상승하게 되고 이에 따른 온도에 의한 신뢰성 문제도 동시에 고려되어야 한다. 특히, 실제 AM-LCD에서 스위칭 TFT는 양의 게이트 전압보다 음의 게이트 전압에 의해서 약 500 배 가량 더 긴 시간의 스트레스를 받기 때문에 음의 게이트 전압에 대한 신뢰성 평가는 대단히 중요한 이슈이다. 스트레스에 의한 문턱 전압의 변화는 게이트 절연막과 반도체 채널 사이의 계면 또는 게이트 절연막의 벌크 트랩에 의한 것으로 게이트 절연막의 선택에 따라서 신뢰성을 효과적으로 개선시킬 수 있다. 본 연구에서는 적층된 $Si_3N_4/SiO_2$ (NO 구조) 이중층 구조를 게이트 절연막으로 사용하고, 완충층의 역할을 하는 $SiO_2$막의 두께에 따른 소자의 전기적 특성 및 신뢰성을 평가하였다. a-IGZO TFT 소자의 전기적 특성과 신뢰성 평가를 위하여 간단한 구조의 pseudo-MOS field effect transistor (${\Psi}$-MOSFET) 방법을 이용하였다. 제작된 소자의 최적화된 $SiO_2$ 완충층의 두께는 20 nm이고 $12.3cm^2/V{\cdot}s$의 유효 전계 이동도, 148 mV/dec의 subthreshold swing, $4.52{\times}10^{11}cm^{-2}$의 계면 트랩, negative bias illumination stress에서 1.23 V의 문턱 전압 변화율, negative bias temperature illumination stress에서 2.06 V의 문턱 전압 변화율을 보여 뛰어난 전기적, 신뢰성 특성을 확인하였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제53권5호
• /
• pp.237-241
• /
• 2004

Amorphous silicon (a-Si) films are used in a broad range of solar cell, flat panel display, and sensor. Because of the greater ease of deposition and lower processing temperature, thin films are widely used for thin film transistors (TFTs). However, they have lower stability under the exposure of visible light and because of their low field effect mobility ($\mu$$_{FE}$ ) , less than 1 c $m^2$/Vs, they require a driving IC in the external circuits. On the other hand, polycrystalline silicon (poly-Si) thin films have superiority in $\mu$$_{FE}$ and optical stability in comparison to a-Si film. Many researches have been done to obtain high performance poly-Si because conventional methods such as excimer laser annealing, solid phase crystallization and metal induced crystallization have several difficulties to crystallize. In this paper, a new crystallization process using a molybdenum substrate has been proposed. As we use a flexible substrate, high temperature treatment and roll-to-roll process are possible. We have used a high temperature process above 75$0^{\circ}C$ to obtain poly-Si films on molybdenum substrates by a rapid thermal annealing (RTA) of the amorphous silicon (a-Si) layers. The properties of high temperature crystallized poly-Si studied, and poly-Si has been used for the fabrication of TFT. By this method, we are able to achieve high crystal volume fraction as well as high field effect mobility.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.107-108
• /
• 2008

The spectacular development of AMLCDs, been made possible by a-Si:H technology, still faces two major drawbacks due to the intrinsic structure of a-Si:H, namely a low mobility and most important a shift of the transfer characteristics of the TFTs when submitted to bias stress. This has lead to strong research in the crystallization of a-Si:H films by laser and furnace annealing to produce polycrystalline silicon TFTs. While these devices show improved mobility and stability, they suffer from uniformity over large areas and increased cost. In the last decade we have focused on microcrystalline silicon (${\mu}c$-Si:H) for bottom gate TFTs, which can hopefully meet all the requirements for mass production of large area AMOLED displays [1,2]. In this presentation we will focus on the transfer of a deposition process based on the use of $SiF_4$-Ar-$H_2$ mixtures from a small area research laboratory reactor into an industrial gen 1 AKT reactor. We will first discuss on the optimization of the process conditions leading to fully crystallized films without any amorphous incubation layer, suitable for bottom gate TFTS, as well as on the use of plasma diagnostics to increase the deposition rate up to 0.5 nm/s [3]. The use of silicon nanocrystals appears as an elegant way to circumvent the opposite requirements of a high deposition rate and a fully crystallized interface [4]. The optimized process conditions are transferred to large area substrates in an industrial environment, on which some process adjustment was required to reproduce the material properties achieved in the laboratory scale reactor. For optimized process conditions, the homogeneity of the optical and electronic properties of the ${\mu}c$-Si:H films deposited on $300{\times}400\;mm$ substrates was checked by a set of complementary techniques. Spectroscopic ellipsometry, Raman spectroscopy, dark conductivity, time resolved microwave conductivity and hydrogen evolution measurements allowed demonstrating an excellent homogeneity in the structure and transport properties of the films. On the basis of these results, optimized process conditions were applied to TFTs, for which both bottom gate and top gate structures were studied aiming to achieve characteristics suitable for driving AMOLED displays. Results on the homogeneity of the TFT characteristics over the large area substrates and stability will be presented, as well as their application as a backplane for an AMOLED display.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1459-1462
• /
• 2008

In this paper we describe solutions to address critical challenges in direct fabrication of amorphous silicon thin film transistor (TFTs) arrays for active matrix flexible displays. For all flexible substrates a manufacturable handling protocol in automated display-scale equipment is required. For metal foil substrates the principal challenges are planarization and electrical isolation, and management of stress (CTE mismatch) during TFT fabrication. For plastic substrates the principal challenge is dimensional instability management.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2008년도 International Meeting on Information Display
• /
• pp.1203-1207
• /
• 2008

For a large sized, ultra definition (UD) and high refresh rate for motion blur free AMLCD TVs, amorphous IGZO thin film transistor (TFT) are applied and investigated in terms of threshold voltage ($V_{th}$) shift influenced by active layer thickness uniformity, source drain etching technology, heat treatment and passivation condition. Optimizing above parameters, we fabricated the world's largest 15 inch XGA AMLCD successfully.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.80-81
• /
• 2008

Schottky barrier thin film transistors (SB-TFT) on polycrystalline silicon(poly-Si) are fabricated by platinum silicided source/drain for p-type SB-TFT. High quality poly-Si film were obtained by crystallizing the amorphous Si film with excimer laser annealing (ELA) or solid phase crystallization (SPC) method. The fabricated poly-Si SB-TFTs showed low leakage current level and a large on/off current ratio larger than $10^5$. Significant improvement of electrical characteristics were obtained by the additional forming gas annealing in 2% $H_2/N_2$ ambient, which is attributed to the termination of dangling bond at the poly-Si grain boundaries as well as the reduction of interface trap states at gate oxide/poly-Si channel.

• 전자공학회논문지 IE
• /
• 제43권2호
• /
• pp.11-15
• /
• 2006

FPD (flat panel display)의 능동구동 (active matrix) 방식의 플렉시블 디스플레이를 위해 PES의 플라스틱 기판위에 극저온 다결정 실리콘 박막 트랜지스터를 제작하였다. 상온에서도 박막의 증착이 가능한 RF 마크네트론 스퍼터링과 양질의 다결정 실리콘 박막을 얻을 수 있다고 알려진 XeCl 엑시머 레이져 열처리를 이용하였으며 모든 공정이 150$^{\circ}C$ 이하의 극저온에서 이루어졌다. 플라스틱 기판에 형성한 실리콘 박막 트랜지스터는 344 $mJ/cm^2$ 의 에너지 밀도에서 결정화 하였을 때 이동도 63.64$cm^2/V$ 로 기판에 회로를 집적할 수 있기에 충분한 특성을 얻을 수 있었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1582-1584
• /
• 1996

The polycrystalline silicon thin film transistors (poly-Si TFT) are the most promising candidate for active matrix liquid crystal displays (AMLCD) for their high mobilities and current driving capabilities. The leakage current of the poly-Si TFT is much higher than that of the amorphous-Si TFT, thus larger storage capacitance is required which reduces the aperture ratio fur the pixel. The offset gated poly-Si TFTs have been widely investigated in order to reduce the leakage current. The conventional method for fabricating an offset device may require additional mask and photolithography process step, which is inapplicable for self-aligned source/drain ion implantation and rather cost inefficient. Due to mis-alignment, offset devices show asymmetric transfer characteristics as the source and drain are switched. We have proposed and fabricated a new offset poly-Si TFT by applying photoresist reflow process. The new method does not require an additional mask step and self-aligned ion implantation is applied, thus precise offset length can be defined and source/drain symmetric transfer characteristics are achieved.

• E2M - 전기 전자와 첨단 소재
• /
• 제11권11호
• /
• pp.22-27
• /
• 1998

We have investigated the effect of an ion shower doping of the laser annealed poly-Si films at an elevated substrate temperatures. The substrate temperature was varied from room temperature to 300$^{\circ}C$ when the poly-Si film was doped with phosphorus by a non-mass-separated ion shower. Optical, structural, and electrical characterizations have been performed in order to study the effect of the ion showering doping. The sheet resistance of the doped poly-Si films was decreased from7${\times}$106 $\Omega$/$\square$ to 700 $\Omega$/$\square$ when the substrate temperature was increased from room temperature to 300$^{\circ}C$. This low sheet resistance is due to the fact that the doped film doesn't become amorphous but remains in the polycrystalline phase. The mildly elevated substrate temperature appears to reduce ion damages incurred in poly-Si films during ion-shower doping. Using the ion-shower doping at 250$^{\circ}C$, the field effect mobility of 120 $\textrm{cm}^2$/(v$.$s) has been obtained for the n-channel poly-Si TFTs.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.354-355
• /
• 2013

최근 디스플레이 분야에서 amorphous InGaZnO (a-IGZO) thin film transistors (TFTs)는 a-Si:H에 비해 비정질 상태에서도 비교적 높은 이동도를 가지고 다결정 Si 반도체에 비해 저온공정이 가능하고 대면적화가 용이한 장점 때문에 주목받고 있다. 또한 넓은 밴드갭을 가지기 때문에 가시광선 영역에서 투명하여 투명소자에도 응용이 가능하다. 본 연구에서는 RF magnetron sputtering법을 이용하여 RF power의 변화에 따라 IGZO 박막의 positive bias stress (PBS)에 대한 안정성을 조사하였다. 소결된 타겟으로는 In:Ga:ZnO를 각각 2:2:1 mol%의 조성비로 소결하여 이용하였고, 공정 조건은 초기 압력 Torr, 증착 압력 Torr, Ar：O2=18：12 sccm로 고정하였다. 공정 변수로는 130 W, 150 W, 170 W, 200 W로 변화를 주어 실험을 진행하였다. PBS 측정은 gate bias를 10 V로 고정하여 stress 시간을 각각 0, 30, 100, 300, 1,000, 3,000, 7,000초를 적용하였다. 측정 결과 RF power가 증가할수록 문턱전압의 변화량이 증가하는 것을 보였다. 130 W의 경우 4.47 V의 변화량을 보였지만 200 W의 경우는 10.01 V로 증가되어 나타났다. 따라서 RF power을 낮추어 만들어진 소자의 경우 RF power를 높여 만들어진 소자에 비해 PBS에 대한 안정성이 더 높은 결과를 확인하였다.