• Transactions on Electrical and Electronic Materials
• /
• v.18 no.1
• /
• pp.55-57
• /
• 2017

Amorphous oxide thin film transistors (TFTs) were fabricated with 0.5 wt% silicon doped zinc tin oxide (a-0.5SZTO) thin film deposited by radio frequency (RF) magnetron sputtering. In order to investigate the effect of annealing treatment on the electrical properties of TFTs, a-0.5SZTO thin films were annealed at three different temperatures ($300^{\circ}C$, $500^{\circ}C$, and $700^{\circ}C$ for 2 hours in a air atmosphere. The structural and electrical properties of a-0.5SZTO TFTs were measured using X-ray diffraction and a semiconductor analyzer. As annealing temperature increased from $300^{\circ}C$ to $500^{\circ}C$, no peak was observed. This provided crystalline properties indicating that the amorphous phase was observed up to $500^{\circ}C$. The electrical properties of a-0.5SZTO TFTs, such as the field effect mobility (${\mu}_{FE}$) of $24.31cm^2/Vs$, on current ($I_{ON}$) of $2.38{\times}10^{-4}A$, and subthreshold swing (S.S) of 0.59 V/decade improved with the thermal annealing treatment. This improvement was mainly due to the increased carrier concentration and decreased structural defects by rearranged atoms. However, when a-0.5SZTO TFTs were annealed at $700^{\circ}C$, a crystalline peak was observed. As a result, electrical properties degraded. ${\mu}_{FE}$ was $0.06cm^2/Vs$, $I_{ON}$ was $5.27{\times}10^{-7}A$, and S.S was 2.09 V/decade. This degradation of electrical properties was mainly due to increased interfacial and bulk trap densities of forming grain boundaries caused by the annealing treatment.

• Korean Journal of Materials Research
• /
• v.8 no.2
• /
• pp.147-153
• /
• 1998

Tungsten nitride is very attractive as absorber for X-ray lithographic mask and as a diffusion barrier for interconnecting metallization in Si VLSI technology. Microstructure of tungsten nitride films prepared by RF magnetron sputtering has been investigated as a function of deposition parameter. The crystal structure of sputtered films on silicon nitride membrane depends strongly on the NJAr gas flow ratio(0~18%1, gas pressure(l0~43mTorr). RF power (60~150W), target-substrate distance(4~8cm). Tungsten nitride films deposited at the $N_2/Ar$ gas flow ratio(- 10%). gas pressure(~10mmTorr), RF power(~150W) and target-substrate distance(6cm) are amorphous, but at other conditions are almost rough -surfaced polycrystalline. Amorphous films are very smooth($3.1\AA$ rms) and expected to be excellent absorber for X-ray mask.

• Journal of the Korean Ceramic Society
• /
• v.50 no.4
• /
• pp.301-307
• /
• 2013

SiC hollow fiber was fabricated by curing, dissolution and sintering of Al-PCS fiber, which was melt spun the polyaluminocarbosilane. Al-PCS fiber was thermally oxidized and dissolved in toluene to remove the unoxidized area, the core of the cured fiber. The wall thickness ($t_{wall}$) of Al-PCS fiber was monotonically increased with an increasing oxidation curing time. The Al-PCS hollow fiber was heat-treated at the temperature between 1200 and $2000^{\circ}C$ to make a SiC hollow fibers having porous structure on the fiber wall. The pore size of the fiber wall was increased with the sintering temperature due to the decomposition of the amorphous $SiC_xO_y$ matrix and the growth of ${\beta}$-SiC in the matrix. At $1400^{\circ}C$, a nano porous wall with a high specific surface area was obtained. However, nano pores grew with the grain growth after the thermal decomposition of the amorphous matrix. This type of SiC hollow fibers are expected to be used as a substrate for a gas separation membrane.

• Korean Journal of Metals and Materials
• /
• v.49 no.6
• /
• pp.498-504
• /
• 2011

We examined the microstructure and optical properties of crystallized ~30 nm-ZnO/~10 nm amorphous $TiO_2$ nano bilayered films as nano electrodes were deposited at extremely low substrate temperatures of $150-210^{\circ}C$. The bilayered films were deposited on silicon substrates with 10 cm diameters by ALD (atomic layer deposition) using DEZn (diethyl zinc(Zn(C2H5)2)) and TDMAT (tetrakis dimethyl-amid $titanium(Ti(N(CH_3)_2)_4)$ as the ZnO and $TiO_2$ precursors, respectively, and $H_2O$ as the oxidant. The microstructure, phase, and optical properties of the bilayered films were examined by FE-SEM, TEM, XRD, AES, and UV-VIS-NIR spectroscopy. FE-SEM and TEM showed that all bilayered films were deposited very uniformly and showed crystallized ZnO and amorphous $TiO_2$ layers. AES depth profiling showed that the ZnO and $TiO_2$ films had a stoichiometric composition of 1:1 and 1:2, respectively. These bilayered films have optical absorption properties in a wide range of ultraviolet wavelengths, 250-390 nm, whereas the single ZnO and $TiO_2$ films showed an absorption range of 350-380nm.

• Composites Research
• /
• v.30 no.2
• /
• pp.77-83
• /
• 2017

Liquid silicon infiltration, which is one of the methods of producing fiber reinforced ceramic composites, has several advantages such as low fabrication cost and good shape formability. In order to confirm LSI process feasibility of SiC fiber, $SiC_f/SiC$ composites were fabricated using three types of SiC fibers (Tyranno SA, LoxM, Tyranno S) which have different crystallinity and oxygen content. Composites that were fabricated with LSI process were well densified by less than 2% of porosity, but showed an obvious difference in 3-point bending strength according to crystallinity and oxygen content. When composites in LSI process was exposed to a high temperature, crystallization and micro structural changes were occurred in amorphous SiOC phase in SiC fiber. Fiber shrinkage also observed during LSI process that caused from reaction in fiber and between fiber and matrix. These were confirmed with changes of process temperature by SEM, XRD and TEM analysis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.28 no.6
• /
• pp.351-359
• /
• 2015

Next-generation displays should be transparent and flexible as well as having high resolution and frame number. The main factor for active matrix organic light emitting diode and next-generation displays is the development of TFTs (thin-film transistors) with high mobility and large area uniformity. The TFTs used for transparent displays are mainly oxide TFT that has oxide semiconductor as channel layer. Zinc-oxide based substances such as indium-gallium-zinc-oxide has attracted attention in the display industry. In this paper, the mobility improvement of low cost oxide TFT is studied for fast operating next-generation displays by overcoming disadvantages of amorphous silicon TFT that has low mobility and poly silicon TFT that requires expensive equipment for complex process and doping process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2016.02a
• /
• pp.147.2-148
• /
• 2016

Light management technology is very important for thin film solar cells, which can reduce optical reflection from the surface of thin film solar cells or enhance optical path, increasing the absorption of the incident solar light. Using proper light trapping structures in hydrogenated amorphous silicon (a-Si:H) solar cells, the thickness of absorber layers can be reduced. Instead, the internal electric field in the absorber can be strengthened, which helps to collect photon generated carriers very effectively and to reduce light-induced loss under long-term light exposure. In this work, we introduced a chemical etching technology to make honey-comb textures on glass substrates and analyzed the optical properties for the textured surface such as transmission, reflection and scattering effects. Using ray optics and finite difference time domain method (FDTD) we represented the behaviors of light waves near the etched surfaces of the glass substrates and discussed to obtain haze parameters for the different honey-comb structures. The simulation results showed that high haze values were maintained up to the long wavelength range over 700 nm, and with the proper design of the honey-comb structure, reflection or transmission of the glass substrates can be enhanced, which will be very useful for the multi-junction (tandem or triple junction) thin film a-Si:H solar cells.

• Advanced Composite Materials
• /
• v.18 no.4
• /
• pp.339-350
• /
• 2009

Al-Fe-V-Si alloys reinforced with SiC particles were prepared by multi-layer spray deposition technique. Both microstructures and mechanical properties including hardness and tensile properties development during hot exposure process of Al-8.5Fe-1.3V-1.7Si, Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$ and Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ were investigated. The experimental results showed that an amorphous interface of about 3 nm in thickness formed between SiC particles and the matrix. SiC particles injected silicon into the matrix; thus an elevated silicon concentration was found around $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids, which subsequently inhibited the coarsening and decomposition of $\alpha-Al_{12}(Fe,\;V)_3Si$ dispersoids and enhanced the thermostability of the alloy matrix. Moreover, the thermostability of microstructure and mechanical properties of Al-10.0Fe-1.3V-2Si/15 vol% $SiC_P$ are of higher quality than those of Al-8.5Fe-1.3V-1.7Si/15 vol% $SiC_P$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.110.2-110.2
• /
• 2011

일본 Sanyo 사에 의해서 획기적으로 HIT 태양전지가 개발된 바 있다. 이러한 HIT 태양전지는 기존의 확산-접합 Si 태양전지에 비해서 저비용 고효율의 장점을 갖는다: 22% 이상의 변환효율, $200^{\circ}C$ 이하의 공정온도, 낮은 태양전지 온도 의존도, 높은 개방전압. 한편 Sanyo사의 HIT 태양전지는 n-형 Si 웨이퍼를 이용한 반면에, 최근 미국 National Renewable Energy Laboratory는 p-형 Si 웨이퍼를 이용해서 변환효율 19% 대의 HIT 태양전지를 개발한 바 있다. 그 동안 지속적으로 p-형 Si HIT 태양전지를 고효율화하기(< 22%) 위해서 많은 노력이 진행되어 왔지만 이와 같은 노력에도 불구하고 아직 p-형 HIT는 n-형 HIT 태양전지에 비해서 다소 성능면에서 떨어져 있다. 본 연구는 n- 및 p-형 실리콘 웨이퍼로 구성된 HIT 태양전지의 물리적인 차이점에 초점을 맞추고, 결정 및 비정질 실리콘 층의 역할에 대해서 연구하였다. 특히 태양전지 효율을 향상시키는 요소들로서 결정 실리콘의 불순물 준위(n- 및 p-형) 또는 비저항, 비정질 실리콘으로 구성된 emitter 층, intrinsic 층, 경계면이 고려되었다. 그리고 이러한 요소들이 HIT 태양전지에 미치는 영향을 조사하기 위해서 AMPS-1D 컴퓨터 프로그램을 사용하였고, 이를 통해서 HIT 태양전지의 결정 및 비정질 실리콘 층의 역할을 물리적 정량적으로 분석하였다. 본 연구에 적용되는 HIT는 ITO/a-Si:H(p+)/a-Si:H(i)/c-Si(n)/a-Si:H(i)/a-Si:H(n+) 및 ITO/a-Si:H(n+)/a-Si:H(i)/c-Si(p)/a-Si:H(i)/a-Si:H(p+)의 구조로서 다음과 같은 태양전지 특성을 갖는다: n-형 HIT의 경우, fill factor ~ 0.78, 단락전류밀도 ~ 38.1 $mA/cm^2$, 개방전압 0.74 V, 변환효율 22.3 % (그리고 p-형 HIT의 경우, fill factor ~ 0.76, 단락전류밀도 ~ 36.5 $mA/cm^2$, 개방전압 0.69 V, 변환효율 19.4 %).

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.230-230
• /
• 2013

In amorphous or microcrystalline thin-film silicon solar cells, p-i-n structure is used instead of p/n junction structure as in wafer-based Si solar cells. Hence, these p-i-n structured solar cells inevitably consist of many interfaces and the cell efficiency critically depends on the effective control of these interfaces. In this study, in-situ plasma treatment process of the interfaces was developed to improve the efficiency of a-Si:H solar cell. The p-i-n cell was deposited using a single-chamber VHF-PECVD system, which was driven by a pulsed-RF generator at 80 MHz. In order to solve the cross-contamination problem of p-i layer, high RF power was applied without supplying SiH4 gas after p-layer deposition, which effectively cleaned B contamination inside chamber wall from p-layer deposition. In addition to the p-i interface control, various interface control techniques such as thin layer of TiO2 deposition to prevent H2 plasma reduction of FTO layer, multiple applications of thin i-layer deposition and H2 plasma treatment, H2 plasma treatment of i-layer prior to n-layer deposition, etc. were developed. In order to reduce the reflection at the air-glass interface, anti-reflective SiO2 coating was also adopted. The initial solar cell efficiency over 11% could be achieved for test cell area of 0.2 $cm^2$.