• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.6
• /
• pp.317-322
• /
• 2016

While PFOS sodium salt ($C_8F_{17}SO_3Na$) was not degraded by microorganisms for 28 days, the 4 alternatives were biodegraded at the rates of 21.6% for $C_{25}F_{17}H_{32}S_3O_{13}Na_3$, 20.5% for $C_{15}F_9H_{21}S_2O_8Na_2$, 15.8% for $C_{23}F_{18}H_{28}S_2O_8Na_2$ and 6.4% for $C_{17}F_9H_{25}S_2O_8Na_2$, respectively. The acute toxicity test using Daphnia magna was conducted for 48 hours, the half effective concentration ($EC_{50}$) of PFOS sodium salt ($C_8F_{17}SO_3Na$) was evaluated in 54.5 mg/L. While the 4 alternatives did not show any effect at 500.0 mg/L. The surface tension of the PFOS salt ($C_8F_{17}SO_3Na$) is 46.2 mN/m at a concentration of 500.0 mg/L. While the surface tension of the 4 alternatives was found to be superior to PFOS sodium salt ($C_8F_{17}SO_3Na$). The surface tension of $C_{23}F_{18}H_{28}S_2O_8Na_2$ (20.9 mN/m) has the lowest, followed by $C_{15}F_9H_{21}S_2O_8Na_2$ (23.4 mN/m), $C_{17}F_9H_{25}S_2O_8Na_2$ (27.3 mN/m), $C_{25}F_{17}H_{32}S_3O_{13}Na_3$ (28.2 mN/m). The four kinds of alternatives ($C_{15}F_9H_{21}S_2O_8Na_2$, $C_{17}F_9H_{25}S_2O_8Na_2$, $C_{23}F_{18}H_{28}S_2O_8Na_2$, $C_{25}F_{17}H_{32}S_3O_{13}Na_3$) were found to be superior to PFOS sodium salt ($C_8F_{17}SO_3Na$) in terms of biodegradation, Daphnia sp. acute toxicity and surface tension, and thus they were considered applicable as PFOS alternatives. Especially biodegradation rate of $C_{15}F_9H_{21}S_2O_8Na_2$, $C_{23}F_{18}H_{28}S_2O_8Na_2$ and $C_{25}F_{17}H_{32}S_3O_{13}Na_3$ was relatively high as 15.8~21.6%, and Daphnia sp. acute toxicity and surface tension were considerably superior (surface tension 39~55%) to PFOS sodium salt. Therefore, these alternatives are considered to be available as an alternative of PFOS.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.1
• /
• pp.1-12
• /
• 2010

According to the capacity design concept which forms the basis of the current steel seismic codes, the braces in concentrically braced frames (CBFs) should dissipate seismic energy through cyclic tension yielding and cyclic compression buckling while the beams and the columns should remain elastic. Brace buckling in inverted V-braced frames induces unbalanced vertical forces which, in turn, impose the additional beam moments and column axial forces. However, due to difficulty in predicting the location of buckling stories, the most conservative approach implied in the design code is to estimate the column axial forces by adding all the unbalanced vertical forces in the upper stories. One alternative approach, less conservative and recommended by the current code, is to estimate the column axial forces based on the amplified seismic load expected at the mechanism-level response. Both are either too conservative or lacking technical foundation. In this paper, three combination rules for a rational estimation of the column axial forces were proposed. The idea central to the three methods is to detect the stories of high buckling potential based on pushover analysis and dynamic behavior. The unbalanced vertical forces in the stories detected as high buckling potential are summed in a linear manner while those in other stories are combined by following the SRSS(square root of sum of squares) rule. The accuracy and design advantage of the three methods were validated by comparing extensive inelastic dynamic analysis results. The mode-shape based method(MSBM), which is both simple and accurate, is recommended as the method of choice for practicing engineers among the three.

• Korean Journal of Environmental Agriculture
• /
• v.16 no.2
• /
• pp.170-174
• /
• 1997

Constructed wetland system was studied to treat wastewater from industrial complex in rural area. Pilot plant at the Baeksuk Nongkong Danzi in Chunahn-City was used for field study. For the DO, the effluent concentration was higher than the influent concentration and it implies that natural reaeration supplies enough oxygen to the system. For the SS, the effluent concentration was consistently lower than the water quality standard even though the influent concentration varied significantly, which showed that SS was removed by the system effectively which is consist of soil and plants. For the BOD and COD, the average removal rate of them were 56% and 43%, respectively, therefore, the effluent concentration could not meet water quality standards when influent concentration was high. The removal rate of BOD and COD can be improved by supplemental treatment in addition to this system if necessary. For the T-N and T-P, the influent concentration of them were lower than the water quality standards than no further treatment was needed. Overall, the result showed that constructed wetland system is a feasible alternative for the treatment of wastewater from industrial complex in rural area. For actual application of this system, further study on design factors including loading rate, removal mechanism, and temperature effects is required to meet water quality standard consistently. Compared to existing systems, this system is quite competitive because it requires low capital cost, almost no energy and maintenance, and therefore, very cost effective.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.42 no.1
• /
• pp.104-114
• /
• 2014

Nowadays, forests have been recognized as valuable resources for biological diversity and tourism/recreation. Temple forests occupy 1.3% of all the Korean forest and are under weak management although their ecological states are very good. Currently in the Buddhist society, the concern for the Buddhist arboretum has been raised as a good alternative for the practical use of temple forests to secure the sustainability of the temple forests as well as to actively meet the demand of the times for forests. This study aims to suggest establishment measures of Buddhist arboretum. This survey was performed on 105 temple forest managers and 130 laypersons. To summarize the results, the two groups differ in opinion. The temple forest managers more concerned for advertizing Buddhist culture and enhancing the image of the temple, while the laypersons had higher expectations for relaxation and education. However, they are similar in putting more emphasis on the conserving the heritage value of the temple and managing the temple forest. Above all, both groups evaluated the needs higher than the urgency and perceived managing temple forest as the most crucial function of a Buddhist arboretum. They also thought that a Buddhist arboretum should be planned to respond to the ecological characteristics of the temple area as well as to be non-exclusive to its users. Based on the important findings, five suggestions for a Buddhist arboretum were proposed. First, a Buddhist arboretum should be carried forward from a long-term point of view, developing a bond of sympathy between members of Buddhist society as well as conducting promotion and education to the general public. Second, the most significant function of a Buddhist arboretum should be preserving the temple forest, with the emphasis on relaxation and education. Third, in order to provide nonexclusive use, a Buddhist arboretum should provide mixed programs applicable to diverse user groups for high user satisfaction and educational effects. Fourth, the Buddhistic identification could be obtained through variety of plants closely associated with Buddhist culture. Lastly, in the process of collecting plants, it is also crucial to reflect the image of the temple and resource property so as to contribute itself in conservation and management of original temple forests. Thereby all Buddhist Arboretum can be classified into two types; preservation/collection and display/education/rest.

• Journal of the Korean earth science society
• /
• v.18 no.6
• /
• pp.453-463
• /
• 1997

The contents of high school 'Common science' textbooks was analyzed qualitatively and quantitatively. Seven common science textbooks were selected and its contents, structure, inquiry, activities, appendix and its characteristics were investigated, and analyzed using the Goal Clusters of Project Synthesis and Romey's indices of text evaluation were calculated. The contents of each unit are not much different among textbooks because they are written according to the curriculum ordinance and textbook guidelines of the Ministry of Education. The textbooks was consist of $471{\sim}519$ pages. It was distribute similarly among the chapter of 'materials', 'forces', lives' and 'earth'. The chapter of 'energy' and 'environment' was treat significantly. The contents and structure of common science is a mere physical consolidation. I make an alternative plan that a topic form. Inquiry activities used in the textbooks are 11 type, however most of that is interpretation of data, experiment, survey and discussion. Ninety six percents of the experiment, belong to the 1st level, four percents of that belong to the 2nd level of the Schwab's inquiry level and there are no activities of the 3rd level. Little attention is given to Goal Cluster I, II, IV in the common science textbooks currently employed. Its content should be broadened to include all Goal Clusters of Project Synthesis. Homey's indices representing the degrees of student involvement. are $0.57{\sim}1.14$ for sentence analysis, $0.60{\sim}1.67$ for figure and diagram analysis, $0.67{\sim}1.50$ for analysis of questions at chapter ends, respectively, student activity per page investigated being $0.6{\sim}0.9$. But chapter summaries cease to repeats the conclusions of the chapter also it be rather formally and inattentively written.

• Progress in Medical Physics
• /
• v.8 no.2
• /
• pp.87-102
• /
• 1997

The absolute absorbed dose can be determined according to the measurement conditions; measurement material, detector, energy and calibration protocols. The purpose of this study is to compare the absolute absorbed dose due to the differences of measurement condition and calibration protocols for photon beams. Dosimetric measurements were performed with a farmer type PTW and NEL ionization chambers in water, solid water, and polystyrene phantoms using 6MV photon beams from Siemens linear accelerator. Measurements were made along the central axis of 10cm $\times$ 10cm field size for constant target to surface distance of 100cm for water, solid water and polystyrene phantom. Theoretical absorbed dose intercomparisons between TG21 and IAEA protocol were performed for various measurement combinations of phantom, ion chamber, and electrometer. There were no significant differences of absorbed dose value between TG21 and IAEA protocol. The differences between two protocols are within 1％ while the average value of IAEA protocol was 0.5％ smaller than TG21 protocol. For the purpose of comparison, all the relative absorbed dose were nomalized to NEL ion chamber with Keithley electrometer and water phantom, The average differences are within 1％, but individual discrepancies are in the range of - 2.5％ to 1.2％ depending upon the choice of measurement combination. The largest discrepancy of - 2.5％ was observed when NEL ion chamber with Keithley electrometer is used in solid water phantom. The main cause for this discrepancy is due to the use of same parameters of stopping power, absorption coeficient, etc. as used in water phantom. It should be mentioned that the solid water phantom is not recommended for absolute dose calibration as the alternative of water, since absorbed dose show some dependency on phantom material other than water. In conclusion, the trend of variation was not much dependent on calibration protocol. However, it shows that absorbed dose could be affected by phantom material other than water.

• Progress in Medical Physics
• /
• v.26 no.4
• /
• pp.250-257
• /
• 2015

Multi-leaf collimator (MLC) systems are frequently used to deliver photon-based radiation, and allow conformal shaping of treatment beams. Many proton beam centers currently make use of aperture and snout systems, which involve use of a snout to shape and focus the proton beam, a brass aperture to modify field shape, and an acrylic compensator to modulate depth. However, it needs a lot of time and cost of preparing treatment, therefore, we developed the manual MLC for solving this problem. This study was carried out with the intent of designing an MLC system as an alternative to an aperture block system. Radio-activation and dose due to primary proton beam leakage and the presence of secondary neutrons were taken into account during these iterations. Analytical calculations were used to study the effects of leaf material on activation. We have fabricated tray model for adoption with a wobbling snout ($30{\times}40cm^2$) system which used uniform scanning beam. We designed the manual MLC and tray and can reduce the cost and time for treatment. After leakage test of new tray, we upgrade the tray with brass and made the safety tool. First, we have tested the radio-activation with usually brass and new brass for new manual MLC. It shows similar behavior and decay trend. In addition, we have measured the leakage test of a gantry with new tray and MLC tray, while we exposed the high energy with full modulation process on film dosimetry. The radiation leakage is less than 1%. From these results, we have developed the design of the tray and upgrade for safety. Through the radio-activation behavior, we figure out the proton beam leakage level of safety, where there detects the secondary particle, including neutron. After developing new design of the tray, it will be able to reduce the time and cost of proton treatment. Finally, we have applied in clinic test with original brass aperture and manual MLC and calculated the gamma index, 99.74% between them.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.4
• /
• pp.75-85
• /
• 2012

This study was investigated to develop an alternative medium for the cultivation of oyster mushrooms. The cultivation characteristics for major cultivated varieties of oyster mushrooms were campared with the food waste medium. In addition, water control & a gap formation of food waste is being pointed out as a problem of the medium material. Therefore, certain amounts of earthworm casting were supplied to the food waste medium to overcome the water and compaction phenomenon. This study investigated the use of the total 6 cultivars of oyster mushrooms, the Suhan(PL.1), Chiak No. 5(PL.2), Chiak No. 7(PL.3), Samgu No. 5(PL.4), Samgu No. 8(PL.5), Jangan No. 5(PL.6). In terms of medium, the optimum growth of the mycelium of the oyster mushroom was observed in the beet pulp medium but in food waste, the mycelium's growth was observed as insufficient in the bulk of cultivars. The Jangan No. 5(PL.6) was superior to other cultivars relative to the mycelium's growth. The optimum concentration of earthworm casting added the foodwaste medium was 30%. When Jangan No. 5(PL.6) was incubated in the foodwaste meidum containing 30% earthworm casting, the early days to germination were long, almost double the amount of time than that of the beet pulp medium. However, it was found that the fruit body size was larger than that of the beet pulp by up to 20.5%, and the length of the fruit body was up to 6.2% longer than that of the beet plup. The total yields increased by 60.5%. The analysis results of the oyster mushroom's nutritional contents cultured using the food waste medium, shows that the protein, vitamin A and vitamin E increased 70.6%, 2.4%, 0.8% respectively, the fat decreased by 12.6% and the oleic acid increased in a very small amount compared to that of the beet pulp medium.

• The Korean Journal of Food And Nutrition
• /
• v.11 no.2
• /
• pp.179-184
• /
• 1998

As a way of mass process of onion, Allium cepa L., the oleoresin decompressed and concentrated is an alternative process to minimize lowering in the quality of onion during storage, to improve the original flavor and taste, and to increase variety as processing aids. This study was performed to investigate on the quality stability during storage of oleoresin. Oleoresin product was manufactured by mixing a concentration of onion juice and ethanol extract homogenously, emulsified by an additional 2% PGDR(polyglycerol condensed ricinoleate) and 1% cysteine. During 60 days storage at 5$^{\circ}C$, $25^{\circ}C$ and 4$0^{\circ}C$ the total sugar content in oleoresin product was very stable, and absorbances at 420nm as browning reaction index were 0.38, 1.53 and 3.32, respectively, addition of 1% cysteine retarded the browning reaction effectively. When oleoresin product was centrifuged(2000$\times$G, 60 minutes), the volumes of emulsion level without separation were 96.8%, 94.1% and 9.06%, respectively during 20 days, 40 days and 60 days storage at 5$^{\circ}C$, and those during 60 days storage at $25^{\circ}C$ and 4$0^{\circ}C$ were appeared to be 83.2% and 75.4%. Showing lower level as increasing storage temperature. Antioxidant indexes(AI) of soybean oil added 1% oleoresin without storage and 0.02% BHA were 1.39 and 1.72. The former showed 80.8% antioxidant activity on induction time extension effect of the latter. Antioxidant indexes of oleoresin decreased slightly as increasing storage temperature and were 1.37, 1.30 and 1.08. Total pyruvate contents were 89.9%, 79.7% and 65.2%, respectively during 60 days storage at 5$^{\circ}C$, $25^{\circ}C$ and 4$0^{\circ}C$. Rate constant, Q10 value and activation energy were 1.381~4.735 mmol/$\ell$.hr, 1.537~1.694 and 11.649 ㎉/g mole for the reduction of pyruvates in the range of storage temperatures during oleoresin storage.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.26 no.1
• /
• pp.5-12
• /
• 2018

As many local governments have faced increasing conflicts on landfill use and the time of end use, it is difficult to provide an alternative landfill or conclude a consensus of lifespan extension for the existing landfill site. Therefore, the purpose of this study is to contribute improving of the landfill capacity by calculating the resource recovery potentials of landfilled waste previously and in the future by landfill mining. For this, rate of volume increase, weight ratio, and apparent density were adopted as major parameters and their values were calculated through previous cases. The rate of volume increase was calculated to 1.42 by averaging previous cases of three areas. The average weight ratio of soil matter was 45.6% by calculating for the three areas. For the combustible waste and incombustible waste, statistical data can be used. The apparent densities were divided by combustible waste, incombustible waste, and soil matter using an average of two areas value, i.e., $0.35ton/m^3$, $1.40ton/m^3$ and $1.58ton/m^3$. We analyzed the resource recovery potential of Cheongju landfill by using the estimated parameters. The additional landfill capacity was 45% of the existing landfill capacity by recovering landfilled waste by landfill mining. In addition, it is analyzed that the lifespan is extended to 20 years, if the combustible waste of new inputting waste is sorted and combusted for energy recovery and incineration ash, incombustible waste, and soil matter are only reclaimed into the existing Cheongju landfill. It is expected that the methodology and parameters of this study will be used as basic data when resource recovery potential is analyzed for another case study of landfill mining.