• 대한소아치과학회지
• /
• 제23권4호
• /
• pp.867-886
• /
• 1996

The purpose of this study was to evaluate the shearbond strength and resin-dentin interface of three different dentinal bonding systems in primary and permanent teeth. Thirty extracted human primary molars and premolars, which were non-carious and free of obvious defect, were selected for this study. All specimens were divided into six groups with two groups allocated for each of the three dentinal bonding system(All-bond 2, Scotchbond Multi-Purpose, Gluma bonding system). After completion of bonding composite to dentin using each tested dentin bonding system, bond strength measurement and histological observation were performed. The results are as follows: 1. All-bond 2 and Scotchbond Multi-Purpose, A good quality hybrid layer was identified, the morphology of which could be equated with the zone of H-E and Brown-Brenn staining. In Gluma bonding system, hybrid layer was very thin, and separated from the solid polymer. 2. All-bond 2 had the highest mean shearbond strength, followed by Scotchbond Multi-Purpose and Gluma bonding system in both primary and permanent teeth. There was no statistically significant difference between All-bond 2 and Scotchbond Multi-Purpose. Statistically significant difference could be found between Gluma bonding system and the other two groups(p<0.05). 3. The fracture patterns observed were mainly the mixture of adhesive failure and dentin dettachment pattern in All-bond 2 and Scotchbond Multi-Purpose while adhesive failure prevailed in Gluma bonding system.

• Restorative Dentistry and Endodontics
• /
• 제28권5호
• /
• pp.378-384
• /
• 2003

This study evaluated the influence of a desensitizer(MS coat) on microtensile bond strength of different adhesives:a three-step adhesive(All-Bond 2), a two-step adhesive(Single Bond), a one-step adhesive(One-up Bond F). Non-caries extracted human molars were used. Dentin surface was obtained by horizontal section on mid-portion of crown using a water-cooled low speed diamond saw. Teeth were randomly divided into 6 group. AMO(MS coat + All Bond), SMO(MS coat + Single Bond)- and OMO(MS coat + One-up Bond F)-dentin surface were treated with 17% EDTA before bonded adhesive. AMX-, SMX- and OMX-dentin surface were bonded with All-Bond 2, Single Bond and One-up Bond F, respectively. with no previous treatment with MS coat and 17% EDTA. About 1cm high resin composite($Z-250^{TM}$) were incrementally build-up on the treated surface. The specimens for the microtensile test were serially sectioned perpendicular to the adhesive layer to obtain $0.7{\times}0.7mm$ sticks. 30 sticks were prepared from each group. After that. tensile bond strength for each stick was measured with Microtensile Tester at a 1mm/min crosshead speed. Fractured dentin surfaces were observed under the SEM. The results were statistically analysed by using a One-way ANOVA and Tukey's test(p<0.05). Value in MPa were: $AMO-44.35{\pm}13.21;{\;}SMO-39.35{\pm}13.32;{\;}OMO-31.07{\pm}10.25;{\;}AMX-49.22{\pm}16.38;{\;}SMX-56.02{\pm}13.35;{\;}OMX-72.93{\pm}16.19$. Application of MS coat reduced microtensile bond strengths of both Single Bond and One-up Bond F, whereas microtensile bond strengths of All-Bond 2 were not affected significantly.

• Restorative Dentistry and Endodontics
• /
• 제30권6호
• /
• pp.493-504
• /
• 2005

본 연구는 상아질 접착제와 레진 시멘트의 적합성 여부를 알아보고자 시행하였다. 발거한 제3대구치의 상아질 표면을 노출시킨 후 Tescera ATL 복합레진 시편을 상아질 접착제 [All Bond 2 (Bisco), Clearfil SE Bond (Kuraray), Adper Prompt L-POP (3M), One-Up Bond F (Tokuyama)]와 레진시멘트 [Choice (Bisco), Panavia F (Kuraray), RelyX ARC (3M), Bistite II DC (Tokuyama)]로 접착하고 미세인장 결합강도 및 주사전자 현미경 관찰을 시행한 결론은 다음과 같다. 1. Clearfil SE Bond와 All-Bond 2가 Prompt L-Pop과 One-Up Bond F 보다 높은 미세인장 결합강도를 보였다(p<0.05). 2. Clearfil SE Bond와 All-Bond 2 사용시 1-step 상아질 접착제보다 혼성층이 두껍고 레진 tag가 길었다.

• Restorative Dentistry and Endodontics
• /
• 제25권4호
• /
• pp.527-535
• /
• 2000

The purpose of this study was to evaluate effects of smear layer and dentin primers on the sealing ability of root canals. 126 extracted human teeth with single, straight canals and mature apices were used. The Samples were first classified into six groups as follows: presence of smear layer; absence of smear layer; Scotchbond Bond Multi-Purpose; All Bond 2; Mac Bond 2; Clearfil Liner Bond 2. A Positive control was also established. All teeth except the control group were then obturated with thermoplasticized gutta-percha and AH26. Electrochemical and dye penetration technique were later used to evaluate the degree of micro leakage through the root canal. Seventy teeth were then immersed in a 1% potassium chloride solution and An external power supply(DC 10 V) was then applied to the circuit for the electrochemical microleakage test. The degree of Microleakage was determined over period of 28 days before being evaluated. In total, 48 teeth were submitted to the dye infiltration technique. All specimen were suspended in 2% methylene blue dye for 1 week before being longitudinally split. The degree of dye infiltration was measured under a stereo microscope at ${\times}10$ magnification and evaluated. The results were as follows: 1. Apical microleakage increased throughout the test period in all group and one group having a smear layer showed a dramatic increase under electrochemical test (p<0.05). In the group having smear layer, the degree of apical microleakage was the highest, and the micro leakage was much higher than in the smear layer removed group in electrochemical test (p<0.05). Scotchbond Multi-Purpose, All Bond 2, Mac Bond 2 and Clearfil Liner Bond 2 showed lower micro leakage than one group having smear layer. The All Bond 2 and Clearfil Liner Bond 2 treated groups showed the lowest microleakage in electrochemical test (p<0.05). 2. There was no significant difference between the experimental groups in dye penetration technique. These results suggested that the removal of the smear layer from root canal and concomitantly the application of dentin primer into root canal could improve the sealing ability of root canal obturation.

• Restorative Dentistry and Endodontics
• /
• 제27권3호
• /
• pp.299-309
• /
• 2002

The purposes of this study were to evaluate the microtensile bond strength of one-step adhesives accord ing to various dentin surface treatments and to observe the interface between resin(Z-100$^{TM}$) and dentin under SEM. In this study forty-five non-caries extracted human molars and three adhesive systems were used ; AlI-Bond 2(AB), One-Up Bond F(OU), AQ-Bond(AQ). ; In Group 1, 2, 3, AB was used and tooth surfaces were treated by smearing(S), ultrasonic cleansing(US), etching(E) respectively. In Group 4. 5, 6, One-Up Bond F was used and tooth surfaces were also treated as the same way above. In Groups 7, 8, 9, AQ Bond was used and tooth surfaces wet$.$e treated as the same way. Each specimen was prepared for microtensile bond testing, and were stored for 24hrs in 37$^{\circ}C$ distilled water. After that, microtensile bond strength for each specimen was measured. Specimens were fabricated to examine the failure patterns of interface between resin and dentin and observed under the SEM. The results were as follows ; 1. The results(mean$\pm$SD) of microtensile test were group 1, 25.69$\pm$4.31MPa; group 2, 40.93$\pm$10.94MPa; group 3, 47.65$\pm$8.85MPa； group 4, 35.98$\pm$9.14MPa； group 5, 39.66$\pm$8.45MPa; group 6, 43.26$\pm$13.01MPa; group 7, 25.07$\pm$4.2MPa；group 8, 30.4$\pm$4.74MPa；group 9, 33.61$\pm$7.88MPa. 2. One-Up Bond F was showed the highest value of 36.98$\pm$9.14MPa in dentin surface treatment with smearing, and there were significant differences to the other groups (p<0.05). 3. All-Bond 2 was showed the highest value of 40.93$\pm$10.94MPa in dentin surface treatment with ultra-sonic cleansing, but was no significant difference to One-Up Bond F(p>0.05) 4. All-Bond 2 was showed the highest value of 47.65$\pm$8.85MPa in dentin surface treatment with etch ing(10%phosphoric acid), and there were significant differences to the other groups(p<0.05). 5. All-Bond 2 was showed the highest value of 47.65$\pm$8.85MPa in dentin surface treatment according to manufacture's directions. but was no significant difference to One-Up Bond F(p>0.05). 6. AQ Bond was skewed the lowest microtensile bond strength with various dentin surface treatment, and the were significant differences to the other groups(p<0.05).

• 대한소아치과학회지
• /
• 제23권2호
• /
• pp.347-355
• /
• 1996

The purpose of this study was to compare the bond strengths of different kinds of glass ionomer cements (GIC), which is recently increasing the clinical application in the field of pediatric dentistry and measure the repaired bond strengths in order to examine the clinical applicabilty of partial repaired cases. By using one kind of the light cured type GIC and three kinds of the chemical cured type GIC, the bond strengths of the followings were compared : unrepaired group as control, repaired conditioning group, which was treated the repaired surface using 25% polyacrylic acid and repaired non-conditioning group without surface treatment. Three point bending test was performed under Universal Testing Machine in order to measure the compressive bond strengths. The results were as follows : 1. Light cured GIC had higher bond strength than chemical cured type GIC in both of repaired and unrepaired groups. 2. In repaired cases, all of the materials decreased the bond strength when compared to the control group. In the light cured type, the bond strength of repaired conditioning group decreased 31.6%, repaired non-conditioning group decreased 40.8%. In chemical cured types, the bond strength of repaired conditining group decreased 11.8%, repaired non-conditioning group decreased 20.9%. 3. All the materials, in the case of the chemical treatment on the repaired surface using 25% polyacrylic acid had higher bond strength than untreated but, lower than control group.

• 대한소아치과학회지
• /
• 제33권4호
• /
• pp.661-672
• /
• 2006

우치 60개를 준비하여 법랑질과 상아질에 대하여 각각 1군 AQ Bond, 2군 AQ Bond $Plus^{TM}$, 3군 Single $Bond^{TM}$로 설정하고, 군당 10개씩 배정하였고, 군당 혼화층 관찰에 5개와 resin tag 관찰을 위해 5개씩 배정하였다. 준비된 우치의 법랑질과 상아질을 노출시킨 후 제조사의 지시에 따라 표면을 처리하고, 내경 3mm의 폴리에틸렌 튜브를 이용하여 $Z-250^{TM}$ 복합레진 접착을 시행하였다. 100% 습윤 상태에서 24시간동안 보관 후 $5^{\circ}C$와 $55^{\circ}C$ 조건하에서 500회 열순환을 시행하였다. 만능시험기를 분당 cross head speed 5mm 속도로 설정하고 100kg F load cell을 사용하여 전단결합강도를 측정하고 파절된 시편들을 수거하여 주사전자현미경으로 파절면을 관찰하였다. 혼화층과 resin tag 관찰을 위하여 상아질 접착면에 대해 수직으로 절단하고 인산과 질산으로 처리한 후 주사전자현미경으로 관찰하였다. 이상의 결과를 토대로 행동 조절에 어려움이 많은 소아 환자의 복합레진 수복시 적용 과정 및 시간 단축이 장점으로 부각되고 있는 all-in-one system의 임상 적용 가능성을 평가하고 다음과 같은 결론을 얻었다. 1. 전단 결합 강도 측정결과 1군, 2군 간에는 유의차가 없었으나, 3군이 1군과 2군에 비해 높은 전단 결합 강도를 보였으며 통계학적 유의차를 보였다 (p<0.05). 2. 파절 양상 관찰 결과 1군과 2군의 법랑질과 상아질 모두에서 그리고 3군의 상아질에서 주로 adhesive fracture 양상을 보였으며, 3군 법랑질에서 각각 cohesive와 adhesive fracture가 균등한 분포를 보였다. 3. 주사 전자 현미경 소견에서 1군과 2군은 resin tag형성이 매우 미약하고 불규칙한 양상을 보인 반면, 3군에서는 비교적 긴밀하게 형성된 resin tag이 관찰되었으며 resin tag의 표면에 형성된 뚜렷한 측부 가지들도 발견되었다.

• Bulletin of the Korean Chemical Society
• /
• 제23권2호
• /
• pp.215-220
• /
• 2002

The structures of 1-fluorosilatrane and the silatranyl cation were calculated by Hartree-Fock (HF), Mofller-Plesset second order (MP2), and various density functional theory (DFT) methods using many different basis sets, demonstrating that the Si-N bonds in two species are quite different. The N${\rightarrow}$Si bond distance of 1-fluorosilatrane from the hybrid DFT calculations $({\sim}2.32{\AA})$ using the Perdew-Wang correlation functional agrees with the gas phase experimental value $(2.324{\AA})$, while other functionals yield larger distances. The MP2 bond distance (2.287${\AA}$ with 6-311$G^{\ast}$) is shorter, and the HF one (2.544 ${\AA}$ with 6-311$G^{\ast}$) larger than those of DFT calculations. The MP2 bond distance is in good agreement with experiment indicating that the electron correlations are crucial for the correct description of the N${\rightarrow}$Si interaction. The silatranyl cation is a stable local minimum on the potential energy surface in all methods employed suggesting that the cation could be a reaction intermediate. The Si-N bond length for the cation is about 1.87 ${\AA}$ for all calculations tested implying that the Si-N bond is mainly conventional. Bonding characteristics of the Si-N bond in two species derived from the natural bond orbital analysis support the above argument based on calculated bond lengths.

• 대한치과기공학회지
• /
• 제7권1호
• /
• pp.19-25
• /
• 1985

In oder to compare and measure bond strength of ceramometal system with use of ceramco porcelain powder including SnO2 and uni metal, Rexillium III, Vera Bond as non precious alloys manufactured for porecelain-metal restorations. Total 24 test sample were constructed. All Test sample were measured with a Mitutoyo micrometer graduated to 0.01mm. It is as follows measured of thickness 3.3mm(metal : 1.1mm, porcelain: 2.2mm), width 12mm, length 30mm(porcelain 12mm x 12mm), Compared maximum bending stress test. The results obtained were as follows: 1. Bond strength of each metal with ceramco porcelain powder showed statistical significance.(P<0.05) 2. Vera Bond and uni metal, uni metal and Rexillium III revealed no statistical Significance.(P>0.05) Vera Bond and Rexillium III showed statistical significance.(P<0.05) 3. The order of maximum bending stress was Rexillium III, uni metal, vera Bond. The order of bond strength ratio making bending stress was Vera bond, uni metal, Rexillium III.

• 대한소아치과학회지
• /
• 제34권4호
• /
• pp.560-568
• /
• 2007

유치 60개를 준비하였으며, 사용된 접착 시스템은 AQ Bond $Plus^{TM}$, G $Bond^{TM}$, Single $Bond^{TM}$였다. 유치의 법랑질과 상아질을 노출시킨 후 제조사의 지시에 따라 접착 레진을 적용한 후, 내경 1.7 mm의 폴리에틸렌 튜브를 이용하여 Z-$250^{TM}$ 복합레진을 수복하였다. 100% 습윤 상태에서 24시간동안 보관 후 $5^{\circ}C$와 $55^{\circ}C$ 조건하에서 500회 열순환을 시행 후 만능시험기로 전단결합강도를 측정하였다. Resin tag 관찰을 위하여 상아질 접착면에 대해 수직으로 절단하고 인산과 질산으로 처리하여 치질을 용해시킨 후 주사 전자 현미경으로 관찰한 결과 다음과 같은 결론을 얻었다. 1. 유치 법랑질에서 측정된 전단 결합 강도는 AQ Bond $Plus^{TM}$에서 $1.04\;{\pm}\;0.13\;MPa$, G $Bond^{TM}$에서 $1.23\;{\pm}\;0.35\;MPa$, Single $Bond^{TM}$에서 $1.28\;{\pm}\;0.50\;MPa$이었으며, 세 군 간의 유의차는 없었다. 2. 유치 상아질에서의 전단 결합 강도는 AQ Bond $Plus^{TM}$는 $1.15\;{\pm}\;0.37\;MPa$, G $Bond^{TM}$는 $1.69\;{\pm}\;0.74\;MPa$ 그리고 Single $Bond^{TM}$는 $0.56\;{\pm}\;0.11\;MPa$로 나타났으며, AQ Bond $Plus^{TM}$와 G $Bond^{TM}$ 간에는 통계학적 유의차가 없었으나(p>0.05), AQ Bond $Plus^{TM}$와 Single $Bond^{TM}$, G $Bond^{TM}$과 Single $Bond^{TM}$ 간에는 통계학적 유의차를 보였다. 3. 주사 전자 현미경 소견에서 AQ Bond $Plus^{TM}$와 G $Bond^{TM}$는 resin tag 형성이 매우 미약하고 짧은 양상을 보인 반면, Single $Bond^{TM}$에서는 길게 형성된 resin tag가 관찰되었으며 resin tag의 표면에 불규칙하게 형성된 측부가지들이 관찰되었다.