• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.3
• /
• pp.244-250
• /
• 2023

In this paper, mortar mixed with tapioca starch was manufactured to evaluate the effect of tapioca starch on mortar, through evaluating the quality characteristics of mortar, the impact of tapioca starch on improving the performance and basic quality of mortar was examined. Tapioca starch tended to decrease flow by increasing the viscosity of the dough consistency of fresh mortar, which tended to reduce flow, and decreased by about 10 % as the tapioca starch mixing ratio increased by 0.025 %. In addition, the effect of tapioca starch on the compressive strength of mortar was at the same level regardless of the tapioca starch mixture at 28 days of age. However, at an early age of 3 days, the speed of compressive strength development was accelerated by mix ing tapioca starch. In addition, the effect of tapioca starch on the compressive strength of mortar was at the same level regardless of the tapioca starch mixture at 28 days of age. However, at an early age of 3 days, the speed of compressive strength development was accelerated by mixing tapioca starch. The speed of strength development improved by about 20 % when mixing 0.050 % tapioca starch. The adhesion strength improved by about 60 % when mixing 0.050 % tapioca starch, and the final shrinkage in length change decreased by 5 %.

• Composites Research
• /
• v.36 no.6
• /
• pp.441-447
• /
• 2023

Recently, as demand for high-strength, lightweight materials has increased, there has been great interest in joining with metals. In the case of mechanical bonding, such as bolting and riveting, chemical bonding using adhesives is attracting attention as stress concentration, cracks, and peeling occur. In this paper, surface treatment was performed to improve the adhesive strength, and the change in adhesive strength was analyzed. For the adhesive strength test were conducted with Carbon Fiber Reinforced Plastic(CFRP), CR340(Steel), and Al6061(Aluminum), and laser and plasma surface treatment were used. After plasma surface treatment, the adhesive strength improved by 7.3% and 39.2% in CFRP-CR340 and CFRP-Al6061, respectively. CR340-Al6061 was improved by 56.2% in laser surface treatment. Surface free energy(SFE) was measured by contact angle after plasma treatment, and it is thought that the adhesion strength was improved by minimizing damage through a chemical reaction mechanism. For laser surface treatment, it is thought that creates a rough bonding surface and improves adhesive strength due to the mechanical interlocking effect. Therefore, surface treatment is effect to improve adhesive strength, and based on this paper, the long-term fatigue test will be conducted to prevent fatigue failure, which is a representative cause of actual structural damage.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.412-419
• /
• 2023

Anion exchange membrane electrolysis is considered a promising next-generation hydrogen production technology that can produce low-cost, clean hydrogen. However, anion exchange membrane electrolysis technology is in its early stages of development and requires intensive research on electrodes, which are a key component of the catalyst-system interface. In this study, we optimized the pressure conditions of the hot-pressing process to manufacture cobalt oxide electrodes for the development of a high uniformity and high adhesion electrode production process for the oxygen evolution reaction. As the pressure increased, the reduction of pores within the electrode and increased densification of catalytic particles led to the formation of a uniform electrode surface. The cobalt oxide electrode optimized for pressure conditions exhibited improved catalytic activity and durability. The optimized electrode was used as the anode in an AEMWE single cell, exhibiting a current density of 1.53 A cm^-2 at a cell voltage of 1.85 V. In a durability test conducted for 100 h at a constant current density of 500 mA cm^-2, it demonstrated excellent durability with a low degradation rate of 15.9 mV kh^-1, maintaining 99% of its initial performance.

• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.559-571
• /
• 2017

This study was conducted to determine the adhesive performances of plywoods affected by layering direction and the amounts of thermoplastic films. The face and back layers of veneer were hardwood species (Mixed light hardwood) and core layer veneer was radiata pine (Pinus radiata D. Don). Thermoplastic film used as adhesive were polypropylene (PP) film and polyethylene (PE) film. Thermal analysis and tensile strength were investigated on each films. As a result, the melting temperature of PP and PE films were $163.4^{\circ}C$ and $109.7^{\circ}C$, respectively, and the crystallization temperature were $98.9^{\circ}C$ and $93.6^{\circ}C$, respectively. Tensile strength and elongation of each films appeared higher on the width direction than length direction. Considering the characteristics of the thermoplastic films, the test for the amount of film used was carried out by layering film to the target thickness on veneer. The effecting of layering direction of film on plywood manufacturing was conducted by laminating in the length and width directions of the film according to the grain direction of veneer. Tensile-shear strength of plywood in wet condition was satisfied with the quality standard (0.7 MPa) of KS F 3101 when the film was used over 0.05 mm of PP film and over 0.10 mm of PE film. Tensile-shear strength of plywood after cyclic boiling exceeded the KS standard when PP film was used 0.20 mm thickness. Furthermore, higher bonding strength was observed on a plywood made with width direction of film according to grain direction of veneer than that of length direction of film. Based on microscopic analysis of the surface and bonding line of plywood, interlocking between veneers by penetration of a thermoplastic film into inner and cracks were observed.

• Clean Technology
• /
• v.24 no.2
• /
• pp.127-134
• /
• 2018

To reduce the environmental pollution by $NO_x$ from ship engine, International maritime organization (IMO) announced Tier III regulation, which is the emmision regulation of ship's exhaust gas in Emission control area (ECA). Selective catalytic reduction (SCR) process is the most commercial $De-NO_x$ system in order to meet the requirement of Tier III regulation. In generally, commercial ceramic honeycomb SCR catalyst has been installed in SCR reactor inside marine vessel engine. However, the ceramic honeycomb SCR catalyst has some serious issues such as low strength and easy destroution at high velocity of exhaust gas from the marine engine. For these reasons, we design to metallic structured catalyst in order to compensate the defects of the ceramic honeycomb catalyst for applying marine SCR system. Especially, metallic structured catalyst has many advantages such as robustness, compactness, lightness, and high thermal conductivity etc. In this study, in order to support catalyst on metal substrate, coating slurry is prepared by changing binder. we successfully fabricate the metallic structured catalyst with strong adhesion by coating, drying, and calcination process. And we carry out the SCR performance and durability such as sonication and dropping test for the prepared samples. The MFC01 shows above 95% of $NO_x$ conversion and much more robust and more stable compared to the commercial honeycomb catalyst. Based on the evaluation of characterization and performance test, we confirm that the proposed metallic structured catalyst in this study has high efficient and durability. Therefore, we suggest that the metallic structured catalyst may be a good alternative as a new type of SCR catalyst for marine SCR system.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.31 no.2A
• /
• pp.129-136
• /
• 2011

Recently studies on functional concrete with a photocatalytic material such as $TiO_2$ have actively been carried out in order to remove air pollutants. The absorbtion of $TiO_2$ from those studies is applied by it being directly mixed into concrete or by suspension coated on the surface. When it comes to the effectiveness, the former process is less than that of the latter compared with the $TiO_2$ use. As a result, the direct coating of $TiO_2$ on materials' surface is more used for effectiveness. The Surface spread of it needs to have a more than $400^{\circ}C$ heat treat done to stimulate the activation and adhesion of photocatalysis. Heat treat consequently leads hydration products in concrete to be dehydrated and shrunk and is the cause of cracking. The study produces $TiO_2$ used Sol-gel method which enables it to be coated with a low temperature treat, applies it to pearlite using Lightweight Aggregate Concrete fixed with a low temperature treat and evaluates the spread performance of it. In addition to this, the size of pearlite is divided into two types: One is 2.5 mm to 5.0 mm and the other is more than 5.0 mm for the benefit of finding out the removal characteristics of $CH_3CHO$ whether they are affected by pearlite size, mixing method and ratio with $TiO_2$ and elapsed time. The result of this experiment shows that although $TiO_2$ produced by Sol-gel method is treated with 120 temperature, it maintains a high spread rate on the XRF(X ray Florescence) quantitative analysis which ranks $TiO_2$ 38 percent, $SiO_2$ 29 percent and CaO 18 percent. In the size of perlite from 2.5 mm to 5.0 mm, the removal characteristic of $CH_3CHO$ from a low temperature heated Lightweight concrete appears 20 percent higher when $TiO_2$ with Sol-gel method is spreaded on the 7 percent of surface. In other words, the removal rate is 94 percent compared with the 72 percent where $TiO_2$ is mixed in 10 percent surface. In more than 5.0 mm sized perlite, the removal rate of $CH_3CHO$, when $TiO_2$ is mixed with 10 percent, is 69 percent, which is similar with that of the previous case. It suggests that the size of pearlite has little effects on the removal rate of $CH_3CHO$. In terms of Elapsed time, the removal characteristic seems apparent at the early stage, where the average removal rate for the first 10 hours takes up 84 percent compared with that of 20 hours.

• Molecules and Cells
• /
• v.38 no.3
• /
• pp.210-220
• /
• 2015

Athletic performance is an important criteria used for the selection of superior horses. However, little is known about exercise-related epigenetic processes in the horse. DNA methylation is a key mechanism for regulating gene expression in response to environmental changes. We carried out comparative genomic analysis of genome-wide DNA methylation profiles in the blood samples of two different thoroughbred horses before and after exercise by methylated-DNA immunoprecipitation sequencing (MeDIP-Seq). Differentially methylated regions (DMRs) in the pre-and post-exercise blood samples of superior and inferior horses were identified. Exercise altered the methylation patterns. After 30 min of exercise, 596 genes were hypomethy-lated and 715 genes were hypermethylated in the superior horse, whereas in the inferior horse, 868 genes were hypomethylated and 794 genes were hypermethylated. These genes were analyzed based on gene ontology (GO) annotations and the exercise-related pathway patterns in the two horses were compared. After exercise, gene regions related to cell division and adhesion were hypermethylated in the superior horse, whereas regions related to cell signaling and transport were hypermethylated in the inferior horse. Analysis of the distribution of methylated CpG islands confirmed the hypomethylation in the gene-body methylation regions after exercise. The methylation patterns of transposable elements also changed after exercise. Long interspersed nuclear elements (LINEs) showed abundance of DMRs. Collectively, our results serve as a basis to study exercise-based reprogramming of epigenetic traits.

• Journal of Embryo Transfer
• /
• v.21 no.3
• /
• pp.217-223
• /
• 2006

This study was carried out principally to obtain the basic data for the improvement of the reproductive performance and production using plasma progesterone assay and ultrasonography in dairy cow. The results obtained from this studies were as follows. The results of reproductive examination in 85,983 cows were ovarian diseases 40,399 (47.0%), uterine diseases 11,912 (13.9%), pregnancy or pregnant failures 26,587 (30.9%), adhesion of reproductive tracts 172 (0.2%), freemartin 8 (0.01%), and others 6,905 (8.3%), respectively. The treatment status of reproductive dysfunction in 30,241 cows were silent heat or error of estrus detection 14,909 (49.3%), follicular cysts 3,750 (12.4%), luteal cysts 907 (3.0%), inactive ovaries 665 (2.2%), granulosa cell tumor of ovary 3 (0.01%) and endometritis 6,986 (23.1%), respectively. The indices of reproductive efficiency after the periodical examination of reproductive status were as follows; the mean intercalving inteual was reduced from 475 days at the first examination to 381 days at the last examination of reproductive status, the mean interval calving to conception was reduced from 186 to 98 days, the mean interval calving to first service was reduced from 106 to 66 days, the cows showing heat by 60 days postpartum were increased from 32 to 90%, the mean conception rate to first service was increased from 42 to 64%, and the mean service per conception was reduced from 2.6 to 1.8 times, respectively.

• Sijohaknonchong
• /
• v.44
• /
• pp.7-28
• /
• 2016

Music was made popular through the modern mass media. Nonetheless, if a period of high standard performances and appreciation by a minority of culture connoisseurs can be qualified with the expression "gentrification of culture", then a period when anyone can access culture through the mass media can be qualified with the terms "popularization of culture" and in this period the reorganization of performance culture can only be driven by the public. In fact, the Jabga, which is a type of traditional song that received strong public adhesion by means of phonograph records and radio broadcasts at the time, stands as a typical example to it. Gagok and Sijo up until the 1920s and even the 1930s are believed to engage actively in the changing media environment and the new modes of music enjoyment and transmission. The Album recording of faster rhythm music and the inclusion of the Sijo, Jabga, and folk songs in one broadcast programme can be seen as reflecting such an effort. However, it can only be hard for the Sijo and Gagok to challenge the predominance of the Jabga which made its lyrics more popular and the new songs written in accordance with the new media environment. Until the 1930s in this changing environment of music enjoyment, Gagok and Sijo performers rather sought to distinguish themselves from the existing popular song style by reproducing traditional forms. The album recording and broadcasting of Lee Wangjik Aakbu, the beginnings of local singers, the participation of male performers not only contributed to the diversification the enjoyment culture of songs and sijo, but also made the 'difference in standard' with the popular songs even more salient.

• Journal of the Korean Society of Radiology
• /
• v.17 no.3
• /
• pp.441-447
• /
• 2023

Lead(Pb), which is currently mainly used for shielding purposes in the medical radiation, has excellent radiation shielding functions, but is continuously exposed to radiation directly or indirectly due to the harmfulness of lead itself to the human body and the inconvenience caused by its heavy weight. Research on shielding materials that are human-friendly, lightweight, and convenient to use that can block risks and replace lead is continuously being conducted. In this study, based on the commonly used polyethylene terephthalate (PET) film and the fabric material used in actual radiation protective clothing, a multi-layer thin film was realized through sputtering and vacuum deposition of bismuth, tungsten, and tin, which are metal materials that can shield radiation. Thus, a shielding film was produced and its applicability as a radiation shielding material was evaluated. The radiation shielding film was manufactured by establishing the optimized conditions for each shielding material while controlling the applied voltage, roll driving speed, and gas supply amount to manufacture the shielding film. The adhesion between the parent material and the shielding metal thin film was confirmed by Cross-cut 100/100, and the stability of the thin film was confirmed through a hot water test for 1 hour to measure the change of the thin film over time. The shielding performance of the finally realized shielding film was measured by the Korea association for radiation application (KARA), and the test conditions (inverse wide beam, tube voltage 50 kV, half layer 1.828 mmAl) were set to obtain an attenuation ratio of 16.4 (initial value 0.300 mGy/s, measured value 0.018 mGy/s) and damping ratio 4.31 (initial value 0.300 mGy/s, measured value 0.069 mGy/s) were obtained. by securing process efficiency for future commercialization, light and shielding films and fabrics were used to lay the foundation for the application of films to radiation protective clothing or construction materials with shielding functions.