• Transactions on Electrical and Electronic Materials
• /
• v.12 no.5
• /
• pp.213-217
• /
• 2011

The nonlinear electrical properties and degradation behavior against an impulse-current of 400 A in the ZnO-$Pr_6O_{11}$-CoO-$Cr_2O_3$-$Y_2O_3$-$Er_2O_3$ (ZPCCYE) varistors were investigated with different $Y_2O_3/Er_2O_3$ ratios. The $Y_2O_3/Er_2O_3$ mole ratio has a significant effect on nonlinear electrical properties and impulse degradation behavior of the ZPCCYE varistors. The varistors added with $Y_2O_3/Er_2O_3$ = 0.5/0.5 exhibited the best nonlinear properties with 39 in nonlinear coefficient (${\alpha}$) and the best clamp characteristics, in which the clamping voltage ratio (K) was in the range of K = 1.62-2.18 at an impulse-current of 1-50 A. The varistors added with $Y_2O_3/Er_2O_3$ = 0.25/0.5 exhibited the best electrical stability, with $%{\Delta}E_{1mA/cm^2}$=-5.6%, $%{\Delta}{\alpha}$ = 6.7%, and $%{\Delta}J_L$ = -14.6% against an impulse-current of 400 A. On the contrary, the varistors added with $Y_2O_3/Er_2O_3$ = 0.5/0.5 were destroyed applying an impulse-current of 400 A.

• Journal of the Korean Ceramic Society
• /
• v.23 no.6
• /
• pp.37-44
• /
• 1986

Yttria-antimonia-stabilized zirconia was investigated with respect to the amount of $Sb_2O_3$ addition in the range of 0.5~5mole% to the base composition of $(ZrO)_{0.92}(Y_2O_3)_{0.08}$ The sinterbility modulus of rupture Vickers hardness evaporation of components phase form-tion and mcicrostructure were evaluated with antimonia content. Also two probe A. C conductivity measurement was subjected to all specimens and the best results are achieved with 1mol% $Sb_2O_3$ as a sinter agent and relative density of~98% obtained at 140$0^{\circ}C$ and this composition has a maximum electrical conductivity due to the possible substition of $Sb^{3+}$ for $Zr^{4+}$ site. The effect of $Sb_2O_3$ on the electrical conductivity of th bulk and the grain boundaries has on investigated using frequency dispersion analysis (5~106 Hz) Antimonia addition has a negative in-fluence on both the bulk and the grain boundary conductivity except for a 1 mon% addition. The additive antimonia has improve a modulus of rupture to 60~MPa due to metastable-tetragonal phase apparence and decrease the hardness with increasing the $Sb_2O_3$ content.

• Korean Journal of Materials Research
• /
• v.2 no.4
• /
• pp.248-256
• /
• 1992

This paper has reviewed some of the basic principles that underlie the field of defect chemistry in simple ATi$O_3$(A=Ca, Sr, Ba) perovskites. Frenkel defects in perovskite structure is very much unlikely, and Schottky defects and intrinsic electronic defects in undoped materials are negligibly small compared with background acceptor impurities. The electrical properties of perovskite ceramics are dependent on the aliovalent impurities. Since perovskite structure is a ternary system, the stoiohiometry between cations as well as cation-anion ratio will affect defect structure and electrical properties. BaTi$O_3$and SrTi$O_3$show a limited deviation from the cation stoichiometry while CaTi$O_3$has significant excess CaO and Ti$O_2$solubility.

• Nuclear Engineering and Technology
• /
• v.52 no.9
• /
• pp.2078-2084
• /
• 2020

Magnesium oxide (MgO) and Zinc oxide (ZnO) nanoparticles (NPs) have been successfully synthesized by solid-solid reaction method. The structural properties of ZnO and MgO NPs were studied using X-ray diffraction (XRD) and scanning electron microscopy (SEM). XRD results indicated a formation of pure MgO and ZnO NPs. The mean diameter values of the agglomerated particles were around to be 70 and 50 nm for MgO and ZnO NPs, respectively using SEM analysis. Further, a wide-range of nuclear radiation shielding investigation for gamma-ray and fast neutrons have been studied for Magnesium oxide (MgO) and Zinc oxide (ZnO) samples. FLUKA and Microshield codes have been employed for the determination of mass attenuation coefficients (μ_m) and transmission factors (TF) of Magnesium oxide (MgO) and Zinc oxide (ZnO) samples. The calculated values for mass attenuation coefficients (μ_m) were utilized to determine other vital shielding properties against gamma-ray radiation. Moreover, the results showed that Zinc oxide (ZnO) nanoparticles with the lowest diameter value as 50 nm had a satisfactory capacity in nuclear radiation shielding.

• Composites Research
• /
• v.13 no.6
• /
• pp.1-8
• /
• 2000

The fabrication Process of $Al_2O_{3p}$/AC8A composites by pressureless infiltration technique and the effects of additive Mg content and volume fraction of particulate reinforcement on mechanical and wear properties were investigated. It was found that the bending strength decreased with increasing volume fraction of $Al_2O_{3p}$ particles. Whereas hardness increased with volume fraction of $Al_2O_{3p}$ particles. The decrement of strength in case of high volume fraction of $Al_2O_{3p}$ particles was attributed to high porosity level. In terms of additive Mg content, $Al_2O_{3p}$/AC8A composites containing around 5~7wt% of additive Mg indicated the highest strength, and hardness values increased with additive Mg contents. Wear resistance of AC8A alloy were improved by reinforcement of $Al_2O_{3p}$ particles especially at high sliding velocity. Wear property of $Al_2O_{3p}$/AC8A composites and AC8A alloy exhibited different aspects. $Al_2O_{3p}$/AC8A composites indicated more wear loss than AC8A alloy at slow velocity region. However a transition point of wear loss was found at middle velocity region which shows the minimum wear loss and wear loss at high velocity region exhibited almost same value as at slow velocity region, whereas wear loss of AC8A alloy almost linearly increased with sliding velocity. It was found that $Al_2O_{3p}$/AC8A composites containing $Al_2O_{3p}$ volume fraction of 20% exhibited abrasive wear surface regardless of sliding velocity and $Al_2O_{3p}$/AC8A composites containing $Al_2O_{3p}$ volume fraction of 40% showed slightly adhesive wear surface at low sliding velocity, and it progressed to severe wear as increasing the sliding velocity.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.6
• /
• pp.683-689
• /
• 2004

The microstructure and electrical characteristics of A ∼ C's ZnO varistors fabricated according to variable sintering condition, which sintering temperature was 1130 $^{\circ}C$ and speeds of pusher were A: 2 mm/min, B: 4 mm/min, C: 6 mm/min, respectively, were investigated. The experimental results obtained from this study were summarized as follows: The sintering density of A ∼C's ZnO varistors sintered at 1130 $^{\circ}C$ were decreased by sintering keep time to shorten, such as A: 9hour, B: 4.5hour and C: 3hour. A's ZnO varistor exhibited good densification nearly 98 % of theory density. In the microstructure, A∼C's ZnO varistors fabricated variable sintering condition was consisted of ZnO grain(ZnO), spinel phase(Z $n_{2.33}$S $b_{0.67}$ $O_4$), Bi-rich phasc(B $i_2$ $O_3$), wholly. Varistor voltage of A∼C's ZnO varistors sintered at 1130 $^{\circ}C$ increased in order A