• Journal of IKEEE
• /
• v.22 no.1
• /
• pp.180-184
• /
• 2018

Gallium oxide ($Ga_2O_3$) and silicon carbide (SiC) are the material with the wide band gap ($Ga_2O_3-4.8{\sim}4.9eV$, SiC-3.3 eV). These electronic properties allow high blocking voltage. In this work, we investigated the characteristic of $Ga_2O_3$ and 4H-SiC vertical depletion-mode metal-oxide-semiconductor field-effect transistors. We demonstrated that the blocking voltage and on-resistance of vertical DMOSFET is dependent with structure. The structure of $Ga_2O_3$ and 4H-SiC vertical DMOSFET was designed by using a 2-dimensional device simulation (ATLAS, Silvaco Inc.). As a result, 4H-SiC and $Ga_2O_3$ vertical DMOSFET have similar blocking voltage ($Ga_2O_3-1380V$, SiC-1420 V) and then when gate voltage is low, $Ga_2O_3-DMOSFET$ has lower on-resistance than 4H-SiC-DMOSFET, however, when gate voltage is high, 4H-SiC-DMOSFET has lower on-resistance than $Ga_2O_3-DMOSFET$. Therefore, we concluded that the material of power device should be considered by the gate voltage.

• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.619-625
• /
• 2020

In this paper, we propose a TS-DMOSFET(Trench Shielded DMOSFET) structure in which P+ shielding region is formed in a deeper region than C-DMOSFET(Conventional DMOSFET) and S-DMOSFET(Shielded DMOSFET). Using TCAD simulation to compare the static characteristics of TS-DMOSFET with C- and S-DMOSFET. As for the structure proposed, the doping is followed by the source trench process. Despite the fact that it is a SiC material, this allows it to form a P+ shielding region in a deep area. Followed by completely suppressing the reach-through effect. As a result, when the breakdown voltage of the three structures is 3.3kV, the Ron of TS-DMOSFET is 9.7mΩ㎠. Thus, it is 68% and 54% smaller than the Ron of C-DMOSFET and S-DMOSFET respectively.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.63-63
• /
• 2009

In this work, we demonstrate 800V 4H-SiC power DMOSFETs with several structural alterations to observe static DC characteristics, such as a threshold voltage ($V_{TH}$) and a figure of merit ($V_B^2/R_{SP,ON}$). To optimize the static DC characteristics, we consider four design parameters; (a) the doping concentration ($N_{CSL}$) of current spreading layer (CSL) beneath the p-base region, (b) the thickness of p-base ($t_{BASE}$), (c) the doping concentration ($N_J$) and width ($W_J$) of a JFET region, (d) the doping concentration ($N_{EPI}$) and thickness ($t_{EPI}$) of epi-layer. Design parameters are optimized using 2D numerical simulations and the 4H-SiC DMOSFET structure results in high figure of merit ($V_B^2/R_{SP,ON}$>~$340MW/cm^2$) for a power MOSFET in $V_B{\sim}1200V$ range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.637-640
• /
• 2009

In this work, we demonstrate 800 V 4H-SiC power DMOSFETs with several structural alterations to obtain a low threshold voltage ($V_{TH}$) and a high figure of merit ($V_B\;^2/R_{SP,ON}$), To optimize the device performance, we consider four design parameters; (a) the doping concentration ($N_{CSL}$) of current spreading layer (CSL) beneath the p-base region, (b) the thickness of p-base ($t_{BASE}$), (c) the doping concentration ($N_J$) and width ($W_J$) of a JFET region, (d) the doping concentration ($N_{EPI}$) and thickness ($t_{EPI}$) of epi-layer. These parameters are optimized using 2D numerical simulation and the 4H-SiC DMOSFET structure results in a threshold voltage ($V_{TH}$) below $^{\sim}$3.8 V, and high figure of merit ($V_B\;^2/R_{SP,ON}$>$^{\sim}$200 $MW/cm^2$) for a power MOSFET in $V_B\;^{\sim}$800 V range.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.832-838
• /
• 2019

In this paper, 4H-SiC MOSFET, the next generation power semiconductor device, was studied. In particular, Semi-SJ MOSFET structures with improved electrical characteristics than conventional DMOSFET structures were proposed in the class of 3300V, and static characteristics of conventional and proposed structures were compared and analyzed through TCAD simulations. Semi-SuperJunction MOSFET structure is partly structure that introduces SuperJunction, improves Electric field distribution through the two-dimensional depletion effect, and increases breakdown voltage. Benefit from the improvement of breakdown voltage, which can improve the on resistance as high doping is possible. The proposed structure has a slight reduction in breakdown voltage, but has an 80% decrease in on resistance compared to the conventional DMOSFET structure, and a 44% decrease in on resistance compared to the Current Spreading Layer(CSL) structure that improves the conventional DMOSFET structure.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.35-36
• /
• 2009

In this work, we demonstrate 800V 4H-SiC power DMOSFETs with several structural alterations to obtain a low threshold voltage ($V_{TH}$) and a high figure of merit ($V_B^2/R_{SP,ON}$). To optimize the device performance, we consider four design parameters; (a) the doping concentration ($N_{CSL}$) of current spreading layer (CSL) beneath the p-base region, (b) the thickness of p-base ($t_{BASE}$), (c) the doping concentration ($N_J$) and width ($W_J$) of a JFET region, (d) the doping concentration ($N_{EPI}$) and thickness ($t_{EPI}$) of epi-layer. These parameters are optimized using 2D numerical simulation and the 4H-SiC DMOSFET structure results in a threshold voltage ($V_{TH}$) below ~3.8V, and high figure of merit ($V_B^2/R_{SP,ON}$>${\sim}200MW/cm^2$) for a power MOSFET in $V_B$-800V range.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.352-352
• /
• 2010

Silicon Carbide (SiC) power device possesses attractive features, such as high breakdown voltage, high-speed switching capability, and high temperature operation. In general, device design has a significant effect on the switching characteristics. In this paper, we report the effect of the P-base doping concentration ($N_{PBASE}$) on the transient characteristics of 4H-SiC DMOSFETs. By reducing $N_{PBASE}$, switching time also decreases, primarily due to the lowered channel resistance. It is found that improvement of switching speed in 4H-SiC DMOSFETs is essential to reduce the and channel resistance. Therefore, accurate modeling of the operating conditions are essential for the optimization of superior switching performance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.131-131
• /
• 2009

Silicon Carbide (SiC) is a material with a wide bandgap (3.26eV), a high critical electric field (~2.3MV/cm), a and a high bulk electron mobility ($\sim900cm^2/Vs$). These electronic properties allow high breakdown voltage, high-speed switching capability, and high temperature operation compared to Si devices. Although various SiC DMOSFET structures have been reported so far for optimizing performances, the effect of channel dimension on the switching performance of SiC DMOSFETs has not been extensively examined. This paper studies different channel dimensons ($L_{CH}$ : $0.5{\mu}m$, $1\;{\mu}m$, $1.5\;{\mu}m$) and their effect on the the device transient characteristics. The key design parameters for SiC DMOSFETs have been optimized and a physics-based two-dimensional (2-D) mixed device and circuit simulator by Silvaco Inc. has been used to understand the relationship. with the switching characteristics. To investigate transient characteristic of the device, mixed-mode simulation has been performed, where the solution of the basic transport equations for the 2-D device structures is directly embedded into the solution procedure for the circuit equations. We observe an increase in the turn-on and turn-off time with increasing the channel length. The switching time in 4H-SiC DMOSFETs have been found to be seriously affected by the various intrinsic parasitic components, such as gate-source capacitance and channel resistance. The intrinsic parasitic components relate to the delay time required for the carrier transit from source to drain. Therefore, improvement of switching speed in 4H-SiC DMOSFETs is essential to reduce the gate-source capacitance and channel resistance.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.04b
• /
• pp.37-38
• /
• 2009

SiC power device possesses attractive features, such as high breakdown voltage, high-speed switching capability, and high temperature operation. In general, device design has a significant effect on the switching characteristics. It is known that in SiC power MOSFET, the JFET region width is one of the most important parameters. In this paper, we demonstrated that the switching performance of DMOSFET is dependent on the with width of the JFET region by using 2-D Mixed-mode simulations. The 4H-SiC DMOSFETs with a JFET region designed to block 800 V were optimized for minimum loss by adjusting the parameters of the n JFET region, CSL, and n-drift layer. It has been found that the JFET region reduces specific on-resistance and therefore the switching characteristics depend on the JFET region.

• Journal of Electrical Engineering and Technology
• /
• v.7 no.2
• /
• pp.236-239
• /
• 2012

In this paper, we study the transient characteristics of 4H-SiC DMOSFETs with different interface charges to improve the turn-on rising time. A physics-based two-dimensional mixed device and circuit simulator was used to understand the relationship between the switching characteristics and the physical device structures. As the $SiO_2$/SiC interface charge increases, the current density is reduced and the switching time is increased, which is due primarily to the lowered channel mobility. The result of the switching performance is shown as a function of the gate-to-source capacitance and the channel resistance. The results show that the switching performance of the 4H-SiC DMOSFET is sensitive to the channel resistance that is affected by the interface charge variations, which suggests that it is essential to reduce the interface charge densities in order to improve the switching speed in 4H-SiC DMOSFETs.