• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.458-458
• /
• 2013

We investigated a study on the thermal degradation of boron doped zinc-oxide (BZO) layer which used as a transparent conducting layer on the Cu (In1-xGax) Se2 (CIGS) based thin film solar cells. Devices were annealed under the temperature of $100^{\circ}C$ or 100 hours and then Hall measurement was carried out to characterize the parameters of mobility (${\mu}Hall$), resistivity (${\rho}$), conductivity (${\sigma}$) and sheet resistance (Rsh). The initial values of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh were $29.3cm^2$/$V{\cdot}s$, $2.1{\times}10^{-3}{\Omega}{\cdot}cm$, $476.4{\Omega}^{-1}{\cdot}cm^{-1}$ and $19.1{\Omega}$/${\Box}$ respectively. After the annealing process, the values were $4.5cm^2$/$V{\cdot}s$, $12.8{\times}10^{-3}{\Omega}{\cdot}cm$, $77.9{\Omega}^{-1}{\cdot}cm^{-1}$ and $116.6{\Omega}$/${\Box}$ respectively. We observed that ${\mu}Hall$ and ${\sigma}$ were decreased, and ${\rho}$ and Rsh were increased. In this study, BZO layer plays an important role of conducting path for electrons generated by incident light onthe CIGS absorption layer. Therefore, the degradation of BZO layer characterized by the parameters of ${\mu}Hall$, ${\rho}$, ${\sigma}$ and Rsh, affect to the cell efficiency.

• Current Photovoltaic Research
• /
• v.8 no.4
• /
• pp.129-133
• /
• 2020

It is very important to optimize the reflectance of incident light in solar modules for improving output power and reducing loss of cell-to-module (CTM). It is assumed that a higher reflectance backsheet may improve optical efficiency. However how much output power is related to optical properties by reflectance property of backsheets have not been revealed clearly yet. A total of 3 types of industrial backsheets with 3 type of industrial encapsulants (EVA or POE) were analyzed as fabricated mini modules used shingled cells. According to the type of backsheets, the difference between the highest and lowest average reflectance in the range of 400 nm to 1200 nm was found to be 13.08% by UV-visible spectroscopy. Also, when using the same encapsulant, the maximum gap value of the output power increase was measured by about 3.755 mW% (166.02 mW). The correlation between reflectance and output power was experimentally found by measuring the output property of the fabricated shingled mini modules.

• The Journal of the Acoustical Society of Korea
• /
• v.27 no.3
• /
• pp.129-139
• /
• 2008

The purpose of the present work is to derive the reflection and transmission coefficients of $S_0\;and\;A_0$ mode Lamb waves in relation to the geometry of a rectangular notch when the waves propagate across the notch in an elastic plate. Firstly, the excitable modes of the Lamb wave were analyzed with respect to the plate thickness. The scattering phenomena were divided into three independent processes according to the boundary shape of the notch and the direction of the wave propagation. Linear equations for each process were derived with corresponding free or continuous boundary conditions to analyze the scattered waves. By the rule of linear superposition, the waves scattered at each process were summed for each mode. Then the steady-state reflection and transmission coefficients of the scattered waves were determined so that the difference of energy flux between the incident and the scattered waves would remain within 4%.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.28 no.2
• /
• pp.73-80
• /
• 2016

To reduce the mechanical energy loss and to get the high energy efficiency, an apparatus of wave power generation inducing a consistent one way rotating motion from the wave reciprocation motions was developed and the hydraulic experiments for the real electric power production were conducted and the results were discussed. In the experiments for the shape of the buoyant tank, the efficiency of the fixed 9 cm diameter type enduring the wave plate weight was 14.6% and this was the best result for all shapes. But although the free sliding type was expected to represent a high efficiency, the experiments did not show a good result as 8.5% efficiency. Therefore, the shape of buoyant tank was decided as the fixed 9 cm diameter type in the next all tests. In the experiments for the various incident waves, when the water depth was 90 cm, the average efficiencies were measured as 3.9% in the 2nd gear, 4.9% in the 3rd gear, 4.9% in the 4th gear, 12.0% in the 5th gear, 10.0% in the 6th gear, 3.1% in the 7th gear, and 3.0% in the 8th gear. Also, when the water depth was 80 cm, the average efficiency was shown as 15.0% with 5th gear condition. Therefore the high average efficiency as 13.5% was given with 80~90 cm water depth and the 5th gear in the model.

• The Journal of Korea Robotics Society
• /
• v.3 no.4
• /
• pp.345-350
• /
• 2008

This study aims to propose the concept design of oil spill protection robot which can rapidly intervene to control the oil spillage situation at the sea. Taking into account the fact that a huge amount of oil is transported trans-continentally by oil tanker, none of industrialized countries are completely safe from the marine oil spill which results in social, economical and ecological damages to their communities. The employment of double hull-oil tanker, pipe line transporting can be most safe way. Yet complete prevention of oil spill is probably not realistic. Accordingly the alternative solution to control marine oil spill and minimize the damages caused by the incident using intelligent robot technology based on swarm control method is proposed. The main features of oil spill protection(OSP) robot is explained via following three perspectives. Firstly, from functional point of view, OSP robot system safely and efficiently replaces oil boom installation manually conducted by human workers with intelligent robot technology based on swarm control theory. For second, its modular architecture brings efficient storage of main components including oil boom and facilitates maintenance. For the last, its geometric form and shape enables whole system to be installed to helicopter, boat or oil tanker itself with ease and to rapidly deploy the units to the oil spill area.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2003.10a
• /
• pp.317-322
• /
• 2003

The Sectional and Spatial failure modes are discussed using the experimental data with long crest wave and multi-directional waves considering the failure modes occurring around the rubble-mound breakwater. The spatial & sectional stability and failure mode around the rubble-mound structures with construction progress can be summarized as follows: 1) The rubble mound structures at basic construction step was occurred serious failures when ${\xi}$ was about 6.5. 2) It was clarified that the failure modes at the round head of detached breakwater are classified as failure by plunging breaking on the slope, failure by direct incident wave force and failure by scouring at the toe of the detached break water. 3) The failure mode was found in the lower wave height than the design wave by the breaker depth effect. 4) The failure on the slope were also developed at the lee side of the round head because diffracted wave propagated into the behind area by grouping effect of multi-directional irregular wave.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.27 no.11
• /
• pp.679-685
• /
• 2014

For the measurements of surface shape milled using FIB (focused ion beam), the silicon bulk, $Si_3N_4/Si$, and Al/Si samples are used and observed the shapes milled from different sputtering rates, incident angles of $Ga^+$ ions bombardment, beam current, and target material. These conditions also can be influenced the sputtering rate, raster image, and milled shape. The fundamental ion-solid interactions of FIB milling are discussed and explained using TRIM programs (SRIM, TC, and T-dyn). The damaged layers caused by bombarding of $Ga^+$ ions were observed on the surface of target materials. The simulated results were shown a little bit deviation with the experimental data due to relatively small sputtering rate on the sample surface. The simulation results showed about 10.6% tolerance from the measured data at 200 pA. On the other hand, the improved analytical model of damaged layer was matched well with experimental XTEM (cross-sectional transmission electron microscopy) data.

• Journal of Satellite, Information and Communications
• /
• v.7 no.3
• /
• pp.54-57
• /
• 2012

Nematic liquid crystal (NLC) alignment effects on SiOF layers via ion-beam (IB) irradiation for four types of incident energy were successfully studied. The effect of fluorine addition on silicon oxide film properties as a function of $SiOF_4/O_2$ gas flow ration was investigated. The SiOF thin film exhibits good chemical and the thermal stability of the SiOF thin film were sustained as function of the NLC alignment until $200^{\circ}C$ Also, the response-time characteristics of aligned LCD based on SiOF film were studied.

• The Korean Journal of Emergency Medical Services
• /
• v.17 no.2
• /
• pp.65-76
• /
• 2013

Purpose : The purpose of this study was to provide an appropriated direction for fire service organizational management by analyzing the violence experiences and turnover intention of female 119 emergency medical technicians (119 EMT) in Korea. Methods : The questionaries were obtained from 415 female 119 EMT in Korea from April 27 to March 8 in 2009. The collected data were analyzed with SPSS WIN 19.0 program. Results : Female 119 EMTs experienced 94.9%-verbal insults, 57.1%-violence aggression, 62.89%- potential violence, 32.5%-physical assault. About 76.4% of the subjects experienced to feel shame about the verbal insults. They had a stress level (mean 5.47 out of 10) and about 41.2% was more than seven points. About 39.3% of the subjects responded turnover intention. Conclusion : We proposed the preventive program against violence as well as critical incident stress debriefing. These results are expected to be useful in making human resource management plans to lower turnover intention.

• Journal of The Korean Astronomical Society
• /
• v.33 no.3
• /
• pp.165-172
• /
• 2000

A baffle system for an airglow photometer, which will be on board the Korea Sounding Rocket-III(KSR-III), has been designed to suppress strong solar scattered lights from the atmosphere below the earth limb. Basic principles for designing a baffle system, such as determination of baffle dimensions, arrangement of vanes inside a baffle tube, and coating of surfaces, have been reviewed from the literature. By considering the constraints of the payload size of the KSR-III and the incident angle of solar light scattered from the earth limb, we first determined dimensions of a two-stage baffle tube for the airglow photometer. We then calculated positions and heights of vanes to prohibit diffusely reflected lights inside the baffle tube from entering into the photometer. In order to evaluate performance of the designed baffle system, we have developed a ray tracing program using a Monte Carlo method. The program computed attenuation factors of the baffle system on the order of $10^{-6}$ for angles larger than $10^{\circ}$, which satisfies the requirements of the KSR-III airglow experiment. We have also measured the attenuation factors for an engineering model of the baffle system with a simple collimating beam apparatus, and confirmed the attenuation factors up to about $10^{-4}$. Limitation of the apparatus does not allow to make more accurate measurements of the attenuation factors.