• 한국산업융합학회 논문집
• /
• 제26권4_2호
• /
• pp.629-637
• /
• 2023

This study aimed to evaluate the effect of post-curing equipment and time on the flexural strength of 3D printing resins produced by a liquid crystal display(LCD) printer. The three 3D printing resins(DENTCA Denture Teeth, DT; C&B 5.0 hybrid, CH; C&B Permanent A2, CP) were divided into four groups according to post-curing time(10 min and 30 min) and equipment with or without vacuum treatment. For the three-point flexural strength test and biaxial strength test were prepared by method according to ISO 10477, ISO 6872, respectively. Flexural strength was measured with universal testing machine. Comparison between post-curing time of each post-curing equipment was analyzed by independent sample t-test and Mann-Whitney U test(α=.05), and comparison between groups according to each 3D printing resin was performed by Kruskal-Wallis test and post-hoc by Bonferroni-Dunn test(α=.05). The flexural strength of the resin post-curing under vacuum was higher than that of the resin post-curing in air. In the comparison according to the post-curing time, in the case of the post-curing equipment without vacuum, the 30 minute curing time showed significantly higher flexural strength than the 10 minute curing time, except for the biaxial flexural strength of CH(P<.05). In the post-curing equipment with vacuum, the three-point flexural strength of all 3D printing resins(DT, CH, and CP) showed a higher value at 30 minute curing time than at 10 minute curing time.

• 마이크로전자및패키징학회지
• /
• 제18권1호
• /
• pp.15-21
• /
• 2011

전자기기의 고집적화를 위해 실리콘 웨이퍼의 두께가 점점 얇아지고 있으며 이로 인해 제조공정 중 균열이나 파손이 발생할 가능성이 높아지고 있다. 본 연구에서는 300 ${\mu}m$~100 ${\mu}m$ 두께의 반도체용 단결정 실리콘 웨이퍼의 파단 강도 및 파괴특성을 평가하였다. 기계적 연마를 통해 두께 (300, 200, 180, 160, 150, 100 ${\mu}m$)가 다른 실리콘 웨이퍼를 준비하였다. 하나의 웨이퍼에서 40개의 실리콘 다이(크기 : 62.5 mm${\times}$4 mm)를 얻어 4점 굽힘시험을 통해 평균 강도값을 구하였다. 강도분포의 통계적 해석을 위해 와이블 선도를 이용하여 형상인자(와이블 계수)와 크기인자(확률적 파괴강도)를 얻었다. 취성 실리콘 다이의 시편 크기(두께)효과와 파단 확률이 고려된 통계적 파단강도 값을 실리콘 다이 두께의 함수로 얻었다. 관찰된 파괴양상을 측정된 파단강도와 관련하여 고찰하였다.

• 대한치과기공학회지
• /
• 제33권4호
• /
• pp.283-289
• /
• 2011

Purpose: The purpose of this study was to evaluate flexural strength of full zirconia crown using block after clinical work. Methods: The three point bending test was used to measure the flexural strength of zirconia block. Statistical analysis was done using the Statistical Package for Social Sciences version 19.0 for Windows. As for the analysis methods, the study used analysis of variance, Tukey's test. Results: The ave Rage value of flexural strengths of WIELAND, Zirkonzahn, Hass, D-MAX were 516.2 MPa, 612.6MPa, 566.2MPa, 744.6MPa. The ave Rage value of Surface Roughness of WIELAND, Zirkonzahn, Hass, D-MAX were 0.39Ra, 0.33Ra, 0.33Ra, 0.47Ra. Conclusion: Flexural strength of zirconia block decreased after clinical work. Flexural strength of zirconia block is equal to or higher than flexural strength of dental metal, so zirconia block can be used as dental material.

• The Journal of Advanced Prosthodontics
• /
• 제4권1호
• /
• pp.1-6
• /
• 2012

PURPOSE. The aim of this study was to compare the flexural strength of polymethyl methacrylate (PMMA) and bis-acryl composite resin reinforced with polyethylene and glass fibers. MATERIALS AND METHODS. Three groups of rectangular test specimens (n = 15) of each of the two resin/fiber reinforcement were prepared for flexural strength test and unreinforced group served as the control. Specimens were loaded in a universal testing machine until fracture. The mean flexural strengths (MPa) was compared by one way ANOVA test, followed by Scheffe analysis, using a significance level of 0.05. Flexural strength between fiber-reinforced resin groups were compared by independent samples t-test. RESULTS. For control groups, the flexural strength for PMMA (215.53 MPa) was significantly lower than for bis-acryl composite resin (240.09 MPa). Glass fiber reinforcement produced significantly higher flexural strength for both PMMA (267.01 MPa) and bis-acryl composite resin (305.65 MPa), but the polyethylene fibers showed no significant difference (PMMA resin-218.55 MPa and bis-acryl composite resin-241.66 MPa). Among the reinforced groups, silane impregnated glass fibers showed highest flexural strength for bis-acryl composite resin (305.65 MPa). CONCLUSION. Of two fiber reinforcement methods evaluated, glass fiber reinforcement for the PMMA resin and bis-acryl composite resin materials produced highest flexural strength. Clinical implications. On the basis of this in-vitro study, the use of glass and polyethylene fibers may be an effective way to reinforce provisional restorative resins. When esthetics and space are of concern, glass fiber seems to be the most appropriate method for reinforcing provisional restorative resins.

• The Journal of Advanced Prosthodontics
• /
• 제11권4호
• /
• pp.202-208
• /
• 2019

PURPOSE. Fabrication of zirconia restorations with ideal mechanical properties in a short period is a great challenge for clinicians. The purpose of the study was to investigate the effect of heating rate on the mechanical and microstructural properties of monolithic zirconia. MATERIALS AND METHODS. Forty monolithic zirconia specimens were prepared from presintered monolithic zirconia blanks. All specimens were then assigned to 4 groups according to heating rate as Control, Group $15^{\circ}C$, Group $20^{\circ}C$, and Group $40^{\circ}C$. All groups were sintered according to heating rates with the sintering temperature of $1500^{\circ}C$, a holding time of 90 minutes and natural cooling. The phase composition was examined by XRD analysis, three-point bending test was conducted to examine the flexural strength, and Weibull analysis was conducted to determine weibull modulus and characteristic strength. Average grain sizes were determined by SEM analysis. One-way ANOVA test was performed at a significance level of 0.05. RESULTS. Only tetragonal phase characteristic peaks were determined on the surface of analyzed specimens. Differences among the average grain sizes of the groups were not statistically significant. The results of the three-point bending test revealed no significant differences among the flexural strength of the groups (P>.05). Weibull modulus of groups was ranging from 3.50 to 4.74. The highest and the lowest characteristic strength values were obtained in Group $20^{\circ}C$ and Control Group, respectively. CONCLUSION. Heating rate has no significant effect on the flexural strength of monolithic zirconia. Monolithic zirconia restorations can be produced in shorter sintering periods without affecting the flexural strength by modifying the heating rate.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2006년도 춘계 학술발표회 논문집(II)
• /
• pp.57-60
• /
• 2006

The purpose of this study is to assess performance of prepacked DFRCC material compared with the DFRCC material which is made by using general mixing method. From 4r-point bending test, bond strength test and chlorine ion penetration test, flexural stress, -deflection relations, bond strengths, and durability assessment have been obtained. From the experiments, premixed DFRCC shows relatively good performance.

• 한국구조물진단유지관리공학회 논문집
• /
• 제24권2호
• /
• pp.111-118
• /
• 2020

이 논문에서는 섬유의 혼입량에 따른 휨부재의 장기거동에 대한 영향을 평가하기 위하여 후크형 강섬유로 보강된 고강도 콘크리트의 휨 크리프 거동에 대한 평가가 이루어졌다. 실험은 150 × 150 × 600mm 크기를 갖는 섬유 혼입량(0, 0.75 및 1.5%)을 변수로 하는 6개의 휨 시험체를 대상으로 하였다. 노치를 갖는 휨 시험체에 휨 크리프 하중을 도입하기 위하여 4점 가력 휨 시험장치가 활용되었다. 휨강도의 40%인 크리프 재하하중은 레버 장치를 활용하여 도입되었고 90일 동안 도입된 하중은 로드셀에 의해 제어되었다. 크리프 하중의 도입시, 시험체 중앙부에 설치된 노치의 균열개구변위(CMOD)가 측정되었다. 크리프 시험후 각 시험체 대한 휨시험을 실시하여 각 시험체의 잔여강도를 평가하였다. 이상과 같은 실험결과로부터 섬유 혼입량은 고강도 콘크리트의 휨 크리프 거동에 주요한 영향을 끼치고 휨강도의 40% 범위내의 지속하중은 섬유보강된 고강도 콘크리트의 잔여강도에 부정적인 영향을 끼치지 않았다.

• 한국지반공학회논문집
• /
• 제28권10호
• /
• pp.17-25
• /
• 2012

NATM공법을 적용한 터널에서 숏크리트, 락볼트, 강지보재 등은 터널 굴착 후에 지반을 지지하기 위해 설치되는 주요한 지보재이다. 이전에는 H형강 지보재와 같은 강지보재가 많이 사용되었지만, 시공성이 떨어지는 등의 문제가 있어 격자지보재의 사용이 증가하였다. 본 연구에서는 기존의 격자지보재에서 스파이더와 강봉간의 접촉면적을 넓혀 강도가 증진된 신형 격자지보재를 개발하여 그 효과 및 성능을 검증하고자 LG-$50{\times}20{\times}30$, LG-$70{\times}20{\times}30$, LG-$95{\times}22{\times}32$ 세 가지 규격으로 3점 휨강도 실험과 4점 휨강도 실험을 실시하였다. 그 결과 기존의 격자지보재와 비교하여 신형의 격자지보재는 스파이더와 주강봉 접촉부에서는 평균 17.95%의 강도증진 효과가 있었고, 스파이더와 스파이더 사이에서는 평균 19.37%의 강도증진 효과가 있었으며 이는 스파이더와 주강봉 사이의 기계적 결합과 접촉면적 증가에 의한 격자지보재의 강성증가에 따른 결과로 사료된다.

• 대한치과기공학회지
• /
• 제30권1호
• /
• pp.65-71
• /
• 2008

The use of titanium in the field of dentistry has increased, due to their excellent biocompatibility, appropriate mechanical properties, corrosion-resistance and low price. However, many difficulties with the use of titanium for metal-ceramic crowns remain to be solved. The objective of this study was to evaluate the influence of surface modifications on the bonding characteristics of specific titanium porcelain bonded to cast titanium. The surfaces of Titanium were prepared with 4 test groups, i) sandblasted with particles of different size, ii) sandblasted after treated oxidization and oxidized after sandblast. We observed the bond strength and node aspect of titanium and ceramic, and respect to the methods of modifying surface of titanium by the test of mean roughness of surface, Scanning Electron Microscope, and 3-point flexural bend test. The results show that, 1. The specimens, which treated oxidization after process of sandblast with particles of 50um size, were the better for the bond strength in comparison with other specimen. 2. The specimen with process of sandblasting after oxidization treatment were the better for stability of the bond strength. 3. The wettability of titanium surface affect the bond strength.

• 콘크리트학회지
• /
• 제11권1호
• /
• pp.221-230
• /
• 1999

본 연구는 Belite를 사용한 고강도 철근콘크리트 보의 휨 거동에 관한 연구이다. 이를 위하여 Belite 시험체의 (1) 하중-처짐 관계와 시험체 중앙단면의 변형률 분호, (2) 하중-중립축관계와 모멘트-곡률 관계, (3) 연성평가, (4) 기존규준식과 실험값에 의한 휨강도 비교 등을 통하여 1종 보통 포트랜드 시멘트를 사용한 기준시험체(OPC)의 실험결과와 비교분석 하였다. 주요 실험변수는 콘크리트의 강도(350, 600kgf/$cm^2$)와 철근비(2D-13, 2D-16, 2D-19, 2D-22 and 2D-25)로 하였으며, 3점 재하를 실시하였다. 실험결과, 고강도${\cdot}$고유동 Belite 콘크리트를 사용한 본 실험의 경우, 전반적으로 1종 콘크리트의 휨거동 특성과 비슷한 경향을 보였다.