• 대한영상의학회지
• /
• 제81권2호
• /
• pp.310-323
• /
• 2020

선천성 심장질환의 치료에 있어서 그 해부학적인 구조를 올바르게 이해하는 것은 아주 중요하다. 이러한 선천성 심장질환의 구조적인 특징을 이해하는데 있어서 삼차원 프린팅 모델을 이용하는 것은 아주 효과적이다. 기존에 얻어진 전산화단층촬영이나 자기공명영상 혹은 심장 초음파 검사의 자료만으로는 정확한 복잡심장기형의 특징을 이해하는 것이 어려운 경우가 있으며, 삼차원 프린팅 모델의 사용이 이러한 제한점 들을 극복하는데 도움을 줄 수 있다. 최근 들어서는 삼차원 프린팅 모델을 이용해 선천성 심장질환의 교육과 수술 전 시뮬레이션 그리고 치료의 방침을 결정하는데 많은 도움을 받고 있으며, 실제 구체적인 환아들의 예를 통해서 이를 살펴보고자 한다. 또한 향후 그 기술의 발전 방향에 대해 알아보고, 심장외과 의사의 관점에서 수술 수기의 발전이나 훈련 등 여러 방면의 이용에 대해서도 살펴보고자 한다.

• Design & Manufacturing
• /
• 제14권1호
• /
• pp.1-7
• /
• 2020

In this study, the variation of the shrinkage in the thickness direction of the molded parts according to the gate size of the polymer core fabricated through the 3D printer using the SLS method was studied. The polymer cores are laser sintered and the powder material is nylon base PA2200. The polymer cores have lower heat transfer rate and rigidity than the metal core due to the characteristics of the material. Therefore, the injection molding test conditions are set to minimize the deformation of the core during the injection process. The resin used in the injection molding test is a PP material. The packing condition was set to 80, 90 and 100% of the maximum injection pressure for each gate size. The runner diameter used was ∅3mm, and the gates were fabricated in semicircle shapes with cross sections 1, 2, and 3 ㎟, respectively. Thickness measurement was performed for 10 points at 2.5 mm intervals from the point 2.5 mm away from the gate, and the shrinkage to thickness was measured for each point. The shrinkage rate according to the gate size tends to decrease as the cross-sectional area decreases as the maximum injection pressure increases. The average thickness shrinkage rate was close to 0% when the packing pressure was 90% for the gate area of 1mm2. When the holding pressure was set to 100%, the shrinkage was found to decrease by 3% from the standard dimension due to the over-packing phenomenon. Therefore, the smaller the gate, the more closely the molded dimensions can be molded due to the high pressure generation. It was confirmed that precise packing process control is necessary because over-packing phenomenon may occur.

• 터널과지하공간
• /
• 제26권6호
• /
• pp.516-523
• /
• 2016

절리면의 거칠기는 암반의 역학적, 수리적 거동에 중요한 영향을 미치는 요인이다. 따라서 이를 해석하기 위한 여러 가지 구성 모델 및 거칠기 정량화 연구가 실험적, 경험적으로 수행되어 왔다. 최근 3D 프린팅 기술의 발전은 특정 거칠기를 갖는 절리면을 생성하는 데 활용될 수 있으며 본 논문에서는 이에 적합한 절리면 생성기법을 소개하고 정량적 평가를 수행하였다. 프랙탈 이론에 따른 랜덤중점변위법을 적용하였으며 생성된 절리면의 거칠기 평가는 $Z_2$의 분포를 계산하여 수행하였다. 그 결과 입력변수 제어를 통하여 목표로 한 거칠기를 구현할 수 있었으며 더 나아가 특정 거칠기 이방성비를 갖는 절리면을 생성할 수 있음을 확인하였다.

• The Journal of Advanced Prosthodontics
• /
• 제8권3호
• /
• pp.219-223
• /
• 2016

PURPOSE. This study aimed to create a digitized database of fabricated obturators to be kept for patients' potential emergency needs. MATERIALS AND METHODS. A chairside intraoral scanner was used to scan the surfaces of an acrylic resin obturator. The scanned data was recorded and saved as a single standard tessellation language file using a three-dimensional modeling software. A simulated obturator model was manufactured using fused deposition modeling technique in a three-dimensional printer. RESULTS. The entire obturator was successfully scanned regardless of its structural complexity, modeled as three-dimensional data, and stored in the digital system of our clinic at a relatively small size (19.6 MB). A simulated obturator model was then accurately manufactured from these data. CONCLUSION. This study provides a proof-of-concept for the use of digital technology to create a digitized database of obturators for edentulous maxillectomy patients.

• Tribology and Lubricants
• /
• 제36권3호
• /
• pp.147-152
• /
• 2020

This paper is within the framework of an adhered complete contact problem wherein the contact between a half plane and sharp edged indenter, both of which are elastic in character, is constituted. The eigensolutions of the contact shear and normal stresses, σ_rq and σ_q, respectively, are evaluated via asymptotic analysis. The ratio of σ_rq/σ_qq is investigated and compared with the coefficient of friction, μ, of the contact surface to observe the propensity to slip on the contact surface. Interestingly, there exists a region of |σ_rθ/σ_θθ| ≥ |μ|. Thus, slipping can occur, although the problem is solved under the condition of an adhered contact without slipping. Given that a tribological failure potentially occurs at the slipping region, it is important to determine the size of the slipping region. This aspect is also factored in the paper. A simple example of the adhered contact between two elastically dissimilar squares is considered. Finite element analysis is used to evaluate generalized stress intensity factors. Furthermore, it is repeatedly observed that slipping occurs on the contact surface although the size of it is extremely small compared with that of the contacting squares. Therefore, as a contribution to the field of contact mechanics, this problem must be further explained logically.

• 한국해양공학회지
• /
• 제3권2호
• /
• pp.617-617
• /
• 1989

This paper deals with a fatigue life prediction of a surface crack based on the experimentally obtained relationship between surface crack length ratio $a/a_{f}$ and cycle ratio $N/N_{f}$ using micro computer. Firstly $a/a_{f}$-$N/N_{f}$ curves obtained from experimental tests, were assumed as three curves UC(the upper limit curve), LC(the lower limit curve) and MC(the middle curve), and these were utilized to predict the fatigue life. Comparing the calculated values which represent the characteristics of crack growth behaviors from the three assumed curves with the experimental ones, it has been found that in the stable crack growth region, they coincide reasonably well each other. And the differences between the fatigue lives obtained from the assumed curves and the experimental fatigue life did not exceed 20%. Using the characteristics of $a/a_{f}$-$N/N_{f}$ curves, it is possible to predict the da/dN-Kmax curves and the S-$N_{f}$ curves.

• 공학교육연구
• /
• 제23권4호
• /
• pp.14-21
• /
• 2020

The aim of this study was to establish an university informal program roadmap, and also to draw up operational plans for human resources with core technologies of the fourth industry. To do this, first we derived university informal education program draft through experts workshop, then conducted a survey regarding the female university students' perception of educational programs and their educational needs on the 4th core technology matching programs. The following main results were obtained : First, students preferred 'hands-on training' by professionals and they wanted to be trained during summer or winter holidays or the night time during semesters. Also, they thought two hours of training per session was appropriate. Regarding these results, there was no difference depending on the majors. Second, while students had highly preferred for the courses related to data analysis, Arduino programing and VR(virtual reality), those related to 3D printing modeling were less preferred. Depending on the majors, preferred courses had different priorities, but non-preferred courses were similar regardless of majors. Based on these results, the university informal curriculum model and the operation plans for the core technologies of the fourth industry were proposed.

• 한국인터넷방송통신학회논문지
• /
• 제19권5호
• /
• pp.245-250
• /
• 2019

현대 주조산업에서는 적층제조기술과 같은 신기술을 도입하면서 과거에는 불가능했던 일들의 실현가능성을 보여주고 있다. 이미 해외에서는 적층제조기술을 활용한 중자 생산 및 적용 사례가 심심치 않게 보도되고 있으며, 정부지원 하에 고유 기술들을 개발하고 시장을 확장해 나가고 있다. 반면 국내에서는 고유장비 기술은커녕 적층제조기술의 활용조차 전무한 실정이다. 이러한 상황에서 적층제조기술의 도입과 국산화는 반드시 필요하다. 본 논문의 각 장에서는 여러가지 적층제조기술 중 접착제 분사 기술에 관련된 적층제조장비의 개발 과정에서부터 개발 장비를 활용한 산업용 중자 생산의 내용을 다루고 있으며, 실제 주조 산업의 적용 가능성에 대해서 언급하고 있다.

• 대한치과기공학회지
• /
• 제42권2호
• /
• pp.113-120
• /
• 2020

Purpose: This study is to compare and analyze the shrinkage of the specimen after UV irradiation of UV cured resin at 5, 15, and 30 minutes. Methods: A cylindrical UV cured specimen was produced using a stainless steel mold. UV cured resin specimens were prepared in three groups: 5 minutes cured (5M), 15 minutes cured (15M), and 30 minutes cured (30M). The measurement was made in total 3rd. The measurement was made in total 3rd. The primary measurement was made after 24 hours using a digital measuring instrument. The 2nd and 3rd measurements were deposited in a constant temperature water bath and the shrinkage was measured. The measured data was calculated by referring to the ASTM C326 linear measurement calculation method. T-test and One-way ANOVA were performed to test the significance between groups. The post-test was conducted with Tukey (α=0.05). Results: When the inner diameter and the outer diameter of the three groups not placed in the water bath were compared and analyzed, the contraction was the smallest at 6.8% in the 5M group, and the contraction was the largest at 7.3% in the 30M group. In the outer diameter, the contraction of the 5M group was the smallest at 3.5%, and the contraction of the 30M group was the largest at 4.5%. Shrinkage decreased in all three groups immersed in a water bath for 3-7 days. Conclusion: In the UV cured resin specimen, the shrinkage increased as the amount of UV irradiation increased.

• 박물관보존과학
• /
• 제29권
• /
• pp.99-110
• /
• 2023

석조문화유산으로부터 결손된 석재편은 비교적 무겁고 부피가 커 직접 맞춰보고 원위치를 찾는 데 한계가 있으며, 수작업 시 이차적 물리적 손상이 발생할 가능성이 있다. 따라서 이 연구에서는 72점의 석재편이 함께 발굴된 예산 화전리 석조사면불상을 대상으로 디지털 복원을 통해 결손부와 석재편의 형상학적 관련성을 파악하고, 전시활용을 위해 3차원 프린팅 복제모형을 제작하였다. 디지털 복원을 위해 가상 공간에서 3차원 스캐닝 모델의 좌표를 정렬한 후 형상 유사도가 존재하는 석재편을 선정하였다. 또한 이 석재편을 3차원 프린터로 출력하여 결손부와 물리적인 접합 여부를 확인하였고, 이렇게 하여 총 7개소 9점의 석재편의 원위치를 파악하였다. 이러한 연구성과를 전시에 활용하기 위해 3차원 프린팅으로 석조사면불상의 1:1 복제모형을 제작하였고, 원위치가 파악된 석재편들 역시 복원되었다. 이번 연구에 사용된 디지털 기술은 직접적 수작업 방식의 한계를 보완하였을 뿐 아니라 유사 문화유산의 기록화, 복원, 복제 분야에 확대적용 가능성을 제안했다는 데 큰 의의가 있는 것으로 판단된다.