• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.286-288
• /
• 2007

In this paper, the fast locking PLL Frequency Synthesizer with low phase noise in a 0.18um CMOS process is presented. Its main application IS for the 915MHz ISM band wireless transponder upon the CPFSK (Continuous Phase Frequency Shift Keying) modulation scheme. Frequency synthesizer, which in this paper, is designed based on self-biased techniques and is independent with processing technology when damping factor and bandwidth fixed to most important parameters as operating frequency ratio, broad frequency range, and input phase offset cancellation. The proposed frequecy synthesizer, which is fully-integrated and is in 320M $^{\sim}$ 960MHz of the frequency range with 10MHz of frequency resolution. And its is implemented based on integer-N architecture. Its power consumption is 50mW at 1.8V of supply voltage and core area is $540{\mu}m$ ${\times}$ $450{\mu}m$. The measured phase noises are -117.92dBc/Hz at 10MHz offset, with low settling time less than $3.3{\mu}s$.

• Journal of the Optical Society of Korea
• /
• 제13권4호
• /
• pp.434-438
• /
• 2009

In this paper, a 12.5-Gb/s optical transmitter is implemented using 0.13-${\mu}m$ CMOS technology. The optical transmitter that we constructed compensates temperature effects of VCSEL (Vertical cavity surface emitting laser) using auto-power control (APC) and auto-modulation control (AMC). An external monitoring photodiode (MPD) detects optical power and modulation. The proposed APC and AMC demonstrate 5$\sim$20-mA of bias-current control and 5$\sim$20-mA of modulation-current control, respectively. To enhance the bandwidth of the optical transmitter, an active feedback amplifier with negative capacitance compensation is exploited. The whole chip consumes only 140.4-mW of DC power at a single 1.8-V supply under the maximum modulation and bias currents, and occupies the area of 1280-${\mu}m$ by 330-${\mu}m$ excluding bonding pads.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2004년도 ICEIC The International Conference on Electronics Informations and Communications
• /
• pp.199-203
• /
• 2004

In this paper, we only describe the digital block of two-channel 18-bit analog-to-digital (A/D) converter employing sigma-delta method and xl28 decimation. The device contains two fourth comb filters with 1-bit input from sigma­delta modulator. each followed by a digital half band FIR(Finite Impulse Response) filters. The external analog sigma-delta modulators are sampled at 6.144MHz and the digital words are output at 48kHz. The fourth-order comb filter has designed 3 types of ways for optimal power consumption and signal-to-noise ratio. The following 3 digital filters are designed with 12tap, 22tap and 116tap to meet the specification. These filters eliminate images of the base band audio signal that exist at multiples of the input sample rate. We also designed these filters with 8bit and 16bit filter coefficient to analysis signal-to-noise ratio and hardware complexity. It also included digital output interface block for I2S serial data protocol, test circuit and internal input vector generator. It is fabricated with 0.35um HYNIX standard CMOS cell library with 3.3V supply voltage and the chip size is 2000um by 2000um. The function and the performance have been verified using Verilog XL logic simulator and Matlab tool.

• 전자공학회논문지A
• /
• 제33A권4호
• /
• pp.152-161
• /
• 1996

In tis work, a three-stage pipelined A/D converter (ADC) was implemented to obtain 10-bit resolution at a conversion rate of 20 msamples/s for video applications. The ADC consists of three identical stages employing a mid-rise coding technique. The interstage errors such as offsets and clock feedthrough are digitally corrected in digitral logic by one overlapped bit between stages. The proposed ADC is optimized by adopting a unit-capacitor array architecture in the MDAC to improve the differential nonlinearity and the yield. Reduced power dissipation has been achieve dby using low-power latched comparators. The prototype was fabricated in a 0.8$\mu$m p-well CMOS technology. The ADC dissipates 160 mW at a 20 MHz clock rate with a 5 V single supply voltage and occupies a die area of 7 mm$^{2}$(2.7 mm $\times$ 2.6mm) including bonding pads and stand-alone internal bias circuit. The typical differential and integral nonlinarities of the prototype are less than $\pm$ 0.6 LSB and $\pm$ 1 LSB, respectively.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.505-506
• /
• 2006

In this paper, the linearization technique for CMOS low-noise amplifier (LNA) using the derivative superposition method through the multiple gated transistors configuration is presented. LNA based on 0.13um RF CMOS process has been implemented with a modified cascode configuration using multiple gated common source transistors to fulfill a high linearity. Compared with a conventional cascode type LNA, the third order input intercept point (IIP3) per DC power consumption (IIP3/DC) is improved by 3.85 dB. The LNA achieved 2.5-dBm IIP3 with 13.4-dB gain, 3.6 dB NF at 2.4 GHz consuming 8.56 mA from a 1.5-V supply.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.195-196
• /
• 2007

Since the digital TV signal band is very wide ($54{\sim}806MHz$), the VCO used in the frequency synthesizer must also have a wide frequency tuning range. Multiple LC VCOs have been used to cover such wide frequency band. However, the chip area increases due to the increased number of integrated inductors. In this paper, a scheme is proposed to cover the full band using only one VCO. The RF VCO block designed using a 0.18um CMOS process consists of a wideband LC VCO, five divide-by-2 circuits and several buffers. The simulation results show that the designed circuit has a phase noise at 10kHz better than -87dBc/Hz throughout the signal band and consumes 10mA from a 1.8V supply.

• 전자공학회논문지
• /
• 제51권10호
• /
• pp.57-63
• /
• 2014

본 논문은 전력소모와 면적을 줄인 지연된 피드-포워드 경로를 갖는 3차 SDM 구조를 제안하였다. 제안한 SDM은 기존의 적분기 2개로 구현된 3차 SDM(Sigma-Delta Modulator) 구조를 개선하였다. 제안된 구조에서는 기존 구조의 둘째 단에 지연된 피드-포워드 경로를 삽입함으로써 첫째 단의 계수 값을 2배로 증가시킬 수 있어 기존구조에 비하여 첫째 단 적분기 커패시터($C_I$)를 1/2로 감소시킬 수 있다. 그러므로 첫째 단 적분기의 부하 커패시턴스가 1/2로 작아지기 때문에 첫째 단 연산증폭기의 출력전류는 51%, 첫째 단의 커패시터 면적은 48% 감소되어 제안한 구조는 전력과 면적을 최적화 할 수 있다. 본 논문에서 제안한 구조를 이용하여 설계된 3차 SC SDM은 $0.18{\mu}m$ CMOS 공정에서 공급전압 1.8V, 입력신호 1Vpp/1KHz, 신호대역폭 24KHz, 샘플링 주파수 2.8224MHz 조건으로 시뮬레이션 하였다. 그 결과 SNR(Signal to Noise Ratio) 88.9dB, ENOB(Effective Number of Bits) 14비트이고 SDM의 전체 전력소모는 $180{\mu}W$이다.

• 전자공학회논문지SC
• /
• 제46권2호
• /
• pp.72-77
• /
• 2009

본 논문은 별도 기준 클록 없이 고속 시리얼 데이터 통신을 위한 3.2Gb/s 클록 데이터 복원(CDR) 회로를 설명한다. CDR회로는 전체적으로 5부분으로 구성되며, 위상검출기(PD)와 주파수 검출기(FD), 다중 위상 전압 제어 발진기(VCO), 전하펌프(CP), 외부 루프필터(LF)로 구성되어 있다. CDR회로는 half-rate bang-bang 타입의 위상 검출기와 입력 pull-in 범위를 늘릴 수 있도록 half-rate 주파수 검출기를 적용하였다. VCO는 4단의 차동 지연단(delay cell)으로 구성되어 있으며 튜닝 범위와 선형성 향상을 위해 rail-to-rail 전류 바이어스단을 적용하였다 각 지연단은 풀 스윙과 듀티의 부정합을 보상할 수 있는 출력 버퍼를 갖고 있다. 구현한 CDR회로는 별도의 기준 클록 없이 넓은 pull-in 범위를 확보할 수 있으며 기준 클록 생성을 위한 부가적인 Phase-Locked Loop를 필요치 않기 때문에 칩의 면적과 전력소비를 효과적으로 줄일 수 있다. 본 CDR 회로는 0.18um 1P6M CMOS 공정을 이용하여 제작하였고 루프 필터를 제외한 전체 칩 면적은 $1{\times}1mm^2$이다. 3.2Gb/s 입력 데이터 율에서 모의실험을 통한 복원된 클록의 pk-pk 지터는 26ps이며 1.8V 전원전압에서 전체 전력소모는 63mW로 나타났다. 동일한 입력 데이터 율에서 테스트를 통한 pk-pk 지터 결과는 55ps였으며 신뢰할 수 있는 입력 데이터율 범위는 약 2.4Gb/s에서 3.4Gb/s로 나타났다.

• 대한전자공학회논문지SD
• /
• 제45권2호
• /
• pp.118-124
• /
• 2008

디지털 비디오 방송표준(DVB-S2)은 순방향 에러 코딩방법으로 BCH와 LDPC을 연결한 시스템을 내부코딩으로 사용한다. DVB-S2에서 LDPC 코드는 11개의 서로 다른 부호화 율을 정의하고 있기 때문에, DVB-S2 LDPC 복호기는 다양한 부호화 율을 지원해야 한다. 11개의 부호화 율 중에서 7가지(3/5, 2/3, 3/4, 4/5, 5/6, 8/9, 9/10)는 균일한 부호화 율이고, 나머지 4가지(1/4, 1/3, 2/5, 1/2)는 비균일 부호화 율이다. 본 논문에서는 균일한 LDPC 코드를 위한 유연한 복호기를 제시한다. 제안된 복호기는 칩의 면적, 메모리의 효율, 처리속도 등에서 많은 장점을 갖는 반 병렬 복호 구조와 변수노드와 체크노드의 내부 연결선을 줄이고 다양한 부호화 율을 지원할 수 있도록 Benes 네트워크를 결합하여 블록크기가 64,800까지 사용가능하도록 설계하였다. 제안하는 복호기는 200MHz에서 193.2MbPs의 처리속도를 갖으며, 면적은 $16.261m^2$이고, 전력은 공급전압이 1.5V에서 198mW의 소모를 보인다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제8권2호
• /
• pp.195-200
• /
• 1995

The design of this field experiment was a completely randomized block arrangement, consisted of 16 treatments (Gliricidia sepium provenances) and 6 blocks as replications with 12 plants per provenance. Of the 16 gliricidia provenances, six were from Mexico (M), four were from Guatemala (G), and one each was from Colombia (C), Indonesia (I), Nicaragua (N), panama (P), Costa Rica (R), and Venezuela (V). After 12 months establishment the gliricidia were lopped regularly 4 times a year, twice during the 4 months wet season and twice during the 8 months dry season at 150 cm height. There was variation (p < 0.05) in stem elongation from 22 to 80 cm, leaf retained from 118 to 209%, branch number from 13 to 24, fodder yield from 1,015 to 1,671 g DW/plant and wood yield from 792 to 1,662 g DW/plant among the provenances; and such variations were affected by the seasons. Belen (N14), Retalhuleu (G14) and Bukit Bali (I) provenances were ranked first, second and third, respectively, measured in terms of leaf retention, stem elongation, fodder and wood yields during the wet and dry seasons.