• Journal of the Korean Geotechnical Society
• /
• v.26 no.7
• /
• pp.7-16
• /
• 2010

Stress history increases the residual horizontal stress of granular soil and, consequently, the penetration resistance. This study analyzes the effect of stress history on the cone resistance ($q_c$), horizontal stress index ($K_D$) and dilatometer modulus ($E_D$) of CPT and DMT from calibration chamber specimen in OC as well as NC state. Test results show that the normalized cone resistance by mean effective stress correlates well with the relative density and the state parameter, whereas the normalized cone resistance by vertical effective stress is a little affected by stress history. The influence of stress history is more reflected on $K_D$ than $E_D$ and $q_c$. The $K_D/K_0$, in which the effect of stress history on $K_D$ is compensated by the at-rest coefficient of earth pressure, $K_0$, is related to relative density, state parameter and the normalized cone resistance by mean effective stress. It is also observed that the normalized dilatometer modulus by mean effective stress ($E_D/{\sigma}_m'$) shows a unique correlation with the state parameter, regardless of stress history.

• Journal of the Korean Geotechnical Society
• /
• v.24 no.10
• /
• pp.147-160
• /
• 2008

This paper presents the results of full-scale loading tests performed on 54 passive anchors and 4 group anchored footings grouted to various lengths at several sites in Korea. The test results, the failure mechanisms as well as uplift capacities of rock anchors depend mostly on rock type and quality, embedded fixed length, properties of the discontinuities, and the strength of rebar. Anchors in poor quality rocks generally fail along the grout/rock interfaces when their depths are very shallow (a fixed length of less than 1 m). However, even in such poor rocks, we can induce a more favorable mode of rock pull-up failure by increasing the fixed length of the anchors. On the other hand, anchors in good quality rocks show rock pull-up failures with high uplift resistance even when they are embedded at a shallow depth. Laboratory test results revealed that a form of progressive failure usually occurs starting near the upper surface of the grout, and then progresses downward. The ultimate tendon-grout bond strength was measured from $18{\sim}25%$ of unconfined compressive strength of grout. One of the important findings from these tests is that the measured strains along the corrosion protection sheath were so small that practically the reduction of bond strength by the presence of sheath would be negligible. Based on test results, the main parameters governing the uplift capacity of the rock anchor system were determined. By evaluation of the ultimate uplift capacity of anchor foundations in a wide range of in situ rock masses, rock classification suitable for a transmission tower foundation was developed. Finally, a very simple and economical design procedure is proposed for rock anchor foundations subjected to uplift tensile loads.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2020.06a
• /
• pp.18-18
• /
• 2020

금강하구와 같이 막힌 대형 하구는 근본적으로 복잡한 물리화학적 프로세스와 다양한 이해당사자간의 갈등 때문에 단편적인 접근으로는 관리의 한계가 있을 수밖에 없는 환경이다. 더욱이 하굿둑의 갑문을 열어 하구순환을 복원하는 해수유통 사업은 그 자체가 가지는 환경적 효용성의 확인과 기존 용수이용 체계의 전면적 변화와 관련된 상당한 비용이 요구된다는 면에서 특별한 논란이 되어왔다. 본 연구는 해수유통으로 인한 금강 하구해역의 수리, 수질, 퇴적 및 생태 등 다양한 환경적 변화를 집중적인 현장 조사 및 통합 모델링을 통해 정량적으로 예측하고 이를 지역 이해당사자 논의 체계인 금강하구해역정책협의회에 제공함으로써 해수유통과 연관된 이해당사자 간 갈등을 완화하고 과학적 자료에 근거한 정책결정을 지원하기 위해 수행되었다(과학-정책의 통합). 조사연구는 하굿둑 갑문 개방에 따른 다양한 시나리오별로 해수유통으로 인한 영향을 하구해역(하굿둑의 바다 쪽 해역)과 하구호(하굿둑의 하천 쪽 담수역)에 미치는 영향을 검토하였다(하천-하구호-연안해역의 공간적 통합). 시나리오는 하구해역정책협의회의 요구사항을 반영하여 개발되었고, 시나리오별 영향파악은 수리(조석 및 파랑 포함), 퇴적물 이동 및 수질은 Delft3D모델을, 유역으로부터의 유량 및 오염물질 부하량은 분포형 비점모델인 STREAM을, 김양식과 이매패류 생산량을 추정하는 생태모델은 통계기반의 포인트 모델을 통해 이루어졌다(수리-퇴적-수질-생태계 모델의 통합). 시나리오 분석결과, 상시 해수유통을 제외한 대부분의 하굿둑 부분 개방 시나리오에서는 하구해역에 미치는 영향이 제한적으로 나타나는 것으로 예측되었다. 이는 하굿둑 부분 개방에 따른 담수방류량 및 이에 대응하는 해수의 유동패턴이 현재와 크게 달라지지 않음을 반영한다. 반면 하구호에 대한 영향은 하구해역에 비해 하굿둑 갑문 운영시나리오에 따라 상대적으로 민감하게 변화되는 것으로 예측되었다. 갑문의 부분 개방을 통해 하구호의 수위를 현재 대비 5cm~50cm 변화시켰을 때 1psu 염분의 저층에서의 침투거리는 하굿둑 상류 6km~18km 정도로 예측되었고 갑문 개방에 의해 염분 침투 거리의 조절이 가능할 것으로 나타났다. 단, 사용된 통합모델은 수년간의 검보정 과정을 반복적으로 수행하여 예측의 정확도를 지속적으로 개선하였지만, 모델운영 자체의 불확실성을 고려할 때 실제 해수유통을 위해서는 시범개방을 통해 모델 예측의 결과를 확인할 필요가 있다.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.25 no.2
• /
• pp.5-11
• /
• 2023

Rehmannia glutinosa is a perennial herb belonging to the family Scrophulariaceae and is used in traditional oriental medicine. This study was carried out current status of breeding of R. glutinosa, its problems, and the matters to be improved were made. Based on the research data published so far, this study summarized the characteristics of breeds cultivated in Korea and compared and analyzed the status of cultivation area, production, import, and price changes for 15 years from 2008 to 2021. The cultivated area of R. glutinosa is gradually decreasing, and the amount of import is increasing and decreasing repeatedly. Amount of import has declined significantly. There was a lot of disinfection and disposal in the middle of import, and dried Jihwang and Sukjihwang were imported without distinction. R. glutinosa must be cultivated and supplied as a variety desired by the industry, cultivation techniques need to be taught to producers. In order to clearly identify the amount of import, import code of dried Jihwang and Sukjihwang must be classify. In addition, it is necessary to develop and supply harvesting agricultural machines for mechanization. For the stable income of producers, supply control through contract cultivation will ensure stable farm income.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.3
• /
• pp.633-640
• /
• 2023

In this study, numerical analysis was performed based on field investigation to derive an appropriate reinforcement method by analyzing the displacement behavior characteristics of concrete blocks generated in the direct fixation track on the bridges of the serviced light rail transit. The track of this study was a direct fixation track on a sharp curved track, and the problem of movement of the concrete blocks installed on the bridge deck in the longitudinal and lateral directions occurred. In this study, based on the finite element model using 3D solid elements, the behavior of the direct fixation track that could be occurred under operating load conditions was analyzed. In addition, the reinforcement effect of various reinforcement methods was analyzed. As a result of analyzing the lateral displacement before and after reinforcement, it was analyzed that the maximum lateral displacement after reinforcement under the extreme lateral wheel loads significantly decreased to about 3% (about 0.1mm) compared to before reinforcement. In addition, as a result of examining the generated stress of the filling mortar, bridge decks, and reinforcing bar, it was analyzed that all of them secured a sufficient safety factor of 2.6 or higher, and the optimal conditions for the reinforcement method were derived. Therefore, it is judged that the number of anchoring reinforcements and symmetrical anchor placement reviewed in this study will be effective in controlling the occurrence of lateral displacement of concrete blocks and securing the structural integrity of bridges and concrete blocks.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.28 no.2C
• /
• pp.83-94
• /
• 2008

In this study an effective stress analysis was performed to evaluate liquefaction potential and ground settlement for reclaimed sites. The effective stress model can simulate the stiffness degradation due to excess pore pressure and resulting ground deformation. It is applicable to a wide range of strain. An equivalent linear analysis suitable for low strain levels was also carried out to compare the effective stress analysis. Shear stress ratio calculated from an equivalent linear analysis was used to determine SPT blow count to prevent liquefaction. Depending on the magnitude of potential earthquake and fine contents, the SPT blow count was converted into an equivalent cone tip resistance. It was compared with the measured cone tip resistance. The measured elastic shear wave velocity and cone tip resistance from two reclaimed sites in Incheon were used to perform liquefaction analyses. Two liquefaction evaluation methods showed similar liquefaction potential which was evaluated continuously. The predicted excess pore pressure ratio of upper 20 m was between 40% and 70%. The calculated post-shaking settlement caused by excess pore pressure dissipation was less than 10 cm.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.5A
• /
• pp.901-908
• /
• 2006

The structural integrity of containment building in Nuclear Power Plants has to be verified by the ISI(In Service Inspection) because there are some variations on the structural behavior of it due to the change of the physical properties of concrete and tendon with the lapse of time. In this study, the program 'SAPONC-CANDU' which can monitor and analyze the structural behavior of the containment building with grouted tendon (CANDU-type, 'Wolsong unit-2, 3, and 4' in Korea) was developed. This program is based on the algorithm which can calculate the prediction values of the quantities of strain variation for the vibrating-wire strain gauges embedded into the concrete of the containment building under temperature and time dependent factors which are creep, shrinkage, and prestressing force. The readings of the strain gauges are used as input data for the operation of the program. And it finally provides graphically a prediction value, line and band of the quantity of strain variation for the respective strain gauges, therefore, it is thought that the site engineers are able to assess the structural integrity of the domestic containment building with grouted tendon with easy using this program.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.3A
• /
• pp.555-563
• /
• 2006

Recently, many bridges become not only functionally obsolete of bridge deck due to inadequate width but also structurally deficient of substructure due to erosion. In these cases, widening is almost always more economical than complete replacement, and therefore there is a need to make available the results of research and field experience pertaining to the widening of bridge substructure. But, an experimental study for the guarantee of unification between existing and new substructure with adhesive anchor is so insufficient that the development of adhesive anchor system for the unification should be settled promptly. The purpose of the present study is to explore pull out and shear characteristics of adhesive anchor system. For this purpose, several series of concrete specimens have been tested. Major test variables were the bonded length, anchor diameter and anchor slope. The pull out strength, bond stress and shear strength of adhesive faces were measured for the specimens. The present study indicates that the pull out strength increased with more bonded length and more anchor diameter, and that the bond stress decreased with more bonded length and more anchor diameter. The pull out strength and the bond stress increases with more anchor slope and it is considered that the slope of $5^{\circ}$ was more efficient. From the shear tests, it is supposed that anchor diameters more than D19 was proper to the adhesive anchor. Finally, it is expected that both experimental data in these tests and further study including mock-up tests will contribute to the establishment of the unification between existing and new substructure with adhesive anchor.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.11 no.2
• /
• pp.151-162
• /
• 2009

This study proposes a new methodology for quantitative rock classification in unsampled rock zone, which occupies the most of tunnel design area. This methodology is to train an ANN (artificial neural network) by using results from a drilling investigation combined with electric resistivity survey in sampled zone, and then apply the trained ANN to making a prediction of grade of rock classification in unsampled zone. The prediction is made at the center point of a shifting window by using a number of electric resistivity values within the window as input reference information. The ANN training in this study was carried out by the RPROP (Resilient backpropagation) training algorithm and Early-Stopping method for achieving a generalized training. The proposed methodology is then applied to generate a rock grade distribution on a real tunnel site where drilling investigation and resistivity survey were undertaken. The result from the ANN based prediction is compared with one from a conventional kriging method. In the comparison, the proposed ANN method shows a better agreement with the electric resistivity distribution obtained by field survey. And it is also seen that the proposed method produces a more realistic and more understandable rock grade distribution.

• Korean Journal of Plant Taxonomy
• /
• v.53 no.2
• /
• pp.126-147
• /
• 2023

The taxonomic identity of Elaeagnus ×maritima and E. ×submacrophylla (Elaeagnaceae) in Korea is unclear, yet they are presumed to be hybrid taxa based on their morphology. To determine their hybrid origins, a morphological analysis (field surveys and specimen examinations) and a molecular analysis involving two nuclear ribosomal DNA (nrDNA) regions (internal transcribed spacer and 5S non-transcribed spacer) and one chloroplast DNA (cpDNA) region (matK) were conducted. The morphological analysis revealed that E. ×maritima showed certain morphological similarities to E. glabra, whereas E. ×submacrophylla showed certain morphological similarities to E. pungens. However, the molecular analysis indicated that E. ×maritima exhibited additive species-specific sites of E. glabra and E. macrophylla in the nrDNA regions. Notably, E. ×submacrophylla showed various aspects, with some individuals exhibiting additive species-specific sites of E. pungens and E. macrophylla in the nrDNA and E. macrophylla sequences in the cpDNA regions, some individuals exhibiting E. macrophylla sequences in the nrDNA and E. pungens sequences in the cpDNA regions, and some individuals displaying E. macrophylla sequences in both the nrDNA and cpDNA regions, despite an intermediate morphology between E. pungens and E. macrophylla. These results indicate that these two species are of hybrid origin and frequently cross between parental and hybrid individuals.