• 한국전기전자재료학회논문지
• /
• 제14권2호
• /
• pp.163-168
• /
• 2001

This dissertation describes the development of a sensor for measuring microscopic displacement where we use CoFeSiB amorphous alloy magnetic ribbon having near zero magnetostrictive properties. For the development of the sensor, we first fabricate amorphous alloy magnetic ribbon, and then investigate its physical and magnetic properties. Finally, its possibility of practical application as a displacement sensor is discussed. The experimental samples were made of near zero magnetostrictive (Co$\_$0.94/Fe$\_$0.06/)$\_$9/Si$_2$B$\_$19/ alloy which were fabricated by a rapid liquid quenching method. As a results, we got amorphous alloy magnetic ribbons of 12㎛ in thickness, 10 mm in length, and 2.5 m in width. It was found that the crystallization temperature and the Curie temperature are around 451$\^{C}$ and around 441$\^{C}$ respectively. We couldn't observe any noticeable change of the impedance frequency of 10MHz, but observed the impedance change of 3.76 %/Oe at 100 MHz. The inductance was nearly stable over the frequency range of 1∼10 MHz, In addition, it was observed that the variation of the inductance and the impedance were linear within the displacement ranges of 20∼60㎛. As the results of the experiments, it is suggested that the displacement sensor which is fabricated by using amorphous alloy magnetic ribbon of (Co$\_$0.04/Fe$\_$0.06/)$\_$79/Si$_2$B$\_$19/ compound, can be used as a sensor to detect microscopic displacement.

• 한국주조공학회지
• /
• 제15권3호
• /
• pp.252-261
• /
• 1995

The purposes of this study were to investigate the microstructural changes in alloy ribbons of Al-Fe-Mo-Si quarternary system at $450{\sim}500^{\circ}C$, and to study the coarsening mechanism of fine precipitates. Using the hot stage in TEM, in situ microstructural changes in Al-4Fe-0.5Mo-1.5Si alloy ribbon and Al-8Fe-2Mo-1.5Si alloy ribbon have been examined successively up to 60 hours at $450^{\circ}C$ and $500^{\circ}C$. Cell structure in zone B of Al-4Fe-0.5Mo-1.5Si alloy ribbon was observed to collapse even in 10 minutes by in-situ heating at $450^{\circ}C$ and the size of precipitates in zone B increased twice in 60 hours. The precipitates in zone A of Al-4Fe-0.5Mo-1.5Si alloy ribbon showed slower coarsening rate than those in zone B by in-situ heating at $450^{\circ}C$. The precipitates in zone A of Al-8Fe-2Mo-1.5Si alloy ribbon increased 50% by in-situ heating at $500^{\circ}C$ in 50 hours compared to the initial precipitates while any microstructual change in zone B was not observed by in-situ heating at $500^{\circ}C$ up to 50 hours. Only the precipitates in zone A of Al-4Fe-0.5Mo-1.5Si alloy ribbon satisfied $r^3{\propto}t$ relationship of coarsening mechanism.

• 한국자기학회지
• /
• 제3권3호
• /
• pp.201-207
• /
• 1993

$Pr_{15}Fe_{77}B_{8}$ 조성의 합금을 Ar분위기에서 유도용해로를 이용하여 주조하 였다. 이 합금을 석영관에 넣어 고주파 유도로를 이용하여 용해한 후 0.6 nm의 분출구를 통해 회전하는 Cu wheel위에 분사하여 비본형태로 제조하였다. 이 리본을 열간변형하여 결정방향성을 주었는데 이를 위 해 먼저 $680^{\circ}C$에서 $21.8\;kg/mm^{2}$의 압력으로 hot-press하여 92%의 densification을 갖는 시편을 얻을 수 있었다. 이 시편을 다양한 조건하에서 die-upset을 행하였다. 변형율이 높을 수록 $_{i}H_{c}$는 저하되었으나, $B_{r}$은 현저하게 증가되었으며, XRD 분석 결과(006)면에서의 회절강도가 증가되었다. 따라서 압축방향으로 자화용이축이 형성되었음을 알 수 있었다. Die-upset시의 변형속도가 빠를 수록 $_{i}H_{c}$는 증가되었으나, $B_{r}$은 감소되었다. 가공온도에 따른 $B_{r}$의 변화는 $750^{\circ}C$ 까지 상승한 후 감소되었다. 이 조성의 $4{\pi}M_{s}$는 11.8 kG였고 $750^{\circ}C$에서 0.05 mm/sec의 가공속도로 변형률 0.8로 die-upset한 경우에는 $B_{r}$이 11.0 kG로 우수한 자기이방성을 가지고 있으나, die-upset후에 $_{i}H_{c}$가 낮은 문제점이 있다.

• 한국태양에너지학회 논문집
• /
• 제34권1호
• /
• pp.98-104
• /
• 2014

Photovoltaic (PV) cell is considered as one of the finest ways to utilize the solar power. A study of improving solar cell's efficiency is important because the lifetime of solar cell is determined by photovoltaic module technology. Therefore, oxidation (and/or corrosion) of solder materials will be one of the primary yield and long-term reliability risk factor. Recently, the development of lead-free solder alloy has been done actively about lead-free solder alloys of the thermodynamic and mechanical properties. However, the oxidation behavior have rarely been investigated In this study, the oxidations of 60 wt% Sn-40 wt% Pb, 62 wt% Sn-36 wt% Pb -2 wt% Ag, 50wt% Sn-48 wt% Bi-2 wt% Ag alloys for the interconnect ribbon after exposure in atmosphere at $100^{\circ}C$ for several times were investigated. The wettability of 62 wt% Sn-36 wt% Pb-2 wt% Ag and 50 wt% Sn-48 wt% Bi-2 wt% Ag solders was also studied to compare with that of 60 wt% Sn-40 wt% Pb alloy. The results howed that the zero cross time and the wetting time of 50 wt% Sn-48 wt% Bi-2 wt% Ag solder were better than other two samples. The surface of tested samples was analyzed by XPS. The XPS result showed that in all samples, SnO grew first and then the mixture of SnO and $SnO_2$ was detected. $SnO_2$ grew predominantly for the long time aging. Moreover XPS depth profile analysis has found surface enrichment of tin oxide.

• 열처리공학회지
• /
• 제14권3호
• /
• pp.160-166
• /
• 2001

The change of ribbon geometry, microstructure and shape recovery with Mn contents, wheel speed and various annealing temperature have been studied in Fe-X%Mn-5Cr-5Co-4Si (X%=15, 20, 24) shape memory alloy (SMA) ribbons rapidly solidfied by single roll chill-block melt-spinning process. The thickness and width of melt-spun ribbons are reduced, results in refining and uniformalizing grains with increasing wheel speed. In the ribbons melt-spun at a wheel speed of 15m/sec, both ${\varepsilon}$ and ${\alpha}^{\prime}$martensites are formed in ribbon 1 (15.5wt%Mn), while only ${\varepsilon}$ martensite is revealed in ribbon 2 (20.2wt%Mn) and ribbon 3 (23.5wt%Mn). The volume fraction of ${\varepsilon}$ martensite is decreased with increasing Mn contents, and those of ${\varepsilon}$ as well ${\alpha}^{\prime}$martensites are increased due to thermal stress relief and grain growth with increasing annealing temperature. Ms temperatures of the ribbons 1, 2 and 3 are fallen with increasing Mn contents. $M_s$ temperatures of the ribbons 1, 2 and 3 annealed at $300^{\circ}C$ for 3 min are risen abruptly, but are nearly constant even at higher annealing temperature, i.e., 400, 500 and $600^{\circ}C$ for 3 min. Shape recovery of the ribbons 1, 2 and 3 increased 30%, 52% and 69% with Mn contents, respectively. Shape recovery of ribbon 1 (15.5wt%Mn) formed ${\varepsilon}$ and ${\alpha}^{\prime}$martensites decreased because of the presence of ${\alpha}^{\prime}$martensite but those of ribbon 2 (20.2wt%Mn) and ribbon 3 (23.5wt%Mn) formed ${\varepsilon}$ martensite increased with increasing annealing temperature.

• 한국자기학회지
• /
• 제5권5호
• /
• pp.864-873
• /
• 1995

비정질 $Fe_{73.5}Cu_{1}Nb_{3}Si_{16.5}B_{6}$ 리본을 DSC 곡선상의 최초 발열반응 전 후의 온도인 $500^{\circ}C$ 및 $552^{\circ}C$에서 열처리하여 열처리 시간에 따른 초미립상의 생성 과정을 뫼스바우어 분광법으로 분석하였다. 열처리된 시료에 생성된 결정상은 대부분 $DO_{3}Fe-Si$이었으며, $t-Fe_{3}B$로 추정되는 강자 성상도 소량 확인되었으며, 비정질상도 잔류하여 공존함을 확인하였다. $DO_{3}Fe-Si$내의 Si 조성 즉, Si/(Fe+Si)는 $500^{\circ}C$ 60분 열처리에서 0.218 이었으며, $552^{\circ}C$ 10분 열처리에서 0.222이었다. 열처리 시간이 120분이 될 때까지 이들 두 값은 감소한 후 계속된 열처리에서 0.210으로 거의 일정하게 유지되었다. 열처리 시간 에 따른 Si 조성의 변화는 초미세자기장과 이성질체이동의 변화를 유발시킨 것으로 분석할 수 있었다. 즉, Fe-Si의 평균초미세자기장의 증가와 평균이성질체이동의 감소는 Si 조성의 증가에 기인됨을 알 수 있었다. 잔류비정질의 체적분율은 초기에 급격히 감소하여 $500^{\circ}C$와 $552^{\circ}C$ 둘 다의 열처리 온도에서 120분 이후 거의 일정해 진다. 120분 이후 Fe-Si와 잔류비정질의 체적분율의 미소한 변화에도 불구하고 잔류비 정질의 평균초미세자기장의 현저한 감소는 잔류비정질내의 Nb와 B 원소의 양의 증가에 기인된다. 결정질의 체적분율은 예측과는 달리 $500^{\circ}C$에서 180분 열처리될 경우 81 %, $552^{\circ}C$에서 960분 열처리될 경우 77 % 이었다.