• Journal of Wetlands Research
• /
• v.17 no.1
• /
• pp.1-10
• /
• 2015

The bleaching phenomenon of otter spraints is indicates that the age of spraints (fresh or old spraints). As previous studies on the old otter faeces (spraint) have focused only on the external changes of spraints, it has been difficult to explain the difference of the decomposition rates among old spraints. We hypothesized that the micrometeorology difference caused by various characteristics of sprainting sites such as porosity and consistency of soil could affect the extent of the decomposition rate, the solar bleaching phenomenon of spraints used as a measure of the patterns of old spraints. Sprainting sites were classified into four types (Clay, Sand, Rock and Concrete spot) and each type was divided into two groups according to the sunlight condition (Sunny site and Shady site) to measure the effect of solar radiation. Micrometeorology of the sites were evaluated by measuring temperatures and humidities of the sites during the whole season. The variations in micrometeorology of the sunny sites according to the sprainting site types were examined with correlation analyses between the factors of micrometeorology. The analyses on the bleaching phenomenon of the spraints by micrometeorology showed that the highest rate of bleaching was found at the 'Rock spot' and 'Concrete spot' of the sunny site and especially in summer, the highest rate of bleaching ($63.4{\pm}7.6%$) was found at the 'Clay spot' of the sunny sites. The lowest rate of bleaching was found at the 'Sand spot' of the sunny sites. The above findings show that the difference in bleaching rates among sprainting sites was due to the seasonal or sunny condition. In addition, we found that the differences in thermal conductivity among sprainting site characteristics have resulted in different sprainting site temperature which have affected the rate of bleaching of spraints. In conclusion, this study suggests that studies of otters on their population size and home ranges using spraints as an indirect sign, should consider the effects of sprainting site characteristics and weather conditions.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.1
• /
• pp.54-61
• /
• 2000

Amalgam, though a widely used dental material, does not bond to the tooth substrate Therefore, retentive preparation of the cavity is necessary. Such amalgam restorations, until corrosion products form and plug the margin, will show significant marginal leakage. Unless this is prevented early on, saliva and bacteria may enter the cavity causing postoperative hypersensitivity, dissolution and collapse of the restoration, discoloration of the margin and secondary caries, leading to shortened life-span of the restoration and pulpal pathosis. Recently, a method of restoration has been introduced whereby tooth material can be preserved, cavity margin can be sealed and preventive treatment of pit and fissure can be administered while retaining all the advantages of conventional amalgam restorations. Such sealed amalgams involve removing the carious lesion without extending the cavity for prevention and using pit and fissure sealants to seal cavity margins and pit and fissures to reduce microleakage. In this study, finishing of the amalgam and sealant application were performed after different intervals following of amalgam restoration to compare the microleakage of sealed and conventional amalgam restorations. Thirty bicuspids were prepared with Class V cavity preparations on the buccal and lingual surfaces. After amalgam placement, they were divided into the following groups and treated accordingly. Group 1 : Polishing after 24 hours Group 2 : Immediate sealant application without polishing Group 3 : No polishing, but sealant applied after thermocycling 500 times After treatment, the samples were thermocycled 500 times between $5^{\circ}C$ and $55^{\circ}C$ with a dwell time of 30 seconds. After thermocycling, the samples were dipped into 1% methylene blue kept in a $37^{\circ}C$ incubator at 100% humidity for 24 hours. The teeth were then embedded in resin and cut bucco-lingually along the tooth axis and observed with a stereomicroscope to determine the degree of microleakage, The following results were obtained : 1. Group 2 showed the least microleakeage, while group 1 showed the greatest. 2. Group 1 showed significantly greater microleakage compared to group 2 (p<0.05). However, no significant differences were found between group 1 and 3(p>0.05). No significant differences in microleakage were also found between cup 2 and 3(p<0.05).

• 대한공업교육학회지
• /
• v.38 no.1
• /
• pp.259-274
• /
• 2013

Culture is already deeply imbued in our lives. The furniture has become a way of life and the human became part of the culture. In this study, the aim is to explore the traditional furniture that is projected through the culture as a lifestyle. Therefore, the purpose of this study is to explore the cultural implication in Korean traditional wooden furniture. Specific research questions in this study are as follows; 1) How to reflected house structure culture at traditional woodcraft furniture? 2) How to reflected interior space culture at traditional woodcraft furniture? 3) How to projected life form style culture at traditional woodcraft furniture? 4) How to harmonize between modern life culture and traditional woodcraft furniture? In order to achieve the purpose of this study, the literature of review was used masters of Korea's traditional woodcraft furniture. To collect information of Korean traditional furniture, the furniture was selected representative pieces of Korean Joseon Dynasty and interviewed an important intangible cultural asset somokjang. Based on the explore of Korean traditional furniture, the conclusions of this study are as follows; first, in the viewpoint of house framework culture, most of traditional furniture was made u sing a narrow interior space and was to be placed in close contact with the walls, and was developed as a type of molding on the front of the furniture to pursue beauty. Second, in the viewpoint of ondol culture, traditional furniture was closed to the wall by using low height furniture and furniture legs the structure punghyeol was used to reflect the phenomena of convective heat and humidity. Third, in the viewpoint of life form culture, traditional furniture was made that sat-down at eye level configuration is proportional to its size and height and appropriately been made. And patterns reflect the wishes of most things in nature and to be blessed with longevity origin were used in the decoration of wooden furniture. Finally, in the viewpoint of modern life culture, traditional furniture is simple but not dirty, and splendid but not luxurious. So although traditional wooden furniture are in any room or place, never discouraged by the dignity.

• Journal of Nutrition and Health
• /
• v.3 no.3
• /
• pp.129-135
• /
• 1970

From the previous studies, F-P-4 formula was found to be comparable to full fat dry milk in its nutritive value and feeding performance. However, an attempt was made in order to make sure whether or not any possibility might exist, by which further improvement of nutritive quality and simultaneous reduction of product costs may be achieved. Using F-P-4 as a control, modifications were made in new formulas, F-P-5, F-P-6 and F-P-7 by reducing FPC, eliminating yeast from the mixture, and by enriching with methionine as needed. In particular, F-P-7 is completely free of FPC, hydrogenated oil and yeast. Yet, levels of total protein and fat were kept equal to those of F-P-4 in all formulas. An animal feeding test for all formulas using 10 female rats per group for 8 weeks and an infant feeding trial for F-P-5 and F-P-6 with 5 of each female infants under age of one for one month were conducted along with F-P-4 as a control. Almost the same results were obtained with F-P-4, 5 and 6, but F-P-7 showed the lowest body weight gain. FER of F-P-5 and 6 was 0.20 as was with F-P-4, while that of F-P-7 was 0.16. Acceptability to infants was excellent; growth, appearance and biochemical data were normal. As an example F-P-4 packed in 0.04mm polyethylene bags was used for storage study at $25^{\circ}C$ and relative humidity of $65{\sim}85%$ for 8 months. Although viable bacterial counts and vitamin C contents were reduced, peroxide and TBA values were increased gradually during such storage. Since there are also significant changes in color and organoleptic quality, the expected shelf life under the given conditions is considered to be about 2 months and thus further works are needed both on the product and packaging in order to improve the storage stability. Either elimination of yeast form F-P-4, that is F-P-5, or partial replacement of FPC with methionine, that is F-P-6 may well reduce material costs about 10%. Considering blending process of ingredients, F-P-5 is thus found to be the best formula developed. While F-P-7 free of FPC is inferior in its nutritive quality than that of others, but significantly superior than of rice. Furthermore, the material cost of the product can be reduced about 20% from that of F-P-4. And thus this vegetable blend is considered to be useful as a low cost supplementary food mixture for growing children.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.55 no.4
• /
• pp.339-349
• /
• 2010

The uses of the polypropylene bulk bags having the loading capacities more than 500 kg are increasing in Korea recently as a storage container for rough rice. This study was performed to obtain the basic information on the changes of temperature and relative humidity in the bulk-bag-stored high moisture rough rice during waiting for drying. At the moisture content more than 22% on wet weight basis of paddy, the bulk-bag inside temperature rose up to more than $40^{\circ}C$ and then slid down during storage. For example, in case of Hwaseongbyeo, 26.5% moisture content of rough rice (MCRR) harvested at 46 days after heading (DAH) showed $54.5^{\circ}C$ of peak temperature at 66.8 hours after bulk-bag loading, 22.5% MCRR harvested at 52 DAH exhibited $42.0^{\circ}C$ at 81.1 hours, and 19.7% MCRR harvested at 55 DAH displayed $38.9^{\circ}C$ at 119.0 hours. There were a good linear relationship between peak temperatures of bulk-bag inside and moisture contents of paddy ($r^2$=0.89 in 2005, and 0.87 in 2006), while the slope and intercept of the linear regression equation was affected by the environmental conditions such as ambient temperatures and microbial flora. The peak temperatures increased with the rate of about $2.74-3.33^{\circ}C$ per every 1% increase of moisture content at higher moisture contents of paddy than 19%. The relative humidity varied depending on bulk-bag inside temperature and rough rice moisture content, and showed the range of 94.2% to 99.9% in the central point of the bulk-bag. The results suggested that a rapid drying treatment as soon as possible was needed to produce a good quality of rice when the paddy of high moisture more than 22% on wet basis was harvested in a bulk-bag especially at high ambient temperature.

• Korean Journal of Food Science and Technology
• /
• v.4 no.4
• /
• pp.271-275
• /
• 1972

Effects of solvent extraction by immersion on the quality and storage stability of Korean rice were studied. Proportions of lipid extracted from whole grain of rice by immersing into two volumes(v/wt) of hexane and ethanol for 72 hours at room temperature were 0.41% and 0.38% respectively. Small changes of water content and hardness of rice were observed by solvent treatment. Cooking characteristics; that is, water-uptake ratio. extended volume, total solid, and starch-iodine blue test of rice was markedly changed by ethanol treatment, while little changes were observed by hexane treatment. No considerable differences in moisture sorption isotherm of rice were observed by both solvent treatments. Changes in TBA number and stale flavor appearance of rice treated with or without solvent immersion during storage at $60^{\circ}C$ showed that rice treated with hexane had best storage stability compared to ethanol treatment, while ethanol treatment of rice had better storage stability than no treatment. Similar results were noted in changes of the flavor score of cooked rice samples which were freeze dried.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.28 no.2
• /
• pp.119-126
• /
• 2012

State of problem: Cement-retained implant-supported prostheses are routinely used in dentistry. The use of high strength cements has become more popular with the increasing confidence in the stability of the implant-abutment screw connection and the high survival rates of osseointegrated implants. No clinical data on retention of metal copings using CAD/CAM. To evaluate retention of metal copings using CAD/CAM system bonded to short titanium abutment with four different cements and compare retentive strength of metal copings with sandblasting or without sandblasting before cementation. Forty titanium abutment blocks were fabricated and divided into 4 groups of 10 samples each. Forty metal copings with occlusal hole to allow for retention testing were fabricated using CAD/CAM technology. The four cements were Fujicem(Fuji, Japan), Maxcem Elite(Kerr, USA), Panavia F2.0(Kurarary, Japan) and Superbond C&B(Sunmedical, Japan). The copings were cemented on the titanium abutment according to manufacture's recommendation. All samples were stored for 24h at 37oC in 100% humidity and tested for retention using universal testing machine(Instron) at a crosshead speed of 1.0mm/min. Force at retentive failure was recorded in Newton. The mode of failure was also recorded. Means and standard deviations of loads at failure were analyzed using ANOVA and Paired t-test. Statistical significance was set at P<0.05. Panavia F2.0 provided significantly higher retentive strength than Fujicem, Maxcem Elite(P<0.05). Sandblasting significantly increased bond strength(P<0.05). The mode of failure was cement remaining principally on metal copings. Within the limitation of this study, Panavia F2.0 showed significantly stronger retentive strength than Fujicem, Maxcem Elite(p<0.05). The Ranking order of the cements to retain the copings was Panavia F2.0, Fujicem = Maxcem Elite. Sandblasting significantly increased bond strength(P<0.05). The retentive strength of metal copings on implant abutment were influenced by surface roughness and type of cements.

• Geophysics and Geophysical Exploration
• /
• v.15 no.4
• /
• pp.209-218
• /
• 2012

Repeatability and reproducibility in solid weight and effective porosity measurements have been discussed using 8 core samples with different diameters, lengths, rock types, and effective porosities. Further, the effect of temperature on the effective porosity measurement has been discussed as well. Effective porosity of each sample has been measured 7 times with vacuum saturation method with vacuum pressure of 1 torr and vacuum time of 80 minutes. Firstly, effective porosity of each sample is measured one by one, so that it can provide a reference value. Then for reproducibility check, effective porosity measurements with vacuum saturation of 2, 4, and 8 samples simultaneously have been performed. And finally, repeated measurements for 3 times for each sample are made for repeatability check. Average deviation from the reference set in solid weight showed 0.00 $g/cm^3$, which means perfect repeatability and reproducibility. For effective porosity, average deviations are less than 0.07% and 0.05% in repeatability and reproducibility test sets, respectively, which are in good agreement too. Most of porosities measured in reproducibility test lies within the deviation range in repeatability test sets. Thus, simultaneous vacuum saturation of several samples has little impact on the effective porosity measurement when high vacuum pressure of 1 torr is used. Air temperature can cause errors on submerged weight read and even effective porosity, because it is closely related to the temperature, density, and buoyancy of water. Consequently, for accurate measurement of effective porosity in a laboratory, efforts for maintaining air or water temperature constant during the experiment, or a temperature correction from other information are needed.

• Korean Journal of Food Science and Technology
• /
• v.8 no.3
• /
• pp.136-140
• /
• 1976

To investigate the preservability of Tongil, three types(rough, brown and milled rice) of Tongil and the common variety (being composed of typical varieties) in Korea were stored at a ambient and a low temperature $(15^{\circ}C)$ warehouse from April to October of each year for three years (1972-1974). The results obtained are described as follows; 1) Temperatures of atmosphere and the natural temperature warehouse changed in the same way. 2) Similar changes of relative humidity were observed in atmosphere and both warehouses. 3) Equilibrium moisture content of Tongil at $25^{\circ}C$ was 0.55 % lower in rough and brown rice. 0.33% lower in milled rice than each type of the common variety. 4) Weight loss rate in the natural temperature storage and in the low temperature storage was 1.35% and 0.74% after 6 month storage. 5) The change of fat acidity in browe rice was greater than any others (rough and milled rice). 6) Hardness of Tongil was 1.64kg higher than that of the common variety. 7) Germination rate was about the same during the low temperature storage, but that of brown of the natural temperature storage was abruptly decreased to $23%{\sim}37%$ after August. As a result, it is possible Tongil is applicable to the long-term storage of rice due to Tongil's superior preservability.

• Journal of the Korean earth science society
• /
• v.39 no.5
• /
• pp.419-435
• /
• 2018

The purpose of this study is to understand meteorological and climatological factors that have influence on the garlic product in Seosan and Taean, and to analyze the economic value according to the use of climatical information data for garlic farmers. The climatological characteristics and trends in this area are analyzed using the meteorological data at the Seosan local meteorological agency from 1984 to 2013, the national statistical data for the product of garlic from 1989 to 2013, and the scenario data for climate change (RCP 4.5 and 8.5) for the period from 2001 to 2100. The results are as follows. First, the condition of lower temperature for garlic growth in winter season is satisfied with the mean air temperature. The wind speed are lower and stronger in Seosan and Taean than other garlic area. The suitable condition for the growth of northern type of garlic shows the decreasing trend in the accumulated precipitation in May. However, the area of growing the northern type garlic in the future is likely diminished because mean air temperature, accumulated precipitation, and mean wind speed are strong in the harvest time of garlic. Second, the seedtime of the northern and southern type of garlic using climate change scenarios (RCP 4.5, 8.5) in Seosan and Taean is getting late as time passes. and the harvest time gets faster, which indicates s that the period of garlic cultivation becomes shorter from 50 days to around 90 in the next 100 years. Third, the beginning days of white rot and delia platura of garlic are estimated by applying to the meteorological algorithm using mean air temperature and soil humidity. Especially, the beginning day of white rot garlic is shown to be faster according to the scenarios of RCP 4.5 and RCP 8.5. Fourth, the product of garlic (kg/10a) shows a high correlation with the minimum air temperature of a wintering time, the mean wind speed of a wintering time, the accumulated precipitation of a corpulent time, and the mean relative humidity of corpulent time of garlic. On the other hand, the analysis of garlic product when using the meteorological information data in cultivating garlic in Seosan and Taean reveals that the economic value increases up to 9% in total.