• Geophysics and Geophysical Exploration
• /
• v.8 no.1
• /
• pp.26-33
• /
• 2005

Inversion of multi-mode surface-wave phase velocity for shallow engineering site investigation has received much attention in recent years. A sensitivity analysis and inversion of both synthetic and field data demonstrates the greater effectiveness of this method over employing the fundamental mode alone. Perturbation of thickness and shear-wave velocity parameters in multi-modal Rayleigh wave phase velocities revealed that the sensitivities of higher modes: (a) concentrate in different frequency bands, and (b) are greater than the fundamental mode for deeper parameters. These observations suggest that multi-mode phase velocity inversion can provide better parameter discrimination and imaging of deep structure, especially with a velocity reversal, than can inversion of fundamental mode data alone. An inversion of the theoretical phase velocities in a model with a low velocity layer at 20 m depth can only image the soft layer when the first higher mode is incorporated. This is especially important when the lowest measurable frequency is only 6 Hz. Field tests were conducted at sites surveyed by borehole and PS logging. At the first site, an array microtremor survey, often used for deep geological surveying in Japan, was used to survey the soil down to 35 m depth. At the second site, linear multichannel spreads with a sledgehammer source were recorded, for an investigation down to 12 m depth. The f-k power spectrum method was applied for dispersion analysis, and velocities up to the second higher mode were observed in each test. The multi-mode inversion results agree well with PS logs, but models estimated from the fundamental mode alone show f large underestimation of the depth to shallow soft layers below artificial fill.

• Journal of the Korean Geophysical Society
• /
• v.3 no.4
• /
• pp.251-260
• /
• 2000

Applicabilities of two numerical methods, the 2-dimensional and the 3-dimensional method, are evaluated to inverse test results obtained from the underwater SASW(Spectral -Analysis-of-Surface-Waves) method. As a result of this study, it has been found that the 2-dimensional method can supposed to be applicable for the cases where stiffness of soil layer increases gradually with depth, and the stiffness is relatively low. For the other cases, however, it has been concluded that the 3-dimensional method needs to be applied to determine realistic theoretical dispersion curves. An example is also shown that in situ soil profile underwater is estimated from experimental dispersion curves using the 3-dimensional method. As a results, it can be concluded that the underwater SASW method can be effectively applied to explore the underwater soil condition.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.25 no.1
• /
• pp.9-14
• /
• 2005

The angular dependence(profile) of backward radiated ultrasound was measured for glass specimens with random surface roughness using ultrasonic goniometer that ran changes the incident angle continuously. It was concluded that the roughened region had greater acoustic impedance than the unperturbed region. The comparison of backward radiations showed that the amplitude of peak and the area of radiation profile were increased with surface roughness. It was suggested from the sensitive dependence of the profile area that the profile of backward radiation could be applied to in the nondestructive evaluation of sulfate region. Inclined C-scan technique with the transducer inclined at Rayleigh angle showed the reverse of luminosity and the high signal to noise ratio so that it provided high resolution.

• The Korean Journal of Rheology
• /
• v.4 no.1
• /
• pp.52-61
• /
• 1992

초고분자량 폴리에틸렌을 파라 크실렌에 녹인 희박 용액에 전단흐름을 가해 섬유를 뽑아내는 방법에 대해 연구하였다. 표면성장이라 불리는 이 방법을 용액내에서 회전하는 rotor 의 표면에 흡착된 젤 층에, 결정성이 강한씨(seed)를 접촉시킴으로써 엉킨 분자쇄들이 전단력에 의해 신장되어 분자의 자유에너지가 증가하도록 하여 연속적으로 고강력, 고탄성 률 결정을 뽑아내게 한 것이다. 이표면성장법으로 섬유를 얻는데 있어서 결정화온도 rotor 속도, 권취속도 및 고분자 농도와 같은 결정화 변수를 변화시키면서 섬유의 물리적 성질에 미치는 영향을 관찰하였다. 이방법으로 섬유를 성장시키면 열역학적 평형온도(118.6$^{\circ}C$) 이상 인 12$0^{\circ}C$에서 성장시켰을 때 133GPa의 인장 탄성계수 3.1%의 절단신도에서 5.04GPa의 고 강력을 갖는 섬유를 얻을수 있었다. 또한 이방법에 있어서는 결정화 온도가 물리적 성질에 가장 큰 영향을 미치는 인자로 작용하였다, 고분자 농도의 영향은 0.7wt.% 이상에선 물리적 성질이 더 이상 개선되지 않았으며 오히려 장력의 증가로 불안정한 성장을 보였다. 또한 0.5wt%이하에서는 젤층의 형성이 둔화됨을 볼수 있었다. 결국 물리적 성질의 측면에서 볼 때 0.5~0.7wt%에서 최적조건을 보여주었다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.27 no.2
• /
• pp.105-114
• /
• 2007

Two-dimensional imaging of $V_s$ profile becomes more important in Korea because of the large horizontal variation of soil stiffness. To obtain a shear-wave velocity profile in geotechnical practice, various seismic nondestructive investigation methods are being frequently used. In this study, harmonic wavelet analysis of wave (HWAW) method is applied to the determination of $V_s$ profile to overcome some of weaknesses in the existing surface wave methods. HWAW method which is based on time-frequency analysis using harmonic wavelet transform has been developed to determine phase and group velocities of waves. Field testing of this method is relatively simple and fast because one experimental setup which consists of one pair of receivers is needed to determine $V_s$ profile of site. The proposed method uses the signal portion of the maximum local signal/noise ratio to evaluate the phase velocity to minimize the effects of noise, and uses single array inversion which considers receiver locations. Field tests were performed in 2 sites in order to evaluate accuracy of test method and estimate the applicability of 2-D imaging by HWAW method. Through field applications and comparison with other test results, the good accuracy and applicability of the proposed method were verified.

• Geophysics and Geophysical Exploration
• /
• v.15 no.1
• /
• pp.1-7
• /
• 2012

To evaluate methods of determining near-surface shear-wave velocities (${\nu}_s$), we derived dispersion curves of Rayleigh waves generated by both passive and active sources in Chuncheon, Korea. Microtremors were recorded for 5 minutes in each of four triangular arrays with radii of 5 ~ 40 m. Those data were analyzed using the Spatial Autocorrelation method. Rayleigh waves were also generated by a hammer source and recorded in the same area for 2 s using 24 4.5-Hz geophones. Multichannel Analysis of Surface Waves was applied to those data. Velocity spectra were derived with relatively high signal-to-noise ratios in the frequency ranges of 7 ~ 19 and 11 ~ 50 Hz for the microtremors and synthetically generated Rayleigh waves, respectively. The resultant dispersion curves were combined as one and then input to inversion to derive shear wave velocities that were compared with a lithology log from a nearby well. Shearwave velocities in the top soil and soft-rock layers are almost constant with values of 221 and 846 m/s, respectively; while the inverse-modeled ${\nu}_s$ increases linearly in the gravelly sand, cobbles, and weathered-rock layers. If rock type is classified based on shear-wave velocity, the inversion-derived boundary between weathered-rock and soft rock may be about 5 m deeper than in the well log.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.440-444
• /
• 2017

Two-dimensional hydrodynamic analysis was performed to analyze the attenuating characteristics of shock waves generated by the detonation of the bulkhead initiator. Through the interlocking analysis between HNS and HMX stacking initiator and STS bulkhead, we have precisely simulated detonation growth and pressure wave attenuation phenomena. The free surface velocity at the surface of the bulkhead was measured for quantitative comparison with the test data by VISAR. As a result, it was confirmed that the pressure attenuating pattern of the shock wave exponentially decreased according to the bulkhead thickness. The observed inflection point at the particle velocity measured over time is due to the subsequent propagation of the shock wave due to the rapid spallation of the interface between the detonator and the bulkhead.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.4
• /
• pp.241-250
• /
• 1997

The velocity dispersion of surface acoustical wave(SAW) of Si layer/mesh Au/Si substrate was measured by the frequency analysis technique of backward radiation at liquid/solid interface. The difference of backward radiation patterns depending on used transducers (2, 5, 10MHz) confirmed that the backward radiation phenomenon was caused by the energy radiation from SAW generated in surface region. An ultrasonic goniometer was constructed to measure continuously the angular dependence of backscattered intensity. The angular dependences of backward radiation(5MHz) were measured for Ni layer/Al substrate specimens that were bonded by epoxy involving different content of Cu powder. It was known that the width and pattern of backward radiation had informations such as the velocity dispersion, bonding quality and structure of surface region.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.4
• /
• pp.33-46
• /
• 2007

HWAW (Harmonic Wavelet Analysis of Wave) method, which is non-destructive method using body and surface waves, has the advantages of obtaining 2D subsurface imaging because it uses a short receiver spacing to obtain the $V_s$ profile of whole depth. Even though the reliability of HWAW method has already been verified by using the numerical simulation in the various layered models, it is very difficult to evaluate the reliability of HWAW in the field because the exact $V_s$ values of the experimental site are unknown. In this study, a model testing site where the material properties and layer information could be controlled was constructed to verify the reliability of HWAW method. The detailed geometry of the testing site was strictly measured by surveying, and 140 vertical and horizontal geophones were established at the boundary of each layer to evaluate the dynamic material properties. Using the interval travel times between the upper and lower geophones, the body wave velocities of each layer were 2 dimensionally obtained as reference data, and comparative study using HWAW method was performed. By comparing 2D Vs profile obtained by HWAW method to the reference data, the reliability of HWAW method was verified.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.4
• /
• pp.213-221
• /
• 2013

This paper introduces a mesh continuation scheme for a one-dimensional inverse medium problem to reconstruct the spatial distribution of elastic wave velocities in heterogeneous semi-infinite solid domains. To formulate the inverse problem, perfectly-matched-layers(PMLs) are introduced as wave-absorbing boundaries that surround the finite computational domain truncated from the originally semi-infinite extent. To tackle the inverse problem in the PML-truncated domain, a partial-differential-equations(PDE)-constrained optimization approach is utilized, where a least-squares misfit between calculated and measured surface responses is minimized under the constraint of PML-endowed wave equations. The optimization problem iteratively solves for the unknown wave velocities with their updates calculated by Fletcher-Reeves conjugate gradient algorithms. The optimization is performed using a mesh continuation scheme through which the wave velocity profile is reconstructed in successively denser mesh conditions. Numerical results showed the robust performance of the mesh continuation scheme in reconstructing target wave velocity profile in a layered heterogeneous solid domain.