• Aerospace Engineering and Technology
• /
• v.12 no.1
• /
• pp.94-104
• /
• 2013

In solar system, Mars which has the most similar environment with the Earth has been steadily studied for the purpose of habitable environment for the future manned exploration and settlement. During the daytime, Martian ionosphere can be used for the ground-ground communications between lander and rover through the reflection of the radio wave from ionosphere. In addition, researches about Martian ionosphere provide the link of revolution of water and atmosphere. Martian ionospheric observations were performed by the occultation experiments onboard Mariner, Mars, Viking series during early Martian explorations as well as recent Mars Global Surveyor. Low frequency radar and plasma analyzer are on board Mars Express and Viking-1, 2 lander obtained the only vertical plasma density profile during their entry phase. In this paper, we studied the characteristics of scientific payloads observing Martian ionosphere and then analyzed the usability of ionospheric research according to the communication and climate on Mars.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.5 no.1
• /
• pp.18-25
• /
• 2001

The results of systematic numerical experiments of secondary gas injection thrust vector control are presented. The effects of secondary injection system such as injection location and nozzle divergent cone angle onto the overall performance parameters such as thrust ratio, specific impulse ratio and axial thrust augmentation, are investigated. Complex nozzle exhaust flows induced by the secondary jet penetration is numerically analyzed by solving unsteady three-dimensional Reynolds-averaged Navier-Stokes equations with Baldwin-Lomax turbulence model for closure. Numerical simulations compared with the experiments of secondary air injection into the rocket nozzle of $9.6^{\cire}$ divergent half angle showed good agreement. The results obtained in terms of overall performance parameters showed that locating the secondary injection orifice further downstream of primary nozzle ensures the prevention of occurrence of reflected shock wave, therefore is suitable for efficient and stable thrust vectoring over a wide range of use.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2010.05a
• /
• pp.2032-2037
• /
• 2010

충청남도 서해안은 생태환경의 보고로서 갯벌, 사구, 해안습지 등 독특한 자연적 특성을 갖고 있는 지역이다. 그러나 다른 지역에 비해 대규모 간척 및 매립으로 인한 해양생태계 피해에 현저히 노출되어 있으며, 서해안 지역은 최근 산업화 및 관광권화가 진행되며 무분별하게 설치된 호안구조물은 그 기능을 상실하여 상당수가 설치전보다 오히려 서해안의 독특한 환경성과 관광성을 악화시키고 있어 서해안 특성을 고려한 대책이 요구된다. 본 연구에서는 서해안의 특성을 고려한 환경친화적 연안 호안구조물 리모델링을 위해 서해안의 침식특성에 대하여 분석하고자 한다. 분석 방법은 충청남도 서해안의 4개 시 군 29개 지점을 대상으로 1년여에 걸쳐 수행된 현장조사 결과를 바탕으로 서해안의 침식 현황을 파악하고, 기 조사된 서해안 지역의 침식에 대한 자료를 바탕으로 침식원인을 유형화하였다. 조사 분석결과 서해안의 대표적인 침식유형은 직립 급경사 호안구조물의 반사파로 인한 해빈침식(자갈화), 사구 토사포락, 직립 급경사 호안구조물 저면 세굴에 의한 호안구조물 붕괴, 방파제 설치에 의한 침식 등 대표적인 4가지 유형으로 분류할 수 있으며, 침식 유형별 발생지점 수는 총 29개 지점 중 각각 19개 지점, 13개 지점, 5개 지점, 4개 지점에서 나타났다. 이는 호안구조물이 미설치된 곳은 사구 토사포락에 의한 침식 발생빈도가 높았고, 반면에 호안구조물이 설치된 곳에서는 호안구조물의 기능 상실로 인한 해빈침식의 발생빈도가 높은 것으로 나타났다. 또한 조사지점으로 선정하였던 29개 모든 지점에서 토사유실로 인한 자갈화가 진행되어 서해안의 갯벌, 사구, 해안습지 등이 유실되고 있는 것으로 나타났으며, 이는 최근 기후변화에 따른 해수면 상승과 서해안 특성을 고려하지 않은 정형화된 직립 급경사 호안구조물의 역효과로 피해가 발생된 것으로 나타났다.

• Journal of the Korean earth science society
• /
• v.29 no.7
• /
• pp.559-566
• /
• 2008

Ground shaking recorded during the January 20, 2007, $M_L$ 4.8 Odaesan earthquake (Korea) were used to investigate the role of the crustal structure in producing a strong ground motion, which includes the identification of the phases responsible for the strong ground motion and their implications for seismic hazard assessment. Analyses of strong-motion data together with waveform simulation revealed that critical and post-critical reflections from the crust-mantle boundary are responsible for the abnormal ground motions. This result demonstrates that the crustal structure should be taken into consideration in studies of seismic hazard mitigation even in the areas of relatively low seismicity.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.10 no.1
• /
• pp.1-9
• /
• 1998

Among the phenomena of water-wave transformation, the wave diffraction is prominent for waves insidc the harbor. It is important to study how accurately the diffraction can be resolved by the numerical model. Three parabolic mild-slope equations, i.e., simple, wide-ang1e, three-parameter parabolic equations, are compared in view of the diffraction of water-waves around a semi-infinite breakwater. To avoid reflections at lateral boundaries, we apply the perfect boundary condition of Dalrymple and Martin (1992) in case of simple parabolic equation. The numerical results for the case of a semi-infinite breakwater are compared with the analytical solution of Penney and Price (1952). All the results are very accurate when waves attack the breakwater normally. When waves attack the breakwater obliquely, however, the simple parabolic equation yields the worst solution and the three-parameter parabolic equation yields the most accurate solution.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.2
• /
• pp.11-16
• /
• 2006

An experimental study of the transonic flows over NACA and double wedge airfoils was conducted with a shock tube. The configuration of test section with a slotted wall and chamber was designed and tested to minimize wall and reflected shock wave effects and use the shock tube as simple and less costly wind tunnel generating the relatively high Reynolds numbers transonic flow. Transonic airfoil flows at hot gas Mach numbers of 0.80~0.84, Reynolds number of about $1.2{\times}10^6$ on airfoil chord length and angles of attack of $0^{\circ}$ and $2^{\circ}$ were visualized with the shadowgraph method. The shock wave profiles on the airfoils were compared with the corresponding results from the conventional transonic wind tunnel tests. The experimental results showed that present shock tube exhibited the proper performance characteristics as transonic wind tunnel for tested Mach number range and airfoils.

• Journal of Satellite, Information and Communications
• /
• v.1 no.1
• /
• pp.59-64
• /
• 2006

The broadband power detector for power amplitude envelope detection of the direct-conversion Six-port output signal was designed and implemented in this paper. The power detector should be linearly operated to produce the linear amplitude and phase signal for input RF signals in required broadband frequency range. The power detector should be designed under conditions of matching circuit with low VSWR, which protect unbalanced phase signal from reflection signal due to mismatch between the output port of a six-port and the input port of a power detector. The designed power detectors, which were implemented in L-band with 50 ohm matching and Ku-band with multiple LC matching circuits and isolator, respectively, were analyzed in viewpoints of the utilization as a power detector of direct conversion Six-port. The dynamic range of designed power detectors were also measured and rvaluated as a power detector of Six-port circuit.

• Journal of the Korean Institute of Gas
• /
• v.12 no.2
• /
• pp.92-98
• /
• 2008

A combination of the instrumented indentation and 3D morphology measurement has been tried in order to perform a real-time property measurement of degraded materials in gas pipelines; three-dimensional indent morphologies were recorded using a reflective laser scanner after a series of insturmented indentations on three metallic specimens. Dimensions of the permanent deformation zone and contact boundary were analyzed from the cross-sectional profile over an remnant indent and used for estimating yield strength and hardness, respectively. Estimated yield strength was comparable with that from uniaxial tensile test and actual hardness implying material pile-up effects was lower than the calculated value from indentation curve by $20{\sim}30%$. It means that this 3D image analysis can explain the material pile-up effects on the contact properties. Additionally, a combined system of indentation and laser sensor was newly designed by modifying a shape of the indentation loading fixture.

• Journal of Korea Water Resources Association
• /
• v.51 no.10
• /
• pp.853-862
• /
• 2018

An adaptive cut-cell grid based 2D inundation analysis model, K-Flood, is developed in this study. Cut cell grid method divides a grid into a flow area and a non-flow area depending the characteristics of the flows. With adaptive mesh refinement technique cut cell method can represent complex flow area using relatively small number of cells. In recent years, the urban inundation modeling using high resolution and fine quality data is increasing to achieve more accurate flood analysis or flood forecasting. K-Flood has potential to simulate such complex urban inundation using efficient grid generation technique. A finite volume numerical scheme of second order accuracy for space and time was applied. For verification of K-Flood, 1) shockwave reflex simulation by circular cylinder, 2) urban flood experiment simulation, 3) Malpasset dam collapse simulation are performed and the results are compared with observed data and previous simulation results.

• Journal of Energy Engineering
• /
• v.8 no.4
• /
• pp.540-545
• /
• 1999

The classical Fourier heat conduction equation is invalid at temperatures near absolute zero or at very early times in highly transient heat transfer processes. In such situations, a hyperbolic equation model for heat conduction based on the modified Fourier law is introduced because the wave nature of heat propagation becomes dominant. The Fourier model and the hyperbolic model for heat conduction are analyzed by using the Green's function technique together with the integral transform. Analytical expressions for the heat flux and temperature distributions in a finite slab subjected to a periodic surface heating at one of its surfaces are presented and the results obtained from each model are compared with each other. The thermal wave implied b the hyperbolic model is shown to travel through a medium and to reflect back toward the origin at the other insulated surface. On the other hand, the heat by the Fourier model propagates at an infinite speed instantaneously after a thermal disturbance is felt throughout the medium.