• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.3
• /
• pp.306-311
• /
• 2017

This paper deals with the design optimization of the kinematic characteristics of an automotive suspension system. The kinematic characteristics of the suspension determine the attitude of the wheels, such as the toe and camber, which not only relates to tire wear during driving, but also greatly affects the control of the vehicle and its stability, which corresponds to the motion performance of the vehicle. Therefore, it is very important to determine the characteristics of the suspension mechanism at the initial stage of the design. In this study, a displacement analysis is performed to determine the kinematic properties of the suspension for the McPherson strut suspension. For this purpose, a set of constraint equations for the joints constituting the suspension mechanism was established and a program was developed to solve them. We also used ADS, a design optimization program, to obtain the desired kinematic characteristics of the suspension. As the design variables for optimization, we used the coordinates of the hard points, which are the points of attachment of the suspension to the vehicle body, and are defined as the summation of the toe-in for the up and down movement of the wheel as the objective function. As the constraint functions, the maximum camber angle and minimum roll center height, which are design requirements, are considered. As a result of this study, it was possible to determine the optimal locations of the hard points that satisfy both constraint functions and minimize the change of the toe-in.

• Composites Research
• /
• v.30 no.1
• /
• pp.26-34
• /
• 2017

This research presents studies on an improved method to predict the thermal conductivity of woven fabric composites, the effects of geometric structures of woven fabric composites on thermal conductivity, and structural optimization to improve the thermal conductivity using a genetic algorithm. The geometric structures of woven fabric composites were constructed numerically using the information generated on waviness, thickness, and width of fill and warp tows. Thermal conductivities of the composites were obtained using a thermal-electrical analogy. In the genetic algorithm, the chromosome string consisted of thickness and width of the fill and warp tows, and the objective function was the maximum thermal conductivity of woven fabric composites. The results confirmed that an improved method to predict the thermal conductivity was built successfully, and the inter-tow gap effect on the composite's thermal conductivity was analyzed suggesting that thermal conductivity of woven fabric composites was reduced as the gap between tows increased. For structural design, optimized structures for improving the thermal conductivity were analyzed and proposed. Generally, axial thermal conductivity of the fiber tow contributed more to thermal conductivity of woven fabric composites than transverse thermal conductivity of the tows.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.270-273
• /
• 1998

2차 세계대전 중(1943년) 쟈크 이브 쿠스토우(J.I.Cousteau)와 가그논(E. Gagnon)둥에 개발된 현대식 SCUBA는 전세계적으로 새로운 레크레이셔널 다이빙이라고 하는 새로운 스포츠를 창조했다. 현재 미국에서는 다이빙이 점점 안전해지면서 스쿠바 다이빙을 배우고 즐기는 사람이 많이 늘고 있으며 연간 60만명 이상이 캐리비안섬으로 다이빙을 하기위해 여행을 간다고 한다[1].(중략)

• Journal of Korean Society of Steel Construction
• /
• v.11 no.3 s.40
• /
• pp.319-327
• /
• 1999

This study makes mechanism of the fatigue strength improvement by the processing of weld toe clear for the vertical cross rib specimens which was made fillet weld joint, also it proposes to the appropriate later processing. As a result of tension fatigue test, the fatigue strength improvement could have been seen in later processed specimens than as-weld specimens. Especially fatigue crack initial life $N_c$ increased in specimens which processed grinder after hammer-peening. Also, fatigue crack propagation life $N_p$ improved more in hammer-peening specimens than as-weld or TIG specimens. It thinks that $N_c$ is because of the geometrical shape of weld toe, i.e. the relaxation of the stress concentration and also that $N_p$ is because the big compression residual stress which was introduced in the surface by hammer-peening is restraining the propagation of fatigue crack.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.4_1
• /
• pp.137-150
• /
• 1992

A complete solution, exact to second-order, for wave motion forced by a hinged-wavemaker of variable-draft is presented. A solution for a piston type wavemaker is also obtained as a special case of a hinged-wavemaker. The laboratory waves generated by a plane wave board are shown to be composed of two components; viz., a Stokes second-order wave and a second-harnomic free wave which travels at a different speed. The amplitude of the second-harmonic free wave is relatively large in shallow water and decreases to less than 10% of the amplitude of the primary wave in deep water. Wavemakers with relatively deeper draft (i.e., hinged near the bottom) generate the free waves of smaller amplitude in shallow and intermediate water depths than the wavemakers with shallow draft. However, the opposite is predicted by theory in deep water.

• Composites Research
• /
• v.28 no.5
• /
• pp.249-253
• /
• 2015

This paper reports a study on a method for achieving lightweight thermoplastic laminate composites referred to as tow spreading technology. Thickness of an unspread 12 K carbon fiber tow is reduced by increasing the tow width from 7 mm to 20 mm. The polypropylene (PP) film was used to stabilize and impregnate the spread tow, covering it into a partially consolidated prepreg: 12 K carbon fiber spread tow/PP. Laminates were fabricated from the spread tow prepreg and control laminate composites were produced from unspread tow prepreg consisting of 12 K carbon fiber and PP. The void content, tensile and flexural properties of the composite laminates were investigated. Consequently, the spread tow laminate composite exhibited lower void content and improved mechanical properties.

• Korean Journal of Food Science and Technology
• /
• v.23 no.5
• /
• pp.610-613
• /
• 1991

The changes of volatile components of cooked rice during storage at $70^{\circ}C$ for 5 hr were investigated. Among more than 100 volatile components of fresh cooked rice, the predominant one was hexanal followed by nonanal, acetone, pentanal, butanal, heptanal, octanal and toluene. These eight components comprised about 55% of the total volatile, which was decreased by half after one hour storage. The amount of major volatile components in Tongil type rice was higher than Japonica rice, but the decrease of volatiles during storage was faster in the former.

• Physical Therapy Korea
• /
• v.9 no.4
• /
• pp.1-11
• /
• 2002

본 연구의 목적은 이중과업 방법론(dual task methology)을 사용해서 젊은 사람과 노인을 대상으로 독립된 두 사건(two separate concurrent events)을 동시에 수행하는데 요구되는 주의력에 대한 분석과 노인에서의 특징적 차이를 찾는 것이다. 본 실험은 대상자가 힘판(force plate) 위에서 장애물(10cm) 보행시에 경피자극(cutaneous stimulation)에 대하여 마이크로 스위치(micro-switch)를 사용하여 반응하면서 시행되었다. 힘판과 시간(temporal events) 그리고 반응시간(reaction time)에 관한 자료들은 1000 Hz의 주파수로 수집되었다. 반응시간은 대상자들이 서 있는 상태(baseline) 장애물 보행시(dual task)에서 수집되었다. 반응시간은 아중과업 조건에서 대상자 모두에게서 긴 것으로 나타났으며 특히 노인에서 정상 성인보다 반응시간이 긴 것으로 나타났다. 이중과업 조건 하에서 노인 대상자가 정상 성인에 비해 발가락이 장애물에 닫지 않고 통과할 수 있는 공간, 즉 토우 클리어런스( toe-clearance)와 슬관전 굴곡(knee flexion) 각도가 훨씬 큰 것으로 나타났다. 이중과업 조건하에서 모든 대상자가 족관절 배측굴곡(ankle dorsiflexion) 각도를 감소시키는 것으로 나타났다. 노인들은 젊은 대상자들보다 훨씬 더 긴(124 ms) 유각시간을 보여 주었으며 정상 장애물 보행시 유각 시간은 이중과업보다 50 ms 긴 것으로 나타났다. 이러한 보행 특성의 차이는 노인대상자들이 젊은 대상자들보다 장애물 보행시에 이중과업의 영향을 더 받았기 때문인 것으로 판단된다. 이중 과업 시행시 이러한 토우 클리어런스의 감소와 장애물 통과시에 보행 속도의 증가는 아마도 낙상의 가능성을 증가시키는 요인이 될 수 있는 것으로 보여진다. 본 연구의 결과는 다중과업(multitasks)을 필요로 하는 보행 훈련 프로그램(gait training program)의 개발과 시행에 있어서 기초적인 자료를 제공할 수 있는 것으로 보여진다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.23 no.3
• /
• pp.220-226
• /
• 2003

This paper presents the result of an investigation on the application of the acoustic emission method to the monitoring of fatigue crack initiation, growth and track location in welded joints. Fatigue test was carried out for a typical fillet welded joint of ship structure. AE parameter such as ring down count was analyzed in time domain and crack locations were examined by source location and cluster option which is one of the functions of AE signal processor The usability of AE mettled was confirmed for the detection of the initiation and location of through crack.

• Korean Journal of Remote Sensing
• /
• v.13 no.2
• /
• pp.133-150
• /
• 1997

The purpose of this paper is to develop an algorithm of classification and interpretation of seafloor based on side scan sonar data. The algorithm consists of mosaicking of sonar data using navigation data, correction and compensation of the acouctic amplitude data considering the charateristics of the side scan sonar system, and segmentation of the seafloor using digital image processing techniques. The correction and compensation process is essential because there is usually difference in acoustic amplitudes from the same distance of the port-side and the starboard-side and the amplitudes become attenuated as the distance is increasing. In this paper, proposed is an algorithm of compensating the side scan sonar data, and its result is compared with the mosaicking result without any compensation. The algorithm considers the amplitude characteristics according to the tow-fish's depth as well as the attenuation trend of the side scan sonar along the beam positions. This paper also proposes an image segmentation algorithm based on the texture, where the criterion is the maximum occurence related with gray level. The preliminary experiment has been carried out with the side scan sonar data and its result is demonstrated.