• Clean Technology
• /
• v.25 no.2
• /
• pp.107-113
• /
• 2019

Numerical model that considered the shrinking core model and elutriation and degradation of particles was developed to predict selective chlorination of ilmenite and carbo-chlorination of $TiO_2$ in a two stage fluidized bed chlorination furnace. It is possible to analyze the fluidized bed chlorination reaction to be able to reflect particle distribution for mass balances and the chlorination reaction. The numerical model showed an accuracy with error less than 6% compared with fluidized bed experiments. The chlorination degree with particle size change was greater with a smaller particle size, and there was a 100 min difference to obtain a chlorination degree of 1 between $75{\mu}m$ and $275{\mu}m$. This was not shown to such a great extent with variation of temperature ($800{\sim}1000^{\circ}C$), and there was only a 10 min difference to obtain a chlorination degree of 0.9. In the first selective chlorination process, the mass reduction rate approached to the theoretical value of 0.4735 after 180 min, and chlorination changed the Fe component into $FeCl_2$ or $FeCl_3$ and showed nearly 1. In the second carbo-chlorination process, the chlorination degree of $TiO_2$ approached 0.98 and the mass fraction reached 0.02 with conversion into $TiCl_4$. In the first selective chlorination process, 98% of $TiO_2$ was produced at 180 min, and this was changed into 99% of $TiCl_4$ after an additional 90 min. Also the mass reduction rate of $TiO_2$ was reduced to 99% in the second continuous carbo-chlorination process.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.4
• /
• pp.423-428
• /
• 2010

Electrostatic precipitators (ESPs) used currently in industries for removing fine particles from semiconductors have to be made of expensive anticorrosive metallic materials in order to maintain their particle-removal performance. To satisfy the economical demands of industries, a novel ESP was developed; in this ESP, the charger is made of carbon fibers and collection plates consist of PET films among which an aluminum sheet is inserted. The ESP was evaluated by changing the voltages applied to the chargers and collection plates, flow rates, and number of charging channels. KCl particles with mean diameters of 100 nm were used, and a scanning mobility particle sizer was used to measure the changes in particle number concentrations upstream and downstream of the ESP. The experimental results showed that more than 90% of the particles were removed by using the ESP containing ionizers with nine channels and 65-mm collection plates at $500\;m^3/hr$ when voltages of 7 kV and 10 kV were applied to the ionizers and collection plates, respectively.

• Korean Chemical Engineering Research
• /
• v.49 no.3
• /
• pp.372-380
• /
• 2011

Char gasification is affected by operating conditions such as reaction temperature, reactants gas partial pressure, total system pressure and particle size in addition to chemical composition and physical structure of char. The aim of the present work was to characterize the effect of coal particle size on $CO_{2}$ gasification of chars prepared from two different types of bituminous coals at different reaction temperatures(1,000-$1,400{^{\circ}C}$). Lab scale experiments were carried out at atmospheric pressure in a fixed reactor where heat was supplied into a sample of char particles. When a flow of $CO_{2}$(40 vol%) was delivered into the reactor, the char reacted with $CO_{2}$ and was transformed into CO. Carbon conversion of the char was measured using a real time gas analyzer having NDIR CO/$CO_{2}$ sensor. The results showed that the gasification reactivity increased as the particle size decreased for a given temperature. The sensitivity of the reactivity to particle size became higher as the temperature increases. The size effects became remarkably prominent at higher temperatures and became a little prominent for lower reactivity coal. The particle size and coal type also affected reaction models. The shrinking core model described better for lower reactivity coal, whereas the volume reaction model described better for higher reactivity coal.

• Journal of the Korean Wood Science and Technology
• /
• v.43 no.3
• /
• pp.381-389
• /
• 2015

In this study, the effects of moisture content and particles size of ground particles of torrefied larch chips on the pelletizing process were investigated depending on torrefaction conditions ($220^{\circ}C$-50 min, $250^{\circ}C$-50 min, $250^{\circ}C$-120 min). The moisture content in the torrefied chip decreased to 0.69~1.75%, while ash content and calorific value increased compared to untreated chip. In addition, weight loss significantly increased during torrefaction due to hemicellulose degradation. The carbon content in torrefied larch chip increased compare to untreated larch chip, while the hydrogen and oxygen contents decreased. The lignin and glucan contents in torrefied larch chip increased with increasing severity of the torrefaction condition, while hemicellulose decreased. In the particle size distribution of ground particles of torrefied larch chip, larch torrefied at severe conditions was found to produce smaller particles (~1 mm) than that of the larch torrefied at mild conditions. Macropore (over $500{\AA}$) in the torrefied particle was produced during torrefaction. During the pelletizing using ground particles of torrefied larch chip, the pressure needed in pelletizing decreased and pellet length increased with increasing moisture content, regardless of the particle size.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.12
• /
• pp.608-613
• /
• 2019

NOx (Nitrogen oxide) in the exhaust gas from vehicle engines is considered one of the most harmful substances in air pollution problems. NOx is made when combustion occurs under high temperature conditions and EGR (exhaust gas recirculation) is normally used to lower the combustion temperature. As the EGR ratio increases, the NOx level becomes low, but a high EGR ratio makes the combustion unstable and causes further air pollution problems, such as CO and unburned hydrocarbon level increase. This study showed that fuel droplets could move more freely by the radiation of sonic wave for the stable combustion. In addition, the engine performance improved with increasing EGR ratio. As a basic study, the effect of sonic wave radiation on the velocity of fuel droplets was studied using CFD software. The results showed that the velocity of small droplets increased more under high frequency sonic wave conditions and the velocity of the large droplets increased at low frequency sonic wave conditions. In addition, an engine analysis model was used to study the effects of the increased combustion stability. These results showed that a 15% increase in EGR ratio in combustion resulted in a 45% decrease in NOx and a 10% increase in thermal efficiency.

• Journal of the Korean Electrochemical Society
• /
• v.12 no.3
• /
• pp.282-286
• /
• 2009

The synthesis and characterization of catalysts supported on multi-walled carbon nanotubes (CNTs). $Pt/Au/TiO_2$ is added to a CNTs(cabon nano tube) carbon support to improve the performance of a direct methanol fuel cell. XRD and SEM showed that uniform anatase $TiO_2$ and Pt/Au particles were about 200 nm and 20${\sim}$25 nm in diameter. The composite catalyst activities were measured by cyclic voltammetry (CV), demonstrating that it is more promising for use in fuel cells.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.248-248
• /
• 2010

리튬이온 2차전지의 대체 양극 후보 물질인 $LiFePO_4$를 합성하기 위하여 출발원료로 $Li_2CO_3$, $Fe_2O_3$, $NH_4H_2PO_4$를 사용하여 볼밀 방법으로 혼합 분쇄한 후 열처리를 실시하였다. 합성 시에 3가 Fe를 2가로 환원시키기 위하여 $C_{12}H_{22}O_{11}$(흑설탕)을 출발원료와 함께 5 ~ 12 wt%로 나눠서 첨가하였다. 합성 후 XRD로 결정구조의 양질성을 확인하였고. FE-SEM으로 나노미터 크기의 구형 입자를 관찰하였다. XRF를 이용하여 3 ~ 10 wt%의 탄소 잔량을 확인하였다. 전기화학적 특성을 충 방전시험기로 평가한 결과, 8wt%의 탄소원을 첨가한 $LiFePO_4$에서 가장 좋은 수명 특성을 얻었고, 최대 145 mAh/g의 방전용량을 얻었다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.28 no.2
• /
• pp.215-222
• /
• 2004

Synthesis of multi-walled carbon nanotubes on a nickel-nitrate-deposited substrate using an ethylene fueled inverse diffusion flame was illustrated. The deposition of nickel-nitrate particles on substrates was used for the smaller-diameter nanotubes than those formed in our previous studies. Also the effect of temperature variations on the size of formed nanotubes was investigated. The diameters of formed multi-walled carbon nanotubes were ranging from 15 to 100 nm in the several radial locations. In case of using a nickel-nitrate-deposited substrate, the smaller-diameter carbon nanotubes were synthesized than those in case of using the substrate with melted nickel-nitrate. In the formation region of carbon nanotubes, the diameter of formed nanotubes was tend to be decrease as the radial distance form the flame center was increased, that is the decreased substrate temperature.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.812-818
• /
• 2004

This study has been undertaken with objective of studying the mechanism and condition of formation of hexagonal boron nitride from reduction of boric okide in the presence of carbon under nitrogen atmosphere. It was found that the formation of hexagonal boron nitride was started at 1400$^{\circ}C$ and almost completed its conversion at 1550$^{\circ}C$. The morphology of boron nitride synthesized in this study was very fine and platelet. It was considered as reaction pathway of hexagonal boron nitride that boron oxide was reduced to born and evaporated by activated carbon, and then it was reacted with nitrogen.

• Transactions of the Korean hydrogen and new energy society
• /
• v.14 no.3
• /
• pp.247-257
• /
• 2003

To investigate the effect of preparing condition on the physical properties of carbon nanotubes suitable for optical applications, carbon nanotubes were synthesized by thermal chemical vapor deposition using Ni particles as a catalyst on stainless steel substrate and acetylene as a reactant gas. To examine the physical and optical properties, SEM, TEM, Ram an, UV-visible, and photoluminescence spectroscopy were used. The physical properties of carbon nanotubes such as diameter, degree of growth density and morphology were closely related to such experimental conditions as Ni particle size, growing pressure, and etching condit on of Ni particles, it appeared from the light absorbance and photoluminescence spectra of carbon nanotube mixture prepared with an addition of a photopolymer, P3HT(Poly(3-hexylthIop hene)) that carbon nanotube could do a role as a kind of electron acceptor for solar cell application.