• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2000.09a
• /
• pp.201-210
• /
• 2000

Rock bridge in rock masses can be considered as one of several types of opening-mode fractures, and also it has been known to have a great influence on the stability of structures in rock mats. In the beginning of researching a rock bridge it used to be studied only in characteristics of its behavior, as considering resistance of material itself. However the distribution pattern of rock bridges, which can affect the stability of rock structures, is currently researched with a fracture mechanical approach in numerical studies. For investigating the effect of rock bridges on the development pattern of hydraulic fractures, the author analyzed numerically the stress state transition in rock bridges and their phenomena with a different pattern of the rock bridge distributons. From the numerical studies, a two-crack configuration could be defined to be representative of the most critical conditions for rock bridges, only when cracks are systematic and same in their length and angle. Moreover, coalescence stresses and onset of propagation stresses could be known to increase with decreasing s/L ratio or increasing d/L ratio. The effect of pre-existing crack on hydraulic fracturing was studied also in numerical models. Different to the simple hydraulic fracturing modeling in which the fractures propagated exactly parallel to the maximum remote stress, the hydraulic fractures with pre-existing cracks dial not propagate parallel to the maximum remote stress direction. These are representative of the tendency to change the hydraulic fractures direction because of the existence of pre-existing crack. Therefore s/L, d/L ratios will be identical as a function effective on hydraulic fractures propagation, that is, the $K_{I}$ vague increase with decreasing s/L ratio or increasing d/L ratio and its magnification from onset to propagation increases with decreasing s/L ratio. The scanline is a commonly used method to estimate the fracture distribution on outcrops. The data obtained from the scanline method can be applied to the evaluation of stress field in rock mass.s.

• Tunnel and Underground Space
• /
• v.10 no.3
• /
• pp.447-456
• /
• 2000

Rock bridge in rock masses can be considered as one of several types of opening-mode fractures, and also it has been known to have a great influence on the stability of structures in rock mass. In the beginning of researching a rock bridge it used to be studied only in characteristics of its behavior, as considering resistance of material itself. However the distribution pattern of rock bridges, which can affect the stability of rock structures, is currently researched with a fracture mechanical approach in numerical studies. For investigating the effect of rock bridges on the development pattern of hydraulic fractures, the author analyzed numerically the stress state transition in rock bridges and their phenomena with a different pattern of the rock bridge distributions. From the numerical studies, a two-crack configuration could be defined to be representative of the most critical conditions for rock bridges, only when cracks are systematic and same in their length and angle. Moreover, coalescence stresses and onset of propagation stresses could be known to increase with decreasing s/L ratio or increasing d/L ratio. The effect of pre-existing crack on hydraulic fracturing was studied also in numerical models. Different to the simple hydraulic fracturing modeling in which the fractures propagated exactly parallel to the maximum remote stress, the hydraulic fractures with pre-existing cracks did not propagate parallel to the maximum remote stress direction. These are representative of the tendency to change the hydraulic fractures direction because of the existence of pre-existing crack. Therefore s/L, d/L ratios will be identical as a function effective on hydraulic fractures propagation, that is, the K$_1$ value increase with decreasing s/L ratio or increasing d/L ratio and its magnification from onset to propagation increases with decreasing s/L ratio. The scanline is a commonly used method to estimate the fracture distribution on outcrops. The data obtained from the scanline method can be applied to the evaluation of stress field in rock mass.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.5 no.3
• /
• pp.49-59
• /
• 1985

Formulation of the geometric optimization for truss structures based on the elasticity theory turn out to be the nonlinear programming problem which has to deal with the Cross sectional area of the member and the coordinates of its nodes simultaneously. A few techniques have been proposed and adopted for the analysis of this nonlinear programming problem for the time being. These techniques, however, bear some limitations on truss shapes loading conditions and design criteria for the practical application to real structures. A generalized algorithm for the geometric optimization of the truss structures which can eliminate the above mentioned limitations, is developed in this study. The algorithm developed utilizes the two-phases technique. In the first phase, the cross sectional area of the truss member is optimized by transforming the nonlinear problem into SUMT, and solving SUMT utilizing the modified Newton-Raphson method. In the second phase, the geometric shape is optimized utilizing the unidirctional search technique of the Rosenbrock method which make it possible to minimize only the objective function. The algorithm developed in this study is numerically tested for several truss structures with various shapes, loading conditions and design criteria, and compared with the results of the other algorithms to examme its applicability and stability. The numerical comparisons show that the two-phases algorithm developed in this study is safely applicable to any design criteria, and the convergency rate is very fast and stable compared with other iteration methods for the geometric optimization of truss structures.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.19 no.1
• /
• pp.52-59
• /
• 1986

As one of trials to process instant sardine foods which can be preserved at room temperature, three kinds of products were prepared as seasoned-dried product (control, C), liquid smoked seasoned-dried product(S) and antioxidant treated seasoned-dried product(E), and their processing conditions and quality stability during storage were examined. Raw sardines were dressed, steamed and then filleted. The sardine fillets were seasoned with the mixed seasoning solution containing $28.0\%$ of sorbitol, $14.0%$ of sugar, $5.6\%$ of table salt, $1.8\%$ of monosodium glutamate, $0.6\%$ of garlic powder and $50.0\%$ of water at $5^{\circ}C$ for 15 hours, and dipped for 45 seconds in $10\%$ Smoke-EZ solution. After liquid smoking, the seasoned and liquid smoked sardine fillets were dried at $45^{\circ}C$ for 4 hours, vacuum packed in laminated plastic film bag(polyester/casted polypropylene= $12{\mu}m/70{\mu}m,\;15{\times}16cm$), and finally pasteurized in water at $95^{\circ}C$ for 30 minutes. The results obtained from chemical and microbial experiments during storage are as follows : the moisture contents, water activity and pH of the products showed little change, and VBN of them slightly increased during storage. The TBA value and POV of the products (E, S) were lower than those of control product(C) considerably. In color values, L value (linghtness) decreased while a and b value (red and yellow) revealed a tendency to increase during storage. The fatty acid composition of the products were similar to those of raw sardine, the predominant fatty acids were 16:0, 20:5, 18:1 and 22:6. The products (E, S) have a good preservative effect on highly unsturated fatty acids during storage. Viable cell counts of those products were negative and histamine contents were less than 2.0 mg/100 g. Among the texture profiles, hardness, elasticity and cohesiveness of the products slightly decreased during storage. Judging from the sensory evaluations, liquid smoked seasoned-dried product(S) was the most desirable, and the products could be preserved in good condition for 40 days at $25{\pm}3^{\circ}C$.

• The Korean Journal of Food And Nutrition
• /
• v.14 no.1
• /
• pp.34-39
• /
• 2001

The purpose of this study was to examine physical properties of the addition of green tea powder on bread flour and dough rheology of white pan bread. Three levels(0.1, 0.5 and 1.0% ) of each green tea powder with bread flour were tested for their effects in dough mixing using rapid disco analyzer, alveogram and farinogram. Addition of green tea powder tended to reduce initial pasting temperature and increase peak viscosity, break down and set back. L(extensibility) and G(swelling index) value in alveogram showed decrement with increasing green tea powder. These meant that the volume of white pan bread would show same tendency. The use of green tea powder increased consistency and water absorption of the bread flour but decreased development time, salability and degree of softening on farinogram. White pan bread with green tea powder had higher value of hardness and springness than without it. Sensory evaluation determined that the white pan bread with 0.5% green tea powder had the highest score.

• Tuberculosis and Respiratory Diseases
• /
• v.63 no.5
• /
• pp.423-429
• /
• 2007

Background: Alveolar recruitment (RM) is one of the primary goals of respiratory care for an acute lung injury (ALI) and acute respiratory distress syndrome (ARDS). The purposes of alveolar recruitment are an improvement in pulmonary gas exchange and the protection of atelectrauma. This study examined the effect and safety of the alveolar RM using pressure control ventilation (PCV) in early ALI and ARDS patients. Methods: Sixteen patients with early ALI and ARDS who underwent alveolar RM using PCV were enrolled in this study. The patients data were recorded at the baseline, and 20 minutes, and 60 minutes after alveolar RM, and on the next day after the maneuver. Alveolar RM was performed with an inspiratory pressure of $30cmH_2O$ and a PEEP of $20cmH_2O$ in a 2-minute PCV mode. The venous $O_2$ saturation, central venous pressure, blood pressure, pulse rate, $PaO_2/FiO_2$ ratio, PEEP, and chest X-ray findings were obtained before and after alveolar RM. Results: Of the 16 patients, 3 had extra-pulmonary ALI/ARDS and the remaining 13 had pulmonary ALI/ARDS. The mean PEEP was 11.3 mmHg, and the mean $PaO_2/FiO_2$ ratio was 130.3 before RM. The $PaO_2/FiO_2$ ratio increased by 45% after alveolar RM. The $PaO_2/FiO_2$ ratio reached a peak 60 minutes after alveolar RM. The Pa$CO_2$ increased by 51.9 mmHg after alveolar RM. The mean blood pressure was not affected by alveolar RM. There were no complications due to pressure injuries such as a pneumothorax, pneumomediastinum, and subcutaneous emphysema. Conclusion: In this study, alveolar RM using PCV improved the level of oxygenation in patients with an acute lung injury and acute respiratory distress syndrome. Moreover, there were no significant complications due to hemodynamic changes and pressure injuries. Therefore, alveolar RM using PCV can be applied easily and safely in clinical practice with lung protective strategy in early ALI and ARDS patients.

• Journal of Korean Ophthalmic Optics Society
• /
• v.7 no.2
• /
• pp.181-187
• /
• 2002

Curvature of Crystalline lens changes by Accommdation's change. When Accommdation gives force vertically to Crystalline lens that is elastic body, length increases for vertex direction. Density distribution and form of Crystalline lens that receive force lean to posterior surface, horizontal force of anterior surface direction is bigger more than horizontal force of posterior surface direction. But, if Accommdation begins to grow more than threshold value, expansity reaches in limit on anterior surface. This time, horizontal force of posterior surface direction is great mored more than horizontal force of anterior surface direction, thickness of posterior surface direction increases because is more than anterior surface direction. Anterior and posterior relationship thickness change difference accomplish the 2-nd funtional line(${\Delta}=B_1D+B_2D^2$) about Accommdation. Thickness (${\Delta}t_a$, ${\Delta}t_p$) difference change curved line of anterior pole-border and border-posterior pole by Accommdation is expressed as following. $${\Delta}t_a=t_a-t_{ao}=t_{max}+t_0{\exp}(-A/B)-t_{ao}$$ $${\Delta}t_p=t_p-t_{po}=t_{min}+t_0{\exp}(A/B)-t_{po}$$ The Parameter value that save in human's Crystalline lens obtain $t_{min}=1.1.06$, $t_0=-0.33$, B=9.32 in anterior, and $t_{max}=1.97$, $t_0=0.10$, B=7.96 etc. in posterior. Vertex curvature radius' change is as following Crystalline lens' anterior and posterior by Accommation $$R=R_0+R_1{\exp}(D/k)$$ The Parameter value that save in human's Crystalline lens obtain $R_{min}=5.55$, $R_1=6.87$, k=4.65 in anterior, and $R_{max}=-68.6$, $R_1=76.7$, k=308.5 in posterior, respectively.

• Composites Research
• /
• v.15 no.4
• /
• pp.23-31
• /
• 2002

The two dimensional size effect of specimen gauge section ($length{\;}{\times}{\;}width$) was investigated on the compressive behavior of a T300/924 $\textrm{[}45/-45/0/90\textrm{]}_{3s}$, carbon fiber-epoxy laminate. A modified ICSTM compression test fixture was used together with an anti-buckling device to test 3mm thick specimens with a $30mm{\;}{\times}{\;}30mm,{\;}50mm{\;}{\times}{\;}50mm,{\;}70mm{\;}{\times}{\;}70mm{\;}and{\;}90mm{\;}{\times}{\;}90mm$ gauge length by width section. In all cases failure was sudden and occurred mainly within the gauge length. Post failure examination suggests that $0^{\circ}$ fiber microbuckling is the critical damage mechanism that causes final failure. This is the matrix dominated failure mode and its triggering depends very much on initial fiber waviness. It is suggested that manufacturing process and quality may play a significant role in determining the compressive strength. When the anti-buckling device was used on specimens, it was showed that the compressive strength with the device was slightly greater than that without the device due to surface friction between the specimen and the device by pretoque in bolts of the device. In the analysis result on influence of the anti-buckling device using the finite element method, it was found that the compressive strength with the anti-buckling device by loaded bolts was about 7% higher than actual compressive strength. Additionally, compressive tests on specimen with an open hole were performed. The local stress concentration arising from the hole dominates the strength of the laminate rather than the stresses in the bulk of the material. It is observed that the remote failure stress decreases with increasing hole size and specimen width but is generally well above the value one might predict from the elastic stress concentration factor. This suggests that the material is not ideally brittle and some stress relief occurs around the hole. X-ray radiography reveals that damage in the form of fiber microbuckling and delamination initiates at the edge of the hole at approximately 80% of the failure load and extends stably under increasing load before becoming unstable at a critical length of 2-3mm (depends on specimen geometry). This damage growth and failure are analysed by a linear cohesive zone model. Using the independently measured laminate parameters of unnotched compressive strength and in-plane fracture toughness the model predicts successfully the notched strength as a function of hole size and width.

• Economic and Environmental Geology
• /
• v.51 no.2
• /
• pp.185-201
• /
• 2018

Nuclear power plants(NPP) are constructed and operated to ensure safety against natural disasters and man-made disasters in all processes including site selection, site survey, design, construction, and operation. This paper will introduce a series of efforts conducted in Korea Hydro and Nuclear Power Co. Ltd., to assure the safety of nuclear power plant against earthquakes and other natural hazards. In particular, the present status of the earthquake, fault, and slope safety monitoring system for nuclear power plants is introduced. A earthquake observatory network for the NPP sites has been built up for nuclear safety and providing adequate seismic design standards for NPP sites by monitoring seismicity in and around NPPs since 1999. The Eupcheon Fault Monitoring System, composed of a strainmeter, seismometer, creepmeter, Global Positioning System, and groundwater meter, was installed to assess the safety of the Wolsung Nuclear Power Plant against earthquakes by monitoring the short- and long-term behavioral characteristics of the Eupcheon fault. Through the analysis of measured data, it was verified that the Eupcheon fault is a relatively stable fault that is not affected by earthquakes occurring around the southeastern part of the Korean peninsula. In addition, it was confirmed that the fault monitoring system could be very useful for seismic safety analysis and earthquake prediction study on the fault. K-SLOPE System for systematic slope monitoring was successfully developed for monitoring of the slope at nuclear power plants. Several kinds of monitoring devices including an inclinometer, tiltmeter, tension-wire, and precipitation gauge were installed on the NPP slope. A macro deformation analysis using terrestrial LiDAR (Light Detection And Ranging) was performed for overall slope deformation evaluation.

• Economic and Environmental Geology
• /
• v.53 no.1
• /
• pp.33-43
• /
• 2020

CO₂ geological storage is currently considered as the most stable and effective technology for greenhouse gas reduction. The saline formations for CO₂ geological storage are generally located at a depth of more than 800 m where CO₂ can be stored in a supercritical state, and an extensive impermeable cap rock that prevents CO₂ leakage to the surface should be distributed above the saline formations. Trough analysis of seismic and well data, we identified the basalt flow structure for potential CO₂ storage where saline formation is overlain by basalt cap rock around PZ-1 exploration well in the Southern Continental Shelf of Korea. To evaluate CO₂ storage capacity of the saline formation, total porosity and CO₂ density are calculated based on well logging data of PZ-1 well. We constructed a 3D geological grid model with a certain size in the x, y and z axis directions for volume estimates of the saline formation, and performed a property modeling to assign total porosity to the geological grid. The estimated average CO₂ geological storage capacity evaluated by the U.S. DOE method for the saline formation covered by the basalt cap rock is 84.17 Mt of CO₂(ranges from 42.07 to 143.79 Mt of CO₂).