• Journal of Advanced Navigation Technology
• /
• v.25 no.5
• /
• pp.363-369
• /
• 2021

In this paper, We propose variable cut-off frequency and variable sample rate small-area multi-channel digital filter for telemetry system. Proposed digital filter reduced hardware area by implementing filter banks that can variably use cut-off frequency and sample rate without additional filter banks for an arbitrary cut ratio. In addition, We propose the architecture in which sample rate can variably be selected according to the number of filters that pass through the multiplexer control. By using time division multiplexing (TDM) supported by the finite impulse response (FIR) intellectual property (IP) of Quartus, the proposed digital filter can greatly reduce digital signal processing (DSP) blocks from 80 to 1 compared without TDM. Proposed digital filter calculated order and coefficients using Kaiser window function in Matlab, and implemented using very high speed integrated circuits hardware descryption language (VHDL). After applying to the telemetry system, we confirmed that the proposed digital filter was operating through the experimental results in the test environment.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.92-97
• /
• 2011

Vehicle lightings are very important for safe driving during night time. Since the eye recovery time after an exposure to oncoming headlights would take after several seconds, the aiming point of vehicle head lamps have to pass safety requirements. Despite the fact that vehicle inclination is variable with vehicle load conditions, the head lamps aiming point is usually fixed at a constant position which is set by car manufacturer. Consequently, vehicle head lamps under varying load conditions often make people in the opposing vehicle uncomfortable, and even worse, can cause an accident. This paper presents an active vehicle lighting mechanism to automatically adjust its aiming point, or cut-off line, in order to compensate the change in vehicle inclination resulting from load variations. The effectiveness of the proposed method is demonstrated through a set of simulations and experiments with a real vehicle.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.117-123
• /
• 2005

The cutoff frequency of a LC output filter for Dynamic Voltage Restorers (DVR) limits the control bandwidth of a DVR system while it attenuates the inverter switching ripples. For a selected cutoff frequency of a LC output filter, infinite number of L-C combinations is possible. Although different L-C combination has different filter characteristics, the filter design on L-C combination has been depended on field experiences without clear analysis. This paper proposes a design criterion and design examples for the L-C filter combination considering the control characteristics and the size of DVRs. An experimental DVR system based on the proposed LC output filter design methodology is built and tested.

• Cartoon and Animation Studies
• /
• s.16
• /
• pp.211-221
• /
• 2009

are cartoon-expressions called cartoon itself to show the characteristic and limit of the presentation system, cartoon, by constitution. These followings are typical examples. First, a character regarded as a cartoonist shows up in the cartoon and constitutes the readers' recognition of the cartoon by himself or herself. Second, the line dividing two cuts is transformed or destroyed and likened to another thing so that can help the readers understand the cuts are physical existence. Most of the approaches to cartoon criticism studies which have been done before are external analyses focused on how to use cuts, balloons, and the two-dimensional expression meaning the relationship between script and picture. The purpose of this research is understanding meta-expressions in online and offline cartoons based on these outcomes. The research on meta-expressions of cartoon is considered to help understanding about the structure of Webcomics and the expansion of expression field in media by examining the expressions of the genre called cartoon.

• KIISE Transactions on Computing Practices
• /
• v.23 no.2
• /
• pp.110-115
• /
• 2017

We propose a new indoor positioning algorithm named Cut-off algorithm. This algorithm cuts off candidates of beacons and reference points in advance, before looking for K neighbor reference points which are guessed to be closest to the user's actual location. The algorithm consists of two phases: off-line phase, and on-line phase. In the off-line phase, RSSI and UUID data from beacons are gathered at reference points placed in the indoor environment, and construct a fingerprint map of the data. In the on-line phase, the map is reduced to a smaller one according to the RSSI data of beacons received from the user's device. The nearest K reference points are selected using the reduced map, which are used for estimating user's location. In both phases, relative ranks of the peak signals received from each beacon are used, which smoothen the fluctuations of the signals. The algorithm is shown to be more efficient in terms of accuracy and estimating time.

• Korean Chemical Engineering Research
• /
• v.57 no.2
• /
• pp.239-243
• /
• 2019

In this study, anthraquinone-2,7-disulfonic acid (2,7-AQDS) is used as negative active material and Tiron is used as positive active material for aqueous redox flow battery (RFB). In previous results that used the 2,7-AQDS and Tiron, sulfuric acid ($H_2SO_4$) was a supporting electrolyte. However, in this study, ammonium chloride ($NH_4Cl$) is suggested as the electrolyte for the first time. By changing the supporting electrolyte from $H_2SO_4$ to $NH_4Cl$, the cell voltage of RFB is improved from 0.76 V to 1.01 V. To investigate the effect of $NH_4Cl$ supporting electrolyte of the performance of RFB, the full-cell tests of RFB using 2,7-AQDS and Tiron that are dissolved in $NH_4Cl$ supporting electrolyte are carried out, while cut-off voltage range is a main parameter to determine their performance. When the cut-off voltage range is 0.2~1.6 V, the hydrogen evolution occurs during charging step. To address the side reaction effect, the cut-off voltage range is changed to 0.2~1.2 V. When the revised cut-off voltage range is used and the current density of $40mA/cm^2$ is applied, hydrogen evolution is not observed and the optimal RFB shows the charge efficiency of 99% and discharge capacity of 3.3 Ah/L at 10cycle.

• The Journal of the Acoustical Society of Korea
• /
• v.33 no.1
• /
• pp.40-47
• /
• 2014

Interaction between the unsteady flow emitted from the blade of the centrifugal fan and the volute tongue region of fan duct is known as the main noise source of the centrifugal fan. In this paper, the relative contributions of the volute tongue region of the centrifugal fan is analyzed to utilize as the foundation data of low noise design. The internal hybrid CAA (Computational Aero-Acoustics) method is used to predict noise radiated from the main noise source. This method is the noise prediction technique using CFD (Computational Fluid Dynamics), Acoustic analogy, and BEM(Boundary Element Method). The relative contributions of the centrifugal fan volute tongue region using the hybrid CAA method show that the region between the cut-off and the scroll has high contribution than the region between the cut-off and the outlet and the hub region of blade has high contribution than the shroud region of blade. These results is utilized as the important data for the development of low noise centrifugal fan.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.626-626
• /
• 2013

P-N 접합에 의해 절연된 게이트를 통해 전류 통로를 제어하는 접합형 전계효과 트랜지스터(Junction Field Effect Transistors; JFETs)는, 입력 임피던스가 크고, 온도에 덜 민감하며, 제조가 간편하여 집적회로(IC) 제조가 용이하고, 동작의 해석이 단순하다는 장점을 가지고 있다. 특히 JFET는 선형적인 전류의 증폭 특성을 가지고 있으며, 잡음이작기 때문에, 감도가 우수한 음향 센서의 증폭회로, 선형성이 우수한 증폭회로, 입력 계측 증폭 회로 등에 주로 사용되고 있다. 기존에 사용되는 JFET 소자는 구조와 제조 공정에 따라서, 컷 오프 전압($V_{cut-off}$)과 드레인-소스 포화 전류($I_{DSS}$)의 변화가 심하게 발생하여, 소자의 전기적 특성 제어가 어렵고, 소자의 수율이 낮다는 문제점이 있다. 본 연구에서는 TCAD 시뮬레이션을 통해 게이트 전압에 의해 채널이 형성되는 채널 층의 상하부에 각각 $Si_xGe_{1-x}$로 이루어진 상부 및 하부 확산 저지층을 삽입한 JFET 소자 형성하여, 게이트 접합부의 접합 영역 확산을 저지하고, 상기 게이트 접합부가 계면에서 날카로운 농도 구배를 갖도록 함으로써, 공정 변화에 따른 전기적 특성의 편차가 작아지는 JFET 소자 구조를 만들어 전기적 특성을 개선하였다. JFET은 채널층에 삽입된 $Si_xGe_{1-x}$ 층의 두께, Ge 함유량 및 n채널층의 두께를 변화하였을 때, off 상태의 게이트-소스 전압이 감소한 반면에 드레인-소스 포화 전류($I_{DSS}$)와 컨덕턴스(gm) 값이 증가하였다. 삽입된 $Si_xGe_{1-x}$층이 Boron이 밖으로 확산되는 현상이 감소하여 채널이 좁아지는 현상을 막아 소자의 전기적 특성을 개선함으로써 제조공정의 변화에 관계없이 컷오프 전압을 정확하고 안정되게 제어할 수 있고 이를 통해 소자의 수율을 높일 수 있을 것으로 기대된다.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.1C
• /
• pp.65-73
• /
• 2006

The purpose of this study is to design and analyze the pre-modulation filter with the variable -3dB cutoff frequency and linear phase response for bandlimiting the allocation of radio frequency bandwidth in PCM/FM transmission system. For the implementation of this required filter, the digital FIR filter, DAC and variable 2nd order LPF have been constructed with the filter block which designed and analyzed by each stage in order to satisfy the attenuation characteristic requirement of the analog 7th order bessel filter. The paper also concerned the linear phase properties for the filter block. Especially we have carried out the linear phase simulation with real parts for variable 2nd order LPF and compared this simulation results with the one of the fixed bandwidth 2nd order bessel filter for validating the linear phase requirement.

• Journal of Advanced Navigation Technology
• /
• v.24 no.1
• /
• pp.53-60
• /
• 2020

In this paper, We have studied the structure of a Telemetry Transmitter capable of transmitting variable data rates. This paper proposed a structure combining variable pre-modulation filter with cutoff characteristic with variable input sample rate converter. Variable pre-modulation filter has the same characteristics as pre-modulation filter and is converted to a constant sampling rate without structural changes according to the variable input data rate. We propose a software program that actively controls variable pre-modulation filter and variable input sample rate converter to respond to real-time changing data.