• Journal of the Korean Vacuum Society
• /
• v.15 no.1
• /
• pp.24-30
• /
• 2006

Integrated cavity output spectroscopy(ICOS) is a simple, non-intrusive absorption measurement technique that can detect and quantify trace-level gas species. The spectral absorbance of a gas is quantified from the integrated optical output of the modulated high-finesse cavity containing the sample which is irradiated by a wavelength-swept laser source. We constructed an experimental setup by using a tunable single mode external cavity diode laser operating at the wavelength near 765 nm and a Fabry-Perot cavity with length modulation achieved by a piezoelectric transducer where one of the cavity mirrors sat on. In the experiment performed on minute oxygen gas at the wave-length near 764.5nm, we demonstrated the minimum detectable absorption of $8.45\times10^{-8}cm^{-1}$.

• Journal of Korean Society of Forest Science
• /
• v.99 no.1
• /
• pp.1-8
• /
• 2010

The optimum forest road density was calculated with the method which is used in Europe on the investigation site in Korea. The economical optimum forest road density at the minimum total transport cost was 10.51 m/ha. The total transport cost was calculated 235,354 won/ha per year. The forest road construction cost amounted to 99,693 won/ha per year in case of the depreciation period of 30 years and the interest rate of 3%, the forest road maintenance cost amounted to 14,502 won/ha per year, the logging cost amounted to 99,564 won/ha per year, the cost of footpaths amounted to 18,142 won/ha per year, the cost by the loss of the production area amounted to 3,454 won/ha per year.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.277-283
• /
• 2020

In a concentric magnetic gear, which replaces the teeth of a mechanical gear with a permanent magnet, the polar ratio of the magnet that determines the reduction ratio affects the behavior of the magnetic gear dramatically. This study analyzed the density of transmission torque, the efficiency of torque considering the solid loss, and the torque quality, including the cogging characteristics using finite element analysis. When the pole number on the driving side was changed from two to five, it was confirmed that there was an optimal pole ratio, in which the transmission torque was maximized. Because eddy current generation density is proportional to the magnetic field, the transmission efficiency also shows a similar tendency to the transmission torque density, and the efficiency is more than 95% at a low gear ratio. The cogging characteristics due to the interaction of the permanent magnets with the limited number of poles are inversely proportional to the least common multiple between the number of magnets on the drive side and the number of modulator teeth. A test model was built for the transmission torque evaluation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.294-295
• /
• 2005

다중 코어를 이용한 대전류 변압기용 Mn-Zn ferrite를 제조하고 전자기적 특성을 분석하였으며, 제조된 자심재료를 이용하여 변압기를 제조하고 전원장치에 탑재하여 효율특성을 분석하였다. ZnO의 몰비가 증가할수록 혼합 스피넬의 형성을 통한 보아 자자의 증가로 인해 투자율은 증가하고 상대적으로 전력손실이 감소하여 $Fe_2O_3$ : MnO : ZnO = 53 : 36 : 11 mo\% 일 때 가장 우수한 특성을 나타냈고, 열처리 공정의 승온 과정에서부터 산소 분압을 제어하고 최적의 대기압 상수를 산출함으로써 Zn-loss 현상을 최소화하여 ZnO 11 mol%, 대기압 상수 7.7일 때 투자율 2350, 밀도 4.9 $g/cm^3$, 비저항 480 ${\Omega}cm$, 300 mT의 최대 자속 밀도 특성을 갖는 우수한 자심 재료를 개발하였다. 그리고 최소 손실 온도를 $90^{\circ}C$ 이하로 감소시켰으며 100 kHz에서 250 $kW/m^3$의 낮은 전력손실을 나타냈다. 또한 개발된 자심재료를 이용하여 제조된 전원장치는 30~80A의 출력 전류에서 85% 이상의 고효율을 얻었다.

• Journal of Advanced Navigation Technology
• /
• v.22 no.2
• /
• pp.64-69
• /
• 2018

Automatic test equipment for field maintenance of aircraft mounted equipment is effective for integrated design when operating a small number of aircraft for special purposes. The integrated automatic test equipment identifies commonly used interfaces and is used for branching or generating routes for each unit under test specific inspection. High-precision signals such as RTD, TC, and analog voltage can cause measurement errors due to conduction resistance during signal branching and connection when generating branches and paths. The measurement error caused by the resistance of the wire leads to a lot of restrictions in designing the equipment to be inspected. In this paper, we propose a method of calibrating highly accurate signals of an integrated automatic inspection equipment that minimizes measurement errors of analog voltage and high - precision signals.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.5
• /
• pp.767-774
• /
• 2022

In this paper raw spectrum data were analyzed to suggest the moving forward of performance evaluation and quality control of wind profilers of four manufacturers operating in South Korea. For the analysis, the profile of the spectrum averaged by season and the profile of four statistical values (minimum, average, median, and maximum) calculated by Power Spectrum Density (PSD) were used. The quality of spectrum data was the best for LAP-3000, followed by YKJ3, PCL-1300, and CLC-11-H. In Cheorwon and Chupungnyeong, where PCL-1300 was installed, the variability of the spectrum due to ground clutter and non-meteorological signals was large, so ground clutter removal and signal processing such as moving average and multi-peak were required. In Gunsan and Paju, where CLC-11-H was installed, DC (Direct Current) bias and propagation folding were found, so it is necessary to remove the DC bias and limit the effective altitude for observation.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.8 no.2
• /
• pp.10-20
• /
• 2005

The change of stream creation has a very sensitive effect on runoff analysis model using the divergence characteristic of stream. Therefore, in this study, the threshold area of stream creation was examined the change characteristic of topographical parameters. The subject basin of the research was the upper basin of the Kumho water gage station which is located in the middle of the Kumho river. The 1:25,000 numerical geography which was constructed $10{\times}10m$ mesh was used. The range of investigation of topographical parameters are number of stream order, length, area, slope, basin relief, sinuosity ratio, drainage density and total stream length etc. It was found from the result of analysis that the threshold value of 1st order stream has a very big effect on topographical parameters of basin. It was found that the threshold area of stream creation was under $0.10km^2$, the parameters showed a big change but showed a very small change over $0.10km^2$.

• Journal of the Korean Wood Science and Technology
• /
• v.41 no.1
• /
• pp.42-50
• /
• 2013

Since 1990's, a plywood for flooring base has gotten customers' demand. Costs of raw material and production increased because of changed environment of industry. Tropical timber such as Red Meranti (Shorea acuminate) used for raw material of the floor has been depleting beside countries in South Eastern Asia changed species of afforestation. As a result, it gets hard to secure good quality of raw material for plywood. Moreover plywood price is increased suddenly after earthquake in Japan. Eucalyptus (Eucalyptus globulus) in china has been using for raw material as a countermeasure of changed environment of industry. In this study, possibility of using flooring consisted of Eucalyptus veneer as crossband layers was checked by deflection experiments. Flooring consisted of Red Meranti was used for comparison. Two factors which impact on deflection are a type of density gradient and density difference between Long-grain veneer and Short-grain veneer. Red Meranti samples are M type of density gradient on the other hand Eucalyptus samples are W type of density gradient. The more samples have high density difference, the more deformation was checked. A sample which has big density difference between core and cross bands layer warp more also deform. Flooring was deformed smaller than plywood and samples which have big density difference was deformed more.

• Journal of the Korean Applied Science and Technology
• /
• v.37 no.3
• /
• pp.516-525
• /
• 2020

The densities of aqueous solutions of the amphiphile 2-(2-hexyloxyethoxy)ethanol (C₆E₂) were measured at 279.15 K and 282.15 K by vibrating-tube densitometry. Then using the density data of the binary C₆E₂ (1)/water(2) system, the excess volumes and partial molar volumes were determined at various compositions. Excess volume V^E exhibits negative deviation for the whole region of composition, which implies relatively stronger attraction between molecules. At the C₆E₂ mole fraction of around 0.45, V^E was at its minimum. Partial molar volume ${\bar{V}}_1$ increases monotonously with the mole fraction x₁(=x) and ${\bar{V}}_2$ decreases with x. Any particular point in ${\bar{V}}_1$ and ${\bar{V}}_2$, which may point to molecular association, was unobserved.

• Journal of the Korean Vacuum Society
• /
• v.14 no.4
• /
• pp.258-262
• /
• 2005

We report on the field emission properties from vertically aligned carbon nanotubes (CNTs) produced by a triode PECVD with a SiNx capping layer on metal catalyst. It is found that the CNTs density can be controlled by the capping layer thickness and decreases with increasing SiNx thickness. The CNT density of $\~$ 104/$cm^{2}$ exhibited highest electron emission characteristics, the threshold field of 1.2 V/$\mu$m and the current density of 0.17 mA/$cm^{2}$ at 3.6 V/$\mu$m. We have carried out investigation of electron emission stability under ambient gas of N2. The electron emission stability was improved with decreasing CNT density. Under $1\times$$10^{-5}$ Torr ambient pressure, the CNTs in 5 $\mu$m hole show electron emission current higher than $1\times$$10^{-4}$ A/cm2 and it's electron emission uniformity has $2\%$.