• Journal of Advanced Navigation Technology
• /
• v.20 no.6
• /
• pp.574-579
• /
• 2016

Unlike general unmanned aerial vehicles, the quad-rotor is attracting the attention of many people because of simple structure and very useful value. However, as the interest in drones increases, the safety and location of vehicles are becoming more important provide against aviation safety accidents or lost accidents. Therefore, in this paper, we propose a tracking system that stabilizes the model with a simple controller by linearized modeling and grasp tilt angle data from various sensor through the filter. The developed tracking system transmits the position of the quad-rotor in flight to the computer and shows it through the route, so it can check the flight path and various information such as flight speed and altitude at the same time. Then the sensor used in the actual quad-rotor can not measure exact sensor data for disturbance and vibration. So we use sensor fusion of Kalman filter and Complementary filter to overcome this problem and the stability of the quad-rotor hovering is realized by PID control. Through simulation, various information such as the speed, position, and altitude of the quad-rotor were confirmed in real time.

• Journal of the Korean Society for Railway
• /
• v.17 no.1
• /
• pp.19-27
• /
• 2014

Urban railway vehicles operate in downtown areas. Due to increases in the number of passengers and changes in the service plans, railway vehicles are expected to operate on sharp curved tracks. However, on these tracks, the running stability of the railway vehicles is significantly decreased and the creepage is increased. Creepage causes the wheel/rail to wear and vibration. Therefore, reducing the creepage helps ensure the running stability and can be beneficial for the environment and cost. In this paper, the longitudinal creepage is analyzed using a railway vehicle model on a sharp curved track. Furthermore, in order to minimize the problems when a railway vehicle runs on a sharp curved track, the characteristics of a bogie are optimized using response optimization.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.3
• /
• pp.241-249
• /
• 2004

There is an over head hoist transporter(OHT) by the system for delivering the wafer in semiconductor processing. The transfer system consist of carrier, vehicle, rail and support. The Tail supporting the wafer and the transfer system should maintain enough strength and stiffness. To achieve lightness and enough strength and stiffness, optimization algorithm should be introduced in design process. In this study, two kinds of section shapes as L-type, C-type is carried out the structure analysis and optimization. Total weight of rail is to be minimized while displacement should not exceed limit. To improve the initial model, topology optimization is done by the plain problem. Size optimization is done with 3D solid element and PLBA algorithm, the RQP algorithm. The weight of optimum model as L-type, C-type is decreased by 2.3%, 10% respectively. It is improved better than the initial model in the strength and stiffness of the structure.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.42 no.4
• /
• pp.41-46
• /
• 2005

Acoustic problems in the environment have gained attention due to the noise and vibration contact often in industry as well as life on modem society. Noise is one of safety element in industry, this proves damaging to humans from both a physical and a psychological aspect and so drop working efficiency. Various noises are happened from machines of manufacturing process in PCB industry. This paper present a new approach for subband feedback Active Noise Control (ANC) using Mel scale for headset system in PCB industry. The proposed Mel scale subband algorithm had a performance advantage over the subband algorithm in the noise attenuation and convergence time.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.36 no.8
• /
• pp.905-911
• /
• 2012

To establish a floating offshore wind turbine simulation model, a tension leg platform is added to an onshore wind turbine. The wind load is calculated by using meteorological administration data and a power law that defines the wind velocity according to the height from the sea surface. The wind load is applied to the blade and wind tower at a regular distance. The relative Morison equation is employed to generate the wave load. The rated rotor speed (18 rpm) is applied to the hub as a motion. The dynamic behavior of a 2-MW floating offshore wind turbine subjected to the wave excitation and wind load is analyzed. The flexible effects of the wind tower and the blade are analyzed. The flexible model of the wind tower and blade is established to examine the natural frequency of the TLP-type offshore wind turbine. To study the effect of the flexible tower and blade on the floating offshore wind turbine, we modeled the flexible tower model and flexible tower-blade model and compared it with a rigid model.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.2 s.46
• /
• pp.325-331
• /
• 2007

This paper proposed modelling and design method in suspension system design to analyze active suspension equipment by adopting active robust control theory. Recent in the field of suspension system design it is general to adopt active control scheme for stiffness and damping, and connection with other vehicle stability control equipment is also intricate, it is required for control system scheme to design more robust, higher response and precision control equipment. It is known that active suspension system is better than passive spring-damper system in designing suspension equipment. We analyze suspension system with considering location of front-rear wheel and driving velocity, then design control system. Numerical example is shown for validity of robust control system design in active suspension system.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.136-136
• /
• 2011

AlSb는 광전자 소자응용에 매우 유용한 재료이며 이를 이용한 반도체소자 설계 및 밴드갭 엔지니어링을 위해서는 화합물 반도체의 전자밴드구조를 포함한 광학적 특성이 반드시 요구된다. 본 연구는 이러한 요구의 해결방안으로서 AlSb 화합물의 유전함수 온도의존성을 0.7~5.0 eV의 에너지 영역에서 타원편광분석법을 이용하여 분석하였다. AlSb는 산소와 급격히 반응하기 때문에, 대기 중에서 물질 고유의 광특성이 유지되기 어려울 뿐만 아니라, 박막 위에 생성되는 산화막 때문에 순수한 AlSb의 유전함수 측정이 불가능하다. 따라서 박막의 산화 효과를 최소화하기 위하여 초고진공 상태의 molecular beam epitaxy 챔버 안에서 800 K의 온도로 성장한 1.5 ${\mu}m$ 두께의 AlSb 박막을 상온 300 K 까지 온도를 단계적으로 변화시켜가며 타원편광분석기를 이용하여 실시간으로 측정하였다. 각 온도에서 측정된 AlSb의 유전함수를 2차 미분하여 전이점(critical point)을 분석한 결과 $E_0$, $E_0+{\Delta}_0$, $E_1$, $E_1+{\Delta}_1$, $E_0'$, $E_0'+{\Delta}_0'$, $E_2$, $E_2+{\Delta}_2$에 해당하는 각 전이점들의 온도 의존성을 확인할 수 있었다. 실험에서 측정된 특정 온도를 포함하여 임의의 온도에서의 AlSb의 유전함수를 유도하기 위하여 변수화모델을 사용하였고 이를 통하여 각 변수들의 온도 의존 궤적을 분석하였다. 2차 미분법을 이용한 전이점들의 온도의존성 분석결과를 기준으로 변수화 모델링을 진행하였으며 그 결과 각 온도에서 실제 유전함수와 근소한 차이를 갖는 AlSb의 유전함수 모델을 만들 수 있었다. 따라서 본 연구결과는 반도체 물성에 대한 학술적 측면뿐 아니라 고온에서의 소자공정 실시간 모니터링 및 반도체 소자 설계 등의 산업적 측면에서 매우 유용하게 사용될 것으로 기대된다.

• Journal of the Society of Disaster Information
• /
• v.7 no.4
• /
• pp.259-265
• /
• 2011

After the commercial opening of the KTX in 2005, the high speed railroad has been rapidly emerged as the major transportation means due to its high energy efficiency. Recently, the government has announced its plan to build the future transportation system around the high speed railroad. Based on this policy, the existing lines as well as the lines under construction or design are planning to increase design speed. In this paper, the suitability of the mid-span PSC girder bridges for the high speed railroad is evaluated via dynamic analysis. IT, Precom, and WPC girder bridges are considered for the purpose of this study and, for comparison, the identical modeling method and the analysis technique are utilized. The performance indices used for dynamic performance evaluation are the natural frequency, the vertical displacement, the end axial displacement, track irregularity, etc. The KTX train is utilized as a dynamic load, and the dynamic analysis is performed up to the train speed of 420km/hr with the increment of 10km/hr.

• Journal of the Korean GEO-environmental Society
• /
• v.15 no.3
• /
• pp.41-48
• /
• 2014

Experimental study of sedimentation and self-weight consolidation has been primary research area in dredged soil. However, good quality of the dredged soil and minimum water pollution caused by the pumping of reclaimed soil require intensive study of the flow characteristics of dredged material due to dumping. In this study, continuity and the equilibrium equations for mass flow assuming single phase was derived to simulate mass flow in dredged containment area. To optimize computation and modeling time for three dimensional geometry and boundary conditions, depth integration is applied to governing equations to consider three dimensional topography of the site. Petrov-Galerkin formulation is applied in spatial discretization of governing equations. Generalized trapezoidal rule is used for time integration, and Newton iteration process approximated the solution. DG and CDG technique were used for weighting matrix in discontinuous test function in dredged flow analysis, and numerical stability was evaluated by performed a square slump simulation. A comparative analysis for numerical methods showed that DG method applied to SU / PG formulation gives minimal pseudo oscillation and reliable numerical results.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.2
• /
• pp.114-120
• /
• 1999

The DDAM(Dynamic Design Analysis Method) has been the most popular method for the shock response analysis of naval shipboard equipment. It was common to model the equipment as a simplified mass-spring system with multi degree of freedom in DDAM. Nowadays, however, it is necessary to adopt the finite element method for the shock response analysis due to the complexity of equipment. In this study, the DDAM program is developed to evaluate the performance of shock-resistance of FEM models using MSC/NASTRAN DMAP(Direct Matrix Abstraction Program) which provides the practical tools in interfacing with the externally developed program. Through the numerical test of the structural components and comparison with the results of ANSYS DDAM, it is confirmed that the developed program can be applicable to analyze the shock responses of the shipboard equipments.