• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.1
• /
• pp.13-18
• /
• 2014

Sensor nodes are used for monitoring and collecting the environmental data via wireless sensor network. The wireless sensor network with various sensor nodes draws attention as a key technology in ubiquitous computing. Sensor nodes has very small memory capacity and limited power resource. Thus, it is essential to have energy efficient strategy for the sensor nodes. Since the sensor nodes are operating on the same frequency bands with ISM frequency bands, the interference by the devices operating on the ISM band degrades the quality of communication integrity. In this paper, the convolutional code is proposed instead of ARQ for the error control for the sensor network. The proposed convolutional code was implemented and the BER performance is measured. For the fixed transmitting powers of -19.2 dBm and -25dBm, the BER with various communication distances are measured. The packet loss rate and the retransmission rate are calculated from the measured BER. It is shown that the porposed method obtained about 9~12% and 12-19% reduction in retransmission rate for -19.2 dBm and -25 dBm respectively.

• Journal of Internet Computing and Services
• /
• v.13 no.3
• /
• pp.49-59
• /
• 2012

Throughout developing digital technology, reproduction of image is growing better day by day. And at the same time, diverse image editing softwares are developed to manage images easily. In the process of editing images, those programs could delete or modify EXIF files which have the original image information; therefore images without the origin source are widely spread on the web site after editing. This matter could affect analysis of images due to the distortion of originality. Especially in the court of law, the source of evidence should be expressed clearly; therefore digital image EXIF file without deletion or distortion could not be the objective evidence. In this research, we try to trace the identification of a digital camera in order to solve digital images originality, and also we focus on lens distortion correction algorism which is used in digital image processing. Lens distortion correction uses mapping algorism, and at this moment it also uses interpolation algorism to prevent aliasing artifact and reconstruction artifact. At this point interpolation shows the similar mapping pattern; therefore we want to find out the interpolation evidence. We propose a minimum filter algorism in order to detect interpolation pattern and adjust the same minimum filter coefficient in two areas; one has interpolation and the second has no interpolation. Throughout DFT, we confirm frequency character between each area. Based on this result, we make the final detection map by using differences between two areas. In other words, thereby the area which has the interpolation caused by mapping is adjusted using minimum filter for detection algorism; the second area which has no interpolation tends to different frequency character.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.24 no.1
• /
• pp.92-100
• /
• 2018

Vortical systems are considered a main feature to sustain turbulence in a boundary layer through interaction. Such turbulent structures result in frictional drag and erosion or vibration in engineering applications. Research for controlling turbulent flow has been actively carried out, but in order to show the effect of vortices in a turbulent boundary layer, it is necessary to clarify the mechanism by which turbulent energy is transferred. For this purpose, it is convenient to demonstrate and capture phenomena in a laminar boundary layer. Therefore, in this study, the interactions of disturbed flow around a hemisphere on a flat plate in laminar flow were analyzed. In other words, a street of hairpin vortices was generated following a wake region formed after flow separation occurred over a hemisphere. Necklace vortices surrounding the hemisphere also appeared due to a strong adverse pressure gradient that brought high momentum fluid into the wake region thereby leading to an increase in the frequency of hairpin vortices. To mitigate the effect of these necklace vortices, local suction control was applied through a hole in front of the hemisphere. Flow visualization was recorded to qualitatively determine flow modifications, and hot-film measurements quantitatively supported conclusions on how much the power of the hairpin vortices was reduced by local wall suction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.18 no.1
• /
• pp.425-430
• /
• 2017

RFID is a technology that uses radio frequency to read information in tags attached to objects or people. Because it reads the information without contact when tracking the location using tags in a RFID system, there can be errors between the actual position and measured position. In this paper, three methods (the method of radiation pattern, the method of the median value, and the method using both the radiation pattern and median value) are proposed to identify the location of objects or people using the RFID technique. The location identification system based on RFID was constructed and tags were arranged in a square pattern. The real location and experimentally predicted location of an object containing a reader were compared to confirm the error. Instead of the existing papers that obtained the approximately location of a reader by calculating the center of gravity of all tags read by that reader, in this study, the predicted location was obtained by the median value and the radiation pattern. This study validated which method was the most efficient among the three methods proposed in this paper through the data of the read tags. As a result, the method of the median value had the smallest error among those assessed.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.593-602
• /
• 2020

Power cables installed in domestic factories or underground can cause accidents depending on the manufacturing process, installation, and environmental conditions during use. When an accident occurs in a power cable, it can cause enormous economic loss and social confusion. Hence, the importance of preventive management of the cable through diagnosis is increasing to prevent it. Therefore, in this paper, a diagnostic sample cable was produced by simulating a part that could be a problem due to the installation, manufacturing defects, or deterioration of cables that can occur in the field. Dielectric loss Tangent (tan 𝛿; TD), and Partial Discharge(PD) tests were performed. Partial discharge and AC (60Hz) withstand voltage equipment using High-Frequency Current Transformer (HFCT) were applied After applying a VLF (Very Low Frequency) power supply with a frequency of 0.1Hz was applied. As a result, B and C phase defect samples at a 2.0U₀ voltage through the VLF could measure the internal partial discharge in the A-phase normal sample cable from the noise at a 0.5U₀ to 2.0U₀ voltage. In addition, the 1.5U₀ voltage was measured through the AC (60Hz) withstand voltage equipment of the commercial frequency to verify its effectiveness. Partial discharge in the run-off state was measured at a voltage of 1.0U₀, and there was a risk when installing the equipment. AC power equipment showed a difficulty of movement by volume or weight. The diagnostic method, through the VLF of the quadrant state, revealed its safety and effectiveness.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.7
• /
• pp.607-615
• /
• 2016

This study concerns the transmission of energy and data using induced electromotive force. Due to the requirements of weapon systems, most arms are kept in an armory for a very long time before being used. During this time, the reserve battery, which serves mostly as a power supply for the electronic fuze, can be degraded, thus causing problems when it is actually needed. We attempt to solve the various problems associated with the old fuze system caused by long-term storage by using the 'induction power' transmitted from another device just before its operation, instead of using 'built-in power'. We tried to find the best carrier frequency to communicate with the system by induced electromotive force. Also, we changed the communication method for transmitting the 'induction power' from 'FM/AM modulation' to 'Duty ratio modulation', which can transmit a large amount of data in a short time. Through experiments, it was demonstrated that the induction coil can replace the reserve fuze's battery without any problem, thus confirming the possibility of using an induction coil as the power supply source of the electronic fuze.

• Radiation Oncology Journal
• /
• v.5 no.1
• /
• pp.49-58
• /
• 1987

Hypertermia for the treatment of cancer has been introduced for a long time and the biological effect for the use of hyperthermia to treat malignant tumors has been well established and encouraging clinical results have been obserbed. Unfortunately, however, the engineering or technical aspects of hyperthermia for the deep seated tumors has not been satisfactory. We developed the radiofrequency capactive hyperthermia device (Greenytherm-GY8) in cooperation with Yonsei Cancer Center and Green Cross Medical Corporation. It was composed with $8{\sim}10MHz$ RF generator, capacitive electrode, matching system, cooling system, temperature measuring system and control PC computer. The thermal profile was investigated in agar phantom, animals and in human tumors, heated with capactivie RF device. Deep and homogeneous heating could be achieved in a large phantom of 25cm diameter and 19cm thick when heated with a pair of 23cm diameter electrodes, coupled to both bases of the phantom, when the size of the two electrodes was not the same, the region near the smaller electrode was preferentially heated. It was, therefore, possible to control the depth of heating by choosing proper size of electrodes. Therapeutic temperature $(42^{\circ}C{\sim}43^{\circ}C)$ could be obtained in the living animal experiments. Indications are that deep heating of humn tumors might be achieved with the capacitive method, provided that subcutaenous fat layer is cooled by temperature controlled bolus and large size of electrodes.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.11 no.1 s.53
• /
• pp.89-97
• /
• 2007

Parameters including the seismic sources and the elastic wave propagation characteristics were analysed using the observed ground motions from 12 Fukuoka region earthquakes. The Levenberg-Marquardt algorithm was applied to invert all the variables non-linearly and simultaneously with S wave energy in fiequency domain. Average stress drop of 12 events and local attenuation parameter $\kappa$ under seismic stations were estimated to about 79.2-bar and 0.043 respectively. Regional attenuation parameter, Qo and ${\eta}$, were also estimated to be about 248.1 and 0.558 respectively. Low value of Qo seems to caused by inhomogeneous tectonic characteristics between Japan island and southern Korean peninsula. $\kappa$ values are much higher than that characterizing EUS (Eastern United States) region, and nearly similar to that of WUS (Western Waited States) region. If the informations on site specific amplification of all the seismic stations are known, $\kappa$ values can be estimated more precisely. All the values including the seismic sources and the site and crustal scale propagation characteristics can be used as seismic design parameters.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.14 no.2
• /
• pp.24-29
• /
• 2015

In this paper, a microstrip antenna with isoflux radiation patterns is presented for Low Earth Orbit(LEO) medium-sized satellites. Because of making isoflux patterns, the ground of proposed antenna under the patch was transform into a trapezoid for adjusting fringing field between the patch and ground. Next, the cavity walls were located at end of the ground for reducing back radiation. The proposed antenna was designed to receive S-band uplink(2.025 ~ 2.110 GHz) and the dimensions of the designed antenna with the ground are $160mm{\times}160mm{\times}40mm$ ($1.1{\lambda}{\times}1.1{\lambda}{\times}0.3{\lambda}$, ${\lambda}$ is the free-space wavelength at 2.068 GHz). Measured -10 dB bandwidth was 90 MHz(4.4 %) and it covers the required system bandwidth. Also, measured 3 dB axial ratio was 18 MHz(0.9 %). On the other hand, measured radiation patterns were isoflux patterns and its measured gain was 5.31 dBi at E-plane $46^{\circ}$ in the y-axis pol.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.17 no.5
• /
• pp.143-150
• /
• 2018

With the rapid development of RF based high speed wireless communication technology, devices that can be applied to IoT networks based on RF bandwidth are rapidly spreading, nevertheless, the development speed of the RF communication is not possible to keep up with the spread of the RF band for wireless communication. In this situation, OWC technology that uses visible light source as a transmitter is attracting attention as a technology that can overcome the band exhaustion problem of RF based wireless communication technology. Although, due to the distortion of the LED illumination shape by camera exposure time and LED blinking period, the LED illumination detection rate is degraded and the RoI setting is inaccurate. In this paper, we propose an adaptive median filter applied LED illumination detection algorithm for low rate CamCom, it is possible to detect a clear RoI and LED illumination. This research will be able to play a role as a complementary material of RF based wireless communication technology efficiently.