• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.10-18
• /
• 2006

In this thesis paper the effect that the change in the brightness of headlights has on a driver's perception had been researched. For this research, an indoor laboratory was constructed and designed. Then, a system to measure the reaction braking time of finding obstacle and the subject's brain waves after a moment of change in the headlamp's brightness was constructed. And before the real experiment was began, the trial experiment to decide test time, subject's rest time, detailed experimental steps, the headlamp's patterns of voltage change and an obstacle course was executed.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.68-73
• /
• 2006

As in the measurement of ground resistance by using the 3 point fall-of-potential method, it is known that the distance of current electrode should be at the point of showing the plateu on the potential curve. But the problem is that it my be practically impossible to meet the condition in actual sites. For solving such a situation, this paper provides the least distance of current electrode according to the analysis for the test-field measurement showing that it is feasible to measure the ground resistance in the two in current electrode distance as the length of driven-rod type electrode and the some district length of mesh electrode.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.10
• /
• pp.100-106
• /
• 2006

This paper proposes a full fuzzy-logic-based vector control for a permanent-magnet synchronous motor (PMSM). The high-performance of the proposed fuzzy logic control (FLC)-based PMSM drive are investigated and compared with the conventional proportional-integral (PI) controller at different conditions, such as step change in command speed and load and etc. In the experimental and simulation the FLC is employed in the speed and current controller. The experimental results show to be a suitable replacement of the conventional PI controller for the high-performance drive system.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.73-78
• /
• 2008

A polarimetric fiber-optic CT has been developed by using a sensing coil made of a length of sun fiber. A Faraday rotator mirror is attached to the end of the sensor coil to double the sensitivity and to suppress the residual linear birefringence effect. From the current measurements, the linear error no more than ${\pm}2[%]$ was obtained. The output of spun fiber sensor coil was compared with those of the twisted- and the flint glass fiber's, and it fumed out to almost 50 times, 2 times more sensitive, respectively.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.131-137
• /
• 2009

This presents the equivalent circuit model of solar cell with irradiation and temperature condition. Based on solar cell model, the photovoltaic module specification of manufacturer compare with photovoltaic module simulation and is investigated by simulation results. The obtained results indicate that residual of simulation value and specification value about photovoltaic module is lower. There is considerable validity in simulation of photovoltaic module. Thus, the optimum simulation of photovoltaic module array are studied in this paper. This paper propose the sizing optimization of photovoltaic module array for stand-alone photovoltaic system. Also, the proposed stand-alone photovoltaic system is setting in special region(in seoul). This paper presents simulation characteristic of optimization output power in seoul.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.24 no.5
• /
• pp.16-28
• /
• 2010

This paper proposes maximum torque control of SynRM drive using artificial intelligent(AI)PI and artificial neural network(ANN). The control method is applicable over the entire speed range and considered the limits of the inverter's current and voltage rated value. For each control mode, a condition that determines the optimal axis current for maximum torque operation is derived. The proposed control algorithm is applied to SynRM drive system controlled AIPI and ANN controller and the operating characteristics controlled by maximum torque control are examined in detail.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.154-160
• /
• 2009

This paper shows a basic data of the surface discharge characteristics for epoxy resin in Dry-Air as being focused on environmentally friendly insulating Gas. Used electrodes are needle to plane, sphere to plane and KS M3015 electrodes. With the changing electrodes in same condition, we can obtain different creeping lengths, surface discharge voltages and surface dielectric strengths, respectively. Surface dielectric strengths of Needle to plane electrodes are more higher than the others. Moreover, it is considered that the surface discharge characteristics with variation of epoxy resin thickness and diameter. Surface discharge voltage increases as the thickness and the diameter of epoxy resin.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.23 no.2
• /
• pp.168-174
• /
• 2009

In this paper Gel polymer electrolyte using Poly(Vdf-HFP) was fabricated and compared with liquid type electrolyte. The chemical structure and ingredients of fabricated gel electrolyte was investigated and identified to gel polymer electrolyte by FTIR, gel electrolyte was verified to polymer state by SEM From the experiment result, the better component ratio of Propylene carbonate and Diethyl carbonate for gel type electrolyte was 5 : 5. The conversion efficiency of fabricated DSCs using gel electrolyte was $3{\sim}4[%]$, expected to alternate with liquid type electrolyte.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2008.10a
• /
• pp.7-11
• /
• 2008

The fluorescent lamp is one of a discharge lane that is used by electric discharge to transfer from electrical energy to light The fluorescent lamp needs a ballast stabilizer when turn it on because it has negative resistance. Characters of electric discharge and transformed characters of ballast stabilizer are connected closely. Therefore, bring out best design directive that consider economical efficiency and term of a application is very important for both characters matching. In this case, we will team to develop tester and functions for expression for recognizing the end of fluorescent lamp life to solve fire problem and losing efficiency of light when a fluorescent lamp goes the end of the expected its life span.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.15 no.2
• /
• pp.49-56
• /
• 2001

This paper describes the improvement of passenger's comfort by analyzing the debasement of early adapted ATO control pattern. First we give the characteristics of ATO controller, principle of running control, distance & velocity calculation methods used mainly in INCHEON subway UNE 1 and then analyze the ATO control pattern. For early control pattern, we reviewed it in view of passenger's comfort while keeping the track conditions. In order to achieve the improvement of passenger's comfort we propose the modification of early ATO control pattern based on JERX characteristics. Simulation and application test are performed to prove the effectiveness of modified ATO control pattern.