• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.1
• /
• pp.94-98
• /
• 2010

The auxiliary power supply for satellite should make the power safe and support it for subsystems during its operational lifetime. Several contstraints should be required to get high reliability. In this paper, the auxiliary power supply was satisifed and designed to be satisified with some contstraints. Control circuits for the auxiliary power supply used majority voter circuits to remove the single point failure. To verify majority voter circuits, proto-type auxiliary power supply was manufactured and tested.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.4
• /
• pp.285-291
• /
• 2001

An 8-b$\times$8-b adiabatic pipelined multiplier is designed. Simplified four phase clock generator is also designed to provide supply clocks for adiabatic circuits. All the clock line charge on the capacitive interconnections is recovered to save energy. Adiabatic circuits are designed based on ECRL(efficient charge recovery logic) and are integrated using 0.6${\mu}{\textrm}{m}$ CMOS technology. The efficiency of proposed supply clock generator is better than the previous one by 4~11%. Simulation results show that the power consumption of adiabatic pipelined multiplier is reduced by a factor of 2.6~3.5 compared to a conventional pipelined CMOS multiplier.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.758-761
• /
• 2003

We have designed 5 V/500 mA transless type power module by using semiconductor switching technique, key technique for small size of power supply system. The power module is suitable to a small sized electronic system using a single power supply. It is composed of switching circuit using voltage drop type chopper method, control circuit, voltage detect circuit, and constant voltage circuit, and is fabricated to hybrid-IC type. The switching regulator power supply circuit, designed in this study, has satisfied the electrical characteristics of 5 V/500 mA transless type power module.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.224-226
• /
• 2020

본 논문은 빠른 상승 시간과 짧은 펄스폭을 위한 펄스 전원장치의 설계에 대해 다룬다. 이를 위해서 적합한 방전 스위치의 선정과 높은 상승률을 가진 동기화된 게이트 전압을 만들어 내는 게이트 구동 회로의 설계가 진행 되었다. 방전 스위치로 IGBT가 선정되었으며, 방전 스위치들의 동기화된 빠른 게이트 드라이빙을 위한 펄스 컨트롤러 인버터와 게이트 드라이브 회로의 설계 및 동작에 대한 분석이 진행 되었다. 실험을 통해 펄스 컨트롤러 게이트 드라이빙 시스템에 대한 검증이 이루어졌고, 무유도 저항을 사용한 10 kV, 50 kHz 조건에서 펄스 출력 실험을 통해 20 ns 이하 상승시간과 100 ns 펄스폭을 갖는 펄스 전원 장치의 출력을 확인 하였다.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.101-108
• /
• 2004

A 16-bit adiabatic ALU(arithmetic logic unit) is designed. A simplified four-phase clock generator is also designed to provide supply clocks for the adiabatic circuits. All the clock line charge on the capacitive interconnections is recovered to recycle energy. Adiabatic circuits are designed based on ECRL (efficient charge recovery logic) using a 0.35${\mu}{\textrm}{m}$ CMOS technology. The post-layout simulation results show that the power consumption of the adiabatic ALU including supply clock generator is reduced by a factor of 1.15-1.77 compared to the conventional CMOS ALU with the same structure.

• Proceedings of the KIPE Conference
• /
• 2019.07a
• /
• pp.254-256
• /
• 2019

본 논문은 파워셀 구조를 기반으로 설계된 양극성 펄스 전원장치에 대하여 소개한다. 파워셀은 풀브릿지 구조를 기반으로 설계되었으며, 833V를 출력하는 각 셀이 직렬로 연결되어 고전압을 생성하는 구조를 갖는다. 모든 파워셀의 방전 스위치를 구동하기 위해서 절연된 전력과 신호의 동시공급이 가능한 게이트 회로 구동방안이 제안되었다. 양극성 펄스 출력을 위한 파워셀의 각 래그의 단락을 방지하기 위한 게이트 회로가 설계되었다. 설계된 양극성 펄스 파워 모듈레이터의 동작을 검증하기 위해 테스트 회로가 구현되었다. 시험회로는 출력전압, 펄스 폭, 반복률 가변 조건에서 테스트 되었으며, 이를 통해 제안하는 양극성 펄스 파워 모듈레이터의 구조 및 게이트 구동회로의 신뢰성이 검증되었다.

• Proceedings of the KAIS Fall Conference
• /
• 2010.11a
• /
• pp.172-175
• /
• 2010

본 논문에서는 GaN HEMT를 이용하여 Jamming용 System에 사용될 수 있는 고효율 및 고출력 특성을 가지는 광대역 Amplifier를 제작하였다. Jamming System에서 핵심이 되는 Amplifier는 넓은 범위의 주파수에서 통상적으로 사용되는 출력 신호에 비해 보다 높은 출력의 신호를 구현하는 것이 중요하다. 본 논문에서는 GaN HEMT에 안정적인 전원 공급을 위한 음 전원 Bias 제어 회로와 Sequence 회로 및 온도에 따른 Gain 보상 회로를 구현하였으며, 500~2500MHz의 광대역에서 동작하면서 50W 이상의 출력을 낼 수 있도록 설계하였다. 출력 전력이 향상과 안정적인 동작을 위해 Main 출력 단은 60Watt 급의 GaN HEMT 소자와 광대역 Coupler를 이용하여 Balanced Structure로 설계하였다. 제작된 광대역 Amplifier는 30V 단일 전원에서 동작하도록 설계되었고, 크기는 140*90mm이다. 동작주파수 대역(500~2500MHz)에서 Small Signal Gain 63dB와 Gain Flatness ${\pm}$2dB, -10dB 이하의 Input Return Loss를 가진다. CW(Continuous Wave) Signal을 이용하여 측정하였으며, 50Watt 이상의 Saturation Power에서 최대 45%, 최소 28% 정도의 효율 특성을 보였다.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.855-860
• /
• 2016

This study describes the design and implementation of digital Payload power supply. We materialized the interface of the PLDIU and power supply of a satellite bus, and minimized the potential for the occurrence of such erroneous operation circuit ESD through the WCA of the space environment. We designed a reliable power supply through simulation for a TID according to the vibration generated during the launch and space radiation environment, and found no problem in the function and performance through the test space environment after production.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.16 no.3
• /
• pp.437-442
• /
• 2021

This study describes the design and implementation of power supply of dehop/rehop transponder of EQM(Engineering Qualification Model). We materialized the interface of the PLDIU and power supply of a satellite bus, and minimized the potential for the occurrence of such erroneous operation circuit ESD through the WCA of the space environment. We designed a reliable power supply through simulation for TID about space radiation and simulation of the vibration generated during it launched, and we confirmed that it satisfies the environmental test specification through the test space environment after production.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.53 no.10
• /
• pp.133-137
• /
• 2016

Use of UV gel for nail management have been increasing gradually. In order to develop an UV lamp necessary to UV gel, in this study, we was designed circuits of the UV-LED lamp. Power supply part that supplies constant power to the several UV-LEDs, was designed the circuit with the method of DC-DC converter. Taking into account the direction of the thumb nail and the position of the little finger nail, it was placed UV-LEDs. Input power of the power supply part was used as a battery voltage of 3.8[V]. The output voltage of the power supply part was appeared in approximately 3.1[V]. And in order to examine the state of change of the output voltage according to the amount of current consumption of UV-LEDs, after inserting of load resister, the output voltage was more than about 3.0[V] in the simulation results of the power supply part while changing the resistance value.