• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1400-1405
• /
• 2004

Experimental study is performed to investigate the effect of heat load and operating temperature on the thermal performance of a heat pipe with screen mesh wick. The heat pipe was designed in 200 screen meshes, 500mm length and 12.7mm O.D tube of copper, water as working fluid(4.8g) and nitrogen as non-condensible gas(NCG). The heat pipe used in this study has evaporator, condenser and adiabatic section, respectively. Experimental data of axial wall temperature distribution is presented for heat transport capacity, the temperature of cooling water of condenser, inclination angle, and operating temperature. For the results from this study, it is found that, for the same charging mass of working fluid, the initial operating temperature and the overall wall temperatures of heat pipe are higher for NCG charging mass of $5.0{\times}10^{-6}kg$ and $3.4{\times}10^{-6}kg$, than that of $1.0{\times}10^{-6}kg$.

• Proceedings of the SAREK Conference
• /
• 2007.11a
• /
• pp.176-181
• /
• 2007

This study aims to evaluate theoretically heat transfer characteristics and heat flux performance in ondol system of dried type is composed of panel of ceramics to improve of thermal conductivity and fin to expand heat. To this end, we analyzed effect of design factors(temperature of hot water, set temperature of room and thermal conductivity of finishing materials) in ondol system of dried type by heat transfer analysis. The main results of this study are summarized as follows; The deviation of heat flux and temperature was reduced by heat expansion from fin decreasing heat loss generated in air layer. The temperature and heat flux in upper finishing materials surface linearly increased according to temperature increment of hot water, but the temperature distribution in upper surface was assessed uneven. The greater heat resistance value of upper finishing materials, the deviation of maximum temperature and minimum temperature was decreased. Also, we suggested a basic design data about ondol system of dried type through an analysis of simulation results on heat transfer characteristics and heat flux performance.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.17 no.10
• /
• pp.891-897
• /
• 2005

The characteristics of energy Performance for total heat exchanger have been investigated under various conditions. In cooling operation the latent and enthalpy efficiency are affected by the difference of absolute humidity ratio between indoor and outdoor air. In addition to this the characteristics of absorbing material in the element affects the energy performance. Low dry bulb temperature of indoor air or high absolute humidity ratio in outdoor air give high latent and enthalpy efficiency even with the same temperature difference of dry bulb temperate between indoor and outdoor air.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.24 no.7
• /
• pp.553-559
• /
• 2012

A plate-fin heat exchanger is a type of heat exchanger widely used in air conditioners, and tubes and fins are tightly assembled by the mechanical expansion process of tubes. The tube expansion process deforms the grooves inside the tube, and the groove shapes also affect the adhesion between tubes and fins. In this study, the adhesion and heat transfer performance affected by the tube expansion of the non-uniform groove shape tube with different heights are investigated by both analysis and experiments. From the analysis method, it was shown that the contact pressure of non-uniform groove tube is higher than that of the uniform groove tube, and the most appropriate high groove number of the non-uniform groove tube is designed for the maximum contact pressure. From the experimental results, the decreasing rate of the condensation heat transfer coefficient is smaller in the non-uniform groove tube with different heights, compared to the conventional uniform groove tube. Also, the air-side heat transfer coefficient of the non-uniform groove tube with different heights is higher than that of the uniform groove tubes.

• Journal of the Korean Solar Energy Society
• /
• v.22 no.4
• /
• pp.35-43
• /
• 2002

This research makes that quantitative radiation property of an actual town ward is obtained in quest of the parameter with regard to a radiation heat transfer property and set up several town ward models that reproduced a solid form of a city along the attribute of the city. A regular trend possibility that is able to evaluate a radiation characteristics of a town ward quantitatively from a town ward guideline and confirmation that is produced about each parameter as a result of a numerical value simulation it obtained. This research shot a coefficient of Gebhart's emission absorption. sky radiation absorption rate direct solar radiation absorption rate the parameter with regard to a radiation heat transfer characteristics of a town ward in each town ward model and a volume rate of a town ward advances case study under regular such condition and shot the absorption rate, direct and others days and calculated an absorption rate and checked about the relation between a town ward and each radiation heat transfer property of a city.

• Korean Journal of Materials Research
• /
• v.8 no.8
• /
• pp.726-732
• /
• 1998

가압 경수로형 원전에 사용되는 Alloy 600 증기발생기 전열관재료의 입계응력부식균열 거동에 미치는 냉간변형의 영향을 1차 냉각수 모사조건에서 정속인장시험방법으로 조사하였다. 인장 냉간변형은 응력부식균열을 크게 가속화 시키지는 않았으며 변형량이 25%이상인 경우에는 응력부식균열이 발생하지 않았다. 이 현상은 냉간 변형량 및 형태에 따른 미소변형 및 응력의 불균질성에 영향을 받는 것으로 사려되며 응력의 크기는 직접적인 영향을 주지 않는 것으로 보인다. 국부적인 큰 응력구배가 존재하는 경우 균열의생성 및 성장이 현저히 가속화되었는데 이는 원전 1차측 응력부식균열 기구가 응력구배에 의존하는 과정과 연관되어 있다는 증거이다. Hump 시편을 이용한 정속인장시험방법은 짧은 실험기간내에 원전 1차측 응력부식균열 특성을 평가할 수 있는 방법이었다.

• Proceedings of the Korea Institute of Fire Science and Engineering Conference
• /
• 2009.04a
• /
• pp.487-492
• /
• 2009

This study was performed FE numerical analysis under 120-minute fire conditions, using the ABAQUS, a wide use software, on the basis of the test results by concrete tunnel lining fire strengths (ISO, RWS, and MHC). The concrete material test was to secure the material properties of concrete linings, which were numerical analysis input conditions. And then built the material properties, such as specific heat, heat transfer rate, heat expansion rate, density, elasticity coefficient and compression strength under high temperature conditions, as database at 20 $^{\circ}C$ to 800 $^{\circ}C$, applying them to analysis as input values. As a result, the tunnel linings under RWS fire conditions saw fire temperature rose to maximum 1119 $^{\circ}C$at the location of 5 mm above a thermal surface, and saw surface temperature amount to 1214 $^{\circ}C$ in the middle part.

• Journal of IKEEE
• /
• v.23 no.2
• /
• pp.364-369
• /
• 2019

The ratios of compliant branch circuit of leakage current and insulation resistance were 68.4% and 90.8%, respectively at the lamp load, 64.6% and 96.5% at the heat load, 86.7% and 88.9% at the power load. Limit of residual current of the zero phase secondary current value at the zero phase primary current was 100 A when rated primary current 400 A more than. The reason why the ratio of branch circuit of the leakage current was less than the ratio of compliant branch circuit of the insulation resistance might be that the leakage current includes the capacitive leakage current and the zero phase current.

• Proceedings of the Korea Information Processing Society Conference
• /
• 2013.11a
• /
• pp.1382-1385
• /
• 2013

본 논문에서는 로봇의 움직임 특성을 추출하여 로봇 시스템의 신뢰성을 평가하는 방법을 제안한다. 원자력 발전소 증기 발생기 전열관의 비파괴 검사에 사용되는 ECT 검사용 Probe 가이드 로봇 (이하 증기발생기 로봇으로 기술)을 대상으로 하였다. 증기발생기 로봇의 동작 상태를 감시하기 위해 관측 카메라가 설치된다. 증기발생기 수실은 로봇 설치 및 해체를 위한 원형의 출입구 (Man Way)를 제외하고는 밀폐된 공간이다. 증기 발생기 전열관의 비파괴 검사 중에는 로봇과 로봇의 동작을 감시하는 관측 카메라만 설치된다. 관측 카메라가 고정되어 있다면, 배경의 변화를 야기하는 외란은 없다고 가정할 수 있다. 시간적으로 이웃하는 2 개의 관측 영상을 미분 (차 영상) 처리하면, 로봇 시스템의 이동 성분만 추출된다. 이러한 이동성분의 크기를 계산하여 로봇의 전체 행정거리 (ECT Probe를 검사위치에 안내하기 위해 로봇 기구부가 움직이는 범위)에 대해 영상 프레임 단위로 전개하면 특정의 고유 궤적이 나타난다. 이러한 고유 궤적과 다른 패턴을 보이는 로봇의 움직임 궤적은 에러로 간주한다. Burn-in 시험 (원자력 발전소 현장에 투입하기 전에 실험실에서 현장 적용의 타당성을 검증하기 위해 수행하는 시험) 중에 있는 증기발생기 로봇에 대해 본 논문에서 제안한 방법으로 신뢰성 평가를 수행하였으며, 그 결과 및 문제점 등에 대해 기술한다.

• Journal of Energy Engineering
• /
• v.5 no.2
• /
• pp.115-122
• /
• 1996

Heat transfer characteristics of low temperature latent heat storage systems have been examined for the circular finned and unfinned tubes using Na$_2$B$_4$O$\_$7/10H$_2$O as a phase change material. In order to reduce the supercooling of PCM, 3 wt% of Na$_2$B$_4$O$\_$7/10H$_2$O was added as the nucleating agent and 2.2 wt% of acrylic acid sodium sulfate was used as the thickener. The heat storage vessel has dimension of 530 mm height, 74 mm 1.D. and inner heat transfer tube is 480 mm height and 13.5 mm O.D. Water was employed as the heat transfer fluid. During the heat recovery experiment, the heat recovery rate was affected by the flow rates and inlet temperature of heat transfer fluid. The enhancement of heat transfer by fins over the unfinned tube system was found to be negligible in the thin finned tube systems, whereas the heat transfer coefficient in the thick finned tube system is approximately 60% higher than that in the unfinned lobe system. The experimentally determined heat transfer coefficient for the unfinned tube and thick finned tube systems are 150-260 W/㎡$^{\circ}C$ and 230-530 W/㎡$^{\circ}C$, respectively. The fin efficiency based on the heat transfer coefficient and area increased by fins was found to be 0.05 and 0.26 for the thin and the thick finned tube systems.