• International Journal of Highway Engineering
• /
• v.11 no.1
• /
• pp.1-12
• /
• 2009

A new mix design procedure for cold in-place recycling using foamed asphalt (CIR-foam) has been developed for Iowa Department of Transportation. Some strengths and weaknesses of the new mix design parameters were considered and modified to improve the laboratory test procedure. Based on the critical mixture parameters identified, a new mix design procedure was developed and validated to establish the properties of the CIR-foam mixtures. As part of the validation effort to evaluate a new CIR-foam mix design procedure, dynamic moduli of CIR-foam mixtures made of seven different reclaimed asphalt pavement (RAP) materials collected throughout the state of Iowa were measured and their master curves were constructed. The main objectives of this study are to provide: 1) standardized testing procedure for measuring the dynamic modulus of CIR-foam mixtures using new simple performance testing (SPT) equipment; 2) analysis procedure for constructing the master curves for a wide range of RAP materials; and 3) impacts of RAP material characteristics on the dynamic modulus. Dynamic moduli were measured at three different temperatures and six different loading frequencies and they were consistent among different RAP sources. Master curves were then constructed for the CIR-foam mixtures using seven different RAP materials. Based upon the observation of the constructed master curves, dynamic moduli of CIR-foam mixtures were less sensitive to the loading frequencies than HMA mixtures. It can be concluded that at the low temperature, the dynamic modulus is affected by the amount of fines in the RAP materials whereas, at the high temperature, the dynamic modulus is influenced by the residual binder characteristics.

• International Journal of Highway Engineering
• /
• v.12 no.1
• /
• pp.79-86
• /
• 2010

Cold in-place recycling (CIR) using emulsified asphalt or foamed asphalt has become a more common practice in rehabilitating the existing asphalt pavement due to its cost effectiveness and the conservation of paving materials. As CIR continues to evolve, the engineered emulsified asphalt was developed to improve the field performances such as coating, raveling, retained stability value and curing time. The main objective of this research is to compare the laboratory responses of the engineered emulsified asphalt (CIR-EE) mixtures against the foamed asphalt (CIR-foam) mixtures using the reclaimed asphalt pavement (RAP)materials collected from the CIR project on U.S. 20 Highway in Iowa. Based on the visual observation of laboratory specimens, the engineered emulsified asphalt coated the RAP materials better than the foamed asphalt because the foamed asphalt is to create a mastic mixture structure rather than coating RAP materials. Given the same compaction effort, CIR-EE specimens exhibited lesser density than CIR-foam specimens. Both Marshall stability and indirect tensile strength of CIR-EE specimens were about same as those of CIR-foam specimens. However, Marshall stability and indirect tensile strength of the vacuum-saturated wet specimens of CIR-EE mixtures were higher than those of CIR-foam mixtures. After four hours of curing in the room temperature, the CIR-EE specimens showed less raveling than the CIR-foam specimens. On the basis of test results, it can be concluded that the CIR-EE mixtures is less susceptible to moisture and more raveling resistant than CIR-foam mixtures.

• International Journal of Highway Engineering
• /
• v.13 no.2
• /
• pp.139-145
• /
• 2011

The practice of asphalt pavement recycling has grown rapidly over the decade, one of which is the cold in-place recycling with the foamed asphalt (CIR-foam) or the emulsified asphalt (CIR-emulsion). Particularly, in Iowa, the CIR has been widely used in rehabilitating the rural highways because it significantly increases the service life of the existing pavement. The CIR layer is typically overlaid by the hot mix asphalt (HMA) to protect it from water ingress and traffic load and obtain the required pavement structure and texture. Most public agencies have different curing requirements based on the number of curing days or the maximum moisture contents for the CIR before placing the overlay. The main objective of this study is to develop a moisture loss index that the public agency can use to monitor the moisture content of CIR layers in preparation for a timely placement of the wearing surface. First, the moisture contents were measured in the field using a portable time domain reflectometry (TDR) device. Second, the weather information in terms of rain fall, air temperature, humidity and wind speed was collected from the same location. Finally, a moisture loss index was developed as a function of initial moisture content, air temperature, humidity and wind speed. The developed moisture loss index based on the field measurements would help the public agency to determine an optimum timing of an overlay placement without continually measuring moisture conditions in the field.

• International Journal of Highway Engineering
• /
• v.3 no.1 s.7
• /
• pp.177-184
• /
• 2001

A recycling agent has been manufactured on the basis of the chemical composition of reclaimed asphalt binders and virgin asphalt binders. The chemical compositions of reclaimed asphalt binders extracted from reclaimed asphalt pavements have been analyzed according to the ASTM method and the results were compared to those of virgin asphalt binder AP-3. Reclaimed asphalt binders have shown that asphaltenes was increased whereas saturates, naphthene aromatics, and polar aromatics fractions were decreased. A recycling agent made of aromatic compounds, in which its chemical composition is similar to the aromatics fraction in asphalt binders, has been produced to reduce the amount of asphaltenes in reclaimed asphalt hinders. The evaluation of the recycling agent produced was performed by testing ductility, rolling and ball softening point, penetration at $25^{\circ}C$ and viscosity at $60^{\circ}C$. It was found that, by adding the recycling agent 20% by weight to the reclaimed asphalt binders, the physical properties of reclaimed asphalt binders was recovered to the level of virgin asphalt binder AP-3.

• 한국도로학회지:도로
• /
• v.5 no.4 s.18
• /
• pp.36-46
• /
• 2003

포장구조체에서 요구되는 강도를 갖게 하는 구조 설계의 방법은 경험적 절차부터 반역학적 절차까지 발전되어 왔다. 재생 가열아스팔트혼합물이 기존의 가열아스팔트혼합물(HMA)과 비교하여 비슷하거나 때에 따라 더 좋은 성능을 가져오므로, AASHTO설계지침서에서는 본질적으로 재생(recycled) HMA 재료와 신생(virgin) HMA 재료간의 차이가 없다고 기술하고 있으며, 기존 HMA 재료에 사용되는 덧씌우기설계법의 구조회복 분석방법(structural rehabilitation analysis method)을 재생포장설계에도 권장하고 있다. 재생 가열아스팔트의 설계를 위한 AASHTO 방법은 설계교통량, 교통량 및 수행능력예측의 신뢰수준, 공용기간, 그리고 포장상태 평가지수에 의하여 결정된 포장구조체에서 요구되는 포장두께지수(SN)에 기초한다. 포장두께지수(SN)는 포장층 두께, 상대강도계수, 각 층의 배수조건들의 곱의 조합으로서 나타내어질 수 있다. 덧씌우기로 간주될 수 있는 재생된 층의 포장두께지수(SN)는 기존 포장에서의 포장두께지수와 보강된 포장에서 요구되는 포장두께지수의 차이에 의하여 계산되어질 수 있다. 상대강도계수의 값은 AASHTO 설계지침에 명시되어 있다. AI 방법은 교통량, 노상의 회복탄성계수, 그리고 설계두께를 계산하기 위한 표층과 기층의 종류를 사용한다. 이 방법은 재생된 가열혼합물질과 기존의 가열혼합물질과는 거의 비슷한 성능을 나타낸다고 본다. 또다른 AI 방법에 의하면 재생된 층은 덧씌우기층이라고 간주하고, 현재의 포장두께와 요구되어지는 포장두께 사이의 차를 이용하여 재생될 층의 두께를 산정한다. 소요되는 덧씌우기 두께는 포장의 현장 상태지수(condition rating)와 각 종류에 따른 포장체와 포장재료가 아스팔트 콘크리트층의 등가두께로 전환되어 나타나는 방법에 근거하여 결정될 수 있다. 또 다른 방법은 포장체 각 층의 물성과 하중을 이용한 컴퓨터 프로그램에 의하여 산정된 하중-변형 응답에 의한 설계 방법을 포함한다. 이런 방법들에서는 포장체는 탄성이나 점탄성층 위에서 탄성이나 점탄성 거동을 보인다고 가정한다. 재생 상온혼합물에서의 AASHTO 설계 방법은 가열혼합물의 설계방법과 유사하다. 그러나, 재생 상온혼합물에서의 상대강도계수는 시공방법에 좌우되므로, 기술자의 판단을 근거로 하여 결정되어져야 한다. AI방법에서는 포장구조체를 다층탄성구조라고 보고, 노상의 강도와 설계 교통량을 근거로 요구되는 포장두께를 결정한다. 재생 상온혼합물 기층의 두께는 재생 상온혼합물 기충 위에서 가열아스팔혼합물에 대하여 산정된 덧씌우기 두께를 이용하여 결정할 수 있다. 아스팔트 표면의 재생은 기존 포장의 구조적 능력을 정상적으로 개선할 수 없으므로, 표면 재생의 두께를 설계하는 방법은 없다. 그러나, 임의의 덧씌우기 두께는 기존의 덧씌우기 설계법에 기초하여 산정 할 수 있다. 만약 덧씌우기가 승차감만을 개선시킨다고 여겨진다면, 혼합물에서 사용되어지는 최대 골재 크기에 기초한 최소 두께를 결정할 수 있다.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.4
• /
• pp.82-88
• /
• 2012

The usage of recycling agent is the most effective way of enhancing the performance of recycled asphalt pavement. Generally, many countries accepted these recycling agents retarding the various types of cracks resulted in binder aging. Contrary to such general tendency, recycling agents are used as very small amount in domestic recycling plant. The main reason of this is relatively high price of recycling agent. Even though agent price is high, agent can be a effective and economical way of alternative in asphalt recycling. In this study, penetration and softning point test performed by using RTFO(Rolling Thin Film Oven) aged binder. And, PG(Performance Grade) at high temperature, fatigue and MSCR(Multi Stress Creep and Recovery) tests exercised. The oil type agent is worked well to retrieving target penetration number. In PG test, $G^*/sin{\delta}$ of agents identically showed high value and polymer type agent is good at recovery value.

• 한국방재학회:학술대회논문집
• /
• 2009.02b
• /
• pp.81.1-81.1
• /
• 2009

• International Journal of Highway Engineering
• /
• v.12 no.4
• /
• pp.203-209
• /
• 2010

The base asphalt mixtures that used the waste recycle asphalt correcting from the four different overlay construction sites in Seoul city were made using the foamed asphalt method. The sample mixtures were made in different ratio of the recycle asphalt and new asphalt material and the performance of the mixtures of the different ratio was investigated in the laboratory. The laboratory tests includes the Marshall test, the indirect tensile test, the resilient modulus test, the creep test and the wheel tracking test. The test of the recycle foamed asphalt mixtures(RFA) were compared with the those of the recycle hot mix asphalt(RHA) mixtures. The performance of the RFA is comparable to that of the RHA. On the other hand, the indirect tensile strength of the RFA in dry condition is lower than that of RHA and the indirect tensile strength of the RFA in wet condition is much lower than that of the RHA.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.6 no.2
• /
• pp.112-118
• /
• 2011

The recycled asphalt concrete has gotten increasing attention due to the environmental issues. The volume of reclaimed asphalt has increased significantly for last few years because of city remodeling, pavement maintenance, utility excavation, and road widening. Considering the value of reclaimed asphalt, it is rather used for the recycled asphalt concrete than it is used for fill and cover up material instead of soil. This research will be a supplements incomplete issues from existing research results and suggests the quality control guideline for recycled asphalt concrete and upcoming laws. As the first step of research, the trial construction of RAP(Recycled Asphalt Pavement) performed in expressway construction sites. These trial construction sites have been checked every years. And another construction sites studied and selected for more deeper performance check of RAP. For this checks, we used automatic pavement survey equipment and computerized analysis tools. Also, DSR(Dynamic Shear Rheometer) was used for the fatigue life calculation of binder blends(RAP and virgin binder). As a consequence of this research, the application of recycled asphalt provides good enough quality for highway construction. The preceeding literatures reviewed shows that the asphalt rejuvenator are used in many countries but that type of chemical agent are not used in Korea. By using the data of trial construction and mix design in Chongwon-Sangju construction lane, the surface and base courses consisted with the 10% and 30% rap mix asphalt section maintains good performance for up to 7 years. Through the performance check and laboratory tests(DSR), the quality control and mixture's low temperature prevention are the important factor and chemical agent necessary for increasing the fatigue life of RAP binder.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.36 no.6
• /
• pp.1101-1107
• /
• 2016

As an increase in the amount of RAP, there are growing interests in recycling asphalt concrete. In case of using the RAP as recycled asphalt pavement, it tends to be quality deteriorate. Therefore, the amount of RAP using is advised to be limited or has to be used with rejuvenator. In this study, asphalt mixture containing WMRA was analyzed to be used up to 50% for the sake of convenience on the process. As the results of evaluation, there was no significant difference in case of using 30% of RAP in the test of Marshall stability. However, in case of WMRA using up to 50%, it was satisfied criteria by flow value at 34.7. Further, result of toughness test was found that the crack resistance showed 55% higher than using straight asphalt when using WMRA binder up to 50%. According to the results of directly comparing crack resistance through repeated direct tensile test, it was shown that the fatigue crack resistance of WMRA pavement was increased by 263%. Therefore, it was shown that WMRA binder was effective in recycling RAP because WMRA binder could increase the percentage of RAP using up to 50%.