X-ray powder diffraction study was conducted on the bulk modulus and phase transition behavior of synthetic zeolite X under high temperature and high pressure. Water and HCO3- solution were used as a PTM. Sample was heated and pressurized up to 250 ℃ and 5.18 GPa. The change of unit cell volume and phase transition were observed by X-ray diffraction. The lattice constants and unit cell volume of zeolite X, gmelinite, natrolite, and smectite were calculated using the GSAS2 program to which Le Bail's whole powder pattern decomposition (WPPD) method was applied. The bulk modulus of each zeolite X and smectite were calculated using the EosFit program to which the Birch-Murnaghan equation was applied. The bulk modulus of zeolite X is 89(3) GPa in water run, and zeolite X is 92(3) GPa in HCO3- solution run. In both run, pressure induced hydration (PIH) occurred due to the inflow of PTM into the zeolite X framework at initial pressure. Zeolite X transited to gmelinite, natrolite, and smectite in water run. Zeolite X, however, transited to smectite in HCO3- solution run. Interzeolite transformation occurred in water run, and did not occur in HCO3- solution run, which is assumed that conflict between the environment to form zeolite and the pH of the HCO3- solution.
Ji-Yoon Yang;Gyeong-Han Lee;Sang-Woo Kim;Soo-Yong Lee
Journal of Aerospace System Engineering
/
v.18
no.3
/
pp.70-75
/
2024
The insulation performance of a common bulkhead propellant tank for small launch vehicles with variations in insulation thickness was analyzed. The common bulkhead propellant tank composed of a single part allows for lightweight design, as it eliminates the need for tank connections. However, problems such as propellant loss and ignition delay due to heat transfer caused by temperature differences between oxidizer and fuel may arise. Therefore, it is essential to verify the insulation performance of the common bulkhead structure that separates the oxidizer tank and fuel tank. In this study, transient heat transfer analysis was conducted for propellant tanks with insulation thicknesses of (50, 55, 60, 65, and 70) mm to analyze the insulation performance using boil-off mass. Subsequently, the boil-off mass of the oxidizer generated during the first-stage flight time of the propellant tank was determined. The results confirmed that increasing the insulation thickness reduces the boil-off mass, thereby improving the insulation performance.
This experiment was performed to understand the relationship between uptake of Fe and Mn by plants, red pepper and tomato, and soil physico-chemical properties under different soil conditions at an environmentally controlled chamber in NAAS(National Academy of Agricultural Science) in 2008. After the dipping for 3 days, four treatments, dipping, dipping+aeration, drainage, drainage+aeration, were set up to investigate the changes in soil redox potential and moisture content. Drainage+aeration changed soil to the oxidation condition from 72 hrs of treatment, and soil moisture content was immediately reduced after treatment. Uptake of Fe and Mn of red pepper was investigated with two treatments, soil only and the mixed[soil(50%) : bed soil(35%) : bark(15%)]. Red pepper leaves taken at 30 days after treatment absorbed excessively Mn from the treatment of soil only and the mixed, and thus uptake of iron was strongly reduced. Also, uptake pattern of Fe and Mn of tomato was examined with four treatment, soil only, soil(50%) + rice straw(50%), soil(50%) + compost(50%) and soil + aeration. Contents of Fe and Mn in tomato leaves was measured at 60 days after treatment. Fe content was the greatest in soil(50%) + compost(50%) whereas Mn content was the highest in soil only. As a result of this experiment, plant growth was stronger influenced by soil moisture content than redox potential or porosity, and the oxidation status of soil was likely to promote that plant predominantly absorbed Mn from soil and thus resulted in Fe deficiency.
Kim, Do-Yeon;Lee, Soo-Hyun;Kim, Min-Ju;Shin, Kyoo-Ho
The Journal of the Korean bone and joint tumor society
/
v.15
no.1
/
pp.34-43
/
2009
Purpose: Glomus tumors are rare benign vascular tumors, usually located in the skin or soft tissue of extremities. Approximately 30-50% of glomus tumors occur in subungal area, but glomus tumors have been described in every location even where glomus bodies are not or rarely present. The purpose of this study was to identify clinical, histologic and MRI characteristics of soft tissue glomus tumor. Materials and Methods: Between 1993 and 2008, eight patients underwent surgery of soft tissue Glomus tumor at our institution. Exclusion criteria were patients with Glomus tumors in digits, stomach, trachea and glomus tympanicum. We analyzed medical records, interviews, physical examinations, MR findings and histolocial types retrospectively. Results: There were four men and four women. The mean age was fourty-seven years. The mean prevalence time was eight-point-nine years. In the classic triad of symptoms, all eight patients had pain and tenderness. Two patients complained of cold sensitivity. Two showed skin color changes. After surgery, two showed symptom improvement (VAS $9^{\circ}{\rightarrow}8$, $8^{\circ}{\rightarrow}5$) and?six showed complete disappearance of symptoms. Slightly symptom improvemented (VAS $9^{\circ}{\rightarrow}8$) one had additional surgery two times after first surgery due to relapse/remaining Glomus tumor. The mean size was 13.9 mm. In histology, six were 'solid glomus tumor', one was a mixture of 'solid glomus tumor' and 'lomangioma' and one was 'malignant glomus tumor'. MR findings showed isointense signal on T1 image, high signal on T2 image and strong enhancement on the Gadolinium enhanced image. Conclusion: Glomus tumor has low recurrence rate and malignant change, rapid diagnosis and surgical excision is critical in treatment to prevent unnecessary pain of patient.
Sambucus pendula Nakai, which is an endemic on Ulleung Island of Korea, is characterized by a large pendulous inflorescence and small fruit. A set of 256 individuals were used to investigate the patterns of intraspecific variation of S. racemosa subsp. kamtchatica, S. racemosa subsp. sieboldiana, and S. williamsii including S. pendula using PCA (principal components analysis). This analysis showed that S. pendula was distinct based on its large inflorescence and long peduncle. Our data showed a morphological distinction between subsp. kamtchatica from northeastern areas and subsp. sieboldiana from Jeju Island, but the two taxa overlap in the southern and eastern parts of Korea in terms of chromosome number, color of style, and allozyme data. Our study agrees that S. pendula on Ulleung Island may be the result of genetic drift that occurred during isolation since the Quarternary period. This has been suggested as a reason for the genetic differences observed between two taxa and would explain the unique variation patterns of S. pendula. However, the morphological differentiation between the S. racemosa complex and S. pendula is not considered sufficient to warrant recognition of specific status. Therefore, we recommend that only one polymorphic species of S. racemosa in Eurasia be recognized and that S. pendula be considered a subspecies of S. racemosa.
Kim, Hyungmin;Lee, Byokkyu;Woo, Jaegyung;Hur, Ik;Lee, Junki;Lee, Sugon
Journal of the Korean GEO-environmental Society
/
v.20
no.5
/
pp.13-21
/
2019
There are many cuts or natural rock slopes that remain stable for a long time in the natural environment with steep slopes ($65^{\circ}$ to $85^{\circ}$). In terms of design practice, the rock mass consisting of similar rock condition and geological structures is defined as a good continuum rock slope, and during the process of decision making angle of this rock slope, it will be important to establish the geotechnical properties estimating method of the continuum rock on the process of stability analysis in the early stages of design and construction. In this study, the stability analysis of a good continuum rock slope that can be designed as a steep slope proposed a practical method of estimating the shear strength by induced from the Hoek-Brown failure criterion, and in addition, the design applicability was evaluated through the stability analysis of steep rock slope. The existing method of estimating the shear strength was inadequate for practical use in the design, as the equivalent M-C shear strength corresponding to the H-B envelope changes sensitively, even with small variations in confining stress. To compensate for this problem, it was proposed to estimate equivalent M-C shear strength by iso-angle division method. To verify the design applicability of the iso-angle division method, the results of the safety factor and the displacement according to the change in angle of the cut slope constructed at the existing working design site were reviewed. The safety factor is FS=16~59 on the 1:0.5 slope, FS=12~52 on the 1:0.3 slope, most of which show a 10~12 percent reduction. Displacement is 0.126 to 0.975 mm on the 1:0.5 slope, 0.152 to 1.158 mm on the 1:0.3 slope, and represents an increase of 10 to 15%. This is a slightly change in normal proportion and is in good condition in terms of stability. In terms practical the working design, it was confirmed that applying the shear strength estimated by Iso-angle division method derived from the H-B failure criterion as a universal shear strength for a good continuum rock mass slope was also able to produce stable and economic results. The procedure for stability analysis using LEM (Limit Equilibrium Analysis Method) and FEM (Finite Element Analysis Method) will also be practical in the rock slope where is not distributed fault. The study was conducted by selecting the slope of study area as a good rock condition, establishing a verification for which it can be applied universal to a various rock conditions will be a research subject later on.
Kim, D.H.;Kim, Y.B.;Koo, H.J.;Baek, H.J.;Lee, S.B.;Hong, E.K.;Kim, S.K.;Chang, K.J.
Journal of Practical Agriculture & Fisheries Research
/
v.23
no.2
/
pp.63-70
/
2021
In order to compare and investigate the growth rates of each of the various soils, the soil mixing ratios were varied to four soils (Pitmos, Pearlite, Masato, General Soil, and Cocopeat). Ten were selected for each soil ratio and the average length and weight were compared. As a result, in the ratio of No. 1 pitmos 6.5: Perlite 2: Masato 1.5, it was measured as 16.36cm, 0.60g. In the ratio of No. 2 pitmos 10, 13.74cm, 0.41g. In the ratio of No. 3 general clay 10, it was measured as 12.43cm, 0.26g. 4 general clay 8, 0.39g. The growth rate of each soil was measured to be superior to that of other soil growth environments in the ratio of pitmos 6.5: pearlite 2: masato 1.5 soil. For ginseng plant analysis, 30 ginseng plants grown in the average length and weight of each soil at a ratio of 6.5: pearlite 2: masato 1.5 and relatively low-result general soil were selected and analyzed. As a result, 1,040ppm of nitrite nitrogen(NO3-N) was higher in ginseng plants grown in general soil. There was no significant difference in phosphoric acid(P), potassium(K), and magnesium(Mg). Ginseng is characterized by poor growth when it exceeds 300ppm by combining ammonia tae (NH4-N) and nitrate tae (NO3-N) nitrogen. In addition, nitric acid produced in a part of this nitrite makes the pH reaction of the soil acidic, and the nitrite remaining in the soil evaporates into gas.
A turn-buckle inserted between tension members sustaining structural loads in the suspension structure system is a device capable of adjusting the tensile force. However, it is difficult to measure the tensile force that is applied to the tension member with the use of a conventional turn-buckle. So a measurable turn-buckle for tensile force measurement has been developed to improve on such a problem. This study focuses on the prevention of a local yielding as well as the maximization of yielding load mentioned in previous studies. A new type of turn-buckle for the measurement to practical use is suggested over the tentative purpose. For this purpose, the ABAQUS analysis of specimens based on theoretical analysis and tests are carried out. The differences among the results of the theoretical analysis, ABAQUS analysis, and the test were insignificant.
Lee Soo-Bok;Ahn Sang-Man;Choi Seung-Hak;Kim Jeong-Hoon;Lee Yong-Taek
Membrane Journal
/
v.14
no.3
/
pp.258-262
/
2004
Trifluoroethyl methacrylate (TFEMA) is used in the preparation of water-repellant paints and optical fiber clading materials, and is manufactured by esterification reaction of trifluoroethanol (TFEA) and methacrylic acid (MA). To estimate the applicability of a pervaporation membrane for the esterification TFEMA esterification, the basic pervaporation properties for TFEA/water mixture were determined using a commercial poly(vinyl alcohol) membrane (GFT Membrane $Pervap^{\circledR}1005$). The effect of TFEA concentration in feed solution and operating temperature on the pervaporation properties was determined. The total permeation flux decreased with increasing TFEA concentration from 90 to 99 wt%, but the separation factor of TFEA/water showed maximum values at 95 wt% TFEA concentration. With increasing feed temperatures from 50 to 8$0^{\circ}C$, the permeation flux and separation factor increased. Higher separation factors and permeation fluxes were observed at 8$0^{\circ}C$ of feed temperature. This pervaporation performance confirmed that the commercial pervaporation membrane could be successfully applied to esterification of TFEMA.
Chain propagation and chain transfer in anionic polymerization of hexafluoropropylene oxide were investigated under various reaction conditions such as the stabilization of reaction temperature, the amount of hexafluoropropylene solvent, and the feeding rate of hexafluoropropylene oxide monomer. Anionic initiator for the polymerization was synthesized from cesium fluoride and hexafluoropropylene oxide in tetraethyleneglycol dimethylether. It was possible to obtain a high molecular weight poly(HFPO) ($M_w$ 14800) using the anionic initiator in conditions of stabilized reaction temperature, and optimized addition of solvent and monomer feeding (HFP/initiator mole ratio=31.5 and HFPO feeding rate=11.67 g/hr). Otherwise, chain transfer reaction in anionic polymerization was increased. From the results of molecular weight in various reaction conditions, it was found that chain propagation and chain transfer in anionic polymerization of HFPO were very sensitive to reaction conditions.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.