• Journal of the Korean Society of Hazard Mitigation
• /
• v.3 no.1 s.8
• /
• pp.123-131
• /
• 2003

An experiment was carried out to investigate the mechanical behaviour of the circular hollow section reinforced concrete member with internal corrugated steel tube. A specimen, 50cm in diameter and 340cm in length, was made and tested by 3 points bending. The test load was increased slowly (quasi static) to the failure or unacceptable deformation. During the test, lateral displacement at mid point and longitudinal displacement of extreme fiber on compressive and tensile side of the specimen were measured. The measured data were analysed and compared with calculated results for the equivalent member without inserted corrugated steel tube. The comparison shows that the flexural strength and ductility of hollow section reinforced concrete members can be improved by inserting corrugated steel tubes inside.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.16-22
• /
• 2010

Various programs for dynamic simulation of the railway vehicle have advantages and disadvantages. These programs have limitation that cannot express a large deformable body for an wire of the railway vehicle. In this study, a program for dynamic simulation of the railway vehicle is developed. And the rigid, flexible and large deformable body can be simulated using this program. Its reliability is verified by comparison with a commercial program. Also, a wire is considered as the large deformable body and a sliding joint which connects the rigid body to the large deformable body is included. Moreover, as the wheel-rail contact module is added, the dynamic simulation of the railway vehicle can be analyzed using the developed program.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.570-570
• /
• 2012

그래핀(graphene)은 육각형의 탄소원자 한층으로 이루어진 이차원 구조체로써 우수한 물리적, 전기적 특성으로 인해 다양한 분야에서 응요을 위한 연구가 활발히 진행되고 있다. 특히, 그래핀과 금속 나노입자의 복합구조는 수소 저장체, 가스센서, 연료전지, 화학 촉매등의 다양한 분야에서 응용이 가능하다. 현재까지 그래핀/금속나노입자 복합구조의 제작 방법에는 열증발(thermal evaporation), 전기도금법(electrodeposition), 표면 기능화(surface functionalization)를 이용한 방법이 보고되었다. 하지만 이러한 방법은 긴 공정시간이 요구되며, 나노입자의 크기 분포가 넓다는 단점을 지닌다. 본 연구에서는 화학기상증착법을 통해 합성된 그래핀이 전사된 SiO2 (300nm)/Si 기판에 염화기가 포함된 백금 화합물 분산용액을 스핀코팅(spin-coating)하고 MeV 전자빔을 조사하여 Pt/grapheme 복합구조를 형성하였다. 이 방법은 균일한 크기 분포의 나노입자의 형성이 가능하며, 간단하고, 대면적 공정이 가능하며, 다른 방법에 비해 그래핀의 결함형성이 적다는 장점을 지닌다. Pt/grapheme 의 기하학적 구조를 주사전자현미경(scanning electron microscopy)와 투과전자현미경(transimission)을 통해 분석하였고, Pt와 graphene의 일함수(workfunction)의 차이에 의해 야기되는 전하이동에 의한 도핑(doping)현상을 라만 분광기(Raman spectroscopy)와 X-선 광전자 분광기(X-ray photoelectron spectroscopy)를 통해 분석하였다.

• Journal of the Korean Chemical Society
• /
• v.48 no.6
• /
• pp.599-608
• /
• 2004

New two kinds of methacrylate monomers having a benzene ring inserted between spacer and methacryloyl group and the chiral center connected to the terminal of the mesogenic structures were synthesized. In these two series the effects for the formation of the liquid crystals in regard to the length changes of the spacers and mesogenic groups were investigated. The first series did not show any liquid crystalline phases in the intermediate compounds nor in the end products. However, the methacrylates of second series showed the liquid crystalline phases in the intermediate compounds as well as in the final products regardless of the length of the spacers.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.05a
• /
• pp.125-128
• /
• 2010

A pyrotechnic igniter with a relatively simple configuration was developed to secure the stable and reliable ignition of the gas generator in space launch vehicles. It was designed not only to provide a sufficient heat flux for the propellant ignition but also to ensure a structural safety under the conditions of very high temperatures and pressures. The burning tests of the igniters have been performed to decide several design parameters, and consequently the performance tests have proved that the pyrotechnic igniter developed in this study meets the design requirements.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.8 no.1
• /
• pp.231-237
• /
• 2004

Most of the masonry buildings have many structural defects under an earthquake load due to the small tensile force and ductility. In the foreign countries there are many the reinforcing methods of masonry buildings, but the glass fiber sheet reinforcements must be used due to various conditions in Korea. The purpose of this paper is to estimate the seismic capacity of masonry buildings damaged by earthquake and reinforced by Glass Fiber Sheet. On the basis of test results, the maximum base shear force and deformation of the masonry building with GFS were remarkably increased. From the comparison by existing strength equations and test data, the new strength equation of reinforced masonry buildings with GFS was developed.

• Journal of Plant Biotechnology
• /
• v.41 no.2
• /
• pp.89-93
• /
• 2014

Long-term subcultured rose embryogenic calluses, which had been maintained for more than 5 to 6 years since the first embryogenesis from calluses induced from in vitro roots of rose, were identified as potential material for the development of transgenic plants. The first embryogenic calluses from 'Sweet Yellow' and two breeding lines (KR056002 and KR056006) were obtained in 2007 and 2009, respectively. Subsequently, we found that plants regenerated from long-term embryogenic calluses (LEC). Whereas the LEC from 'Sweet Yellow' takes 3 to 4 months to regenerate plants, those of the two breeding lines take 4 to 5 months. This period of time is the same as that taken for plants to regenerate from the first embryogenic callus. New embryogenesis was observed from atypical bodies (ABs) that appeared during the process of long-term subculture. We found that it is possible to use the AB as a material for new embryogenesis.

• Korean Chemical Engineering Research
• /
• v.48 no.1
• /
• pp.75-79
• /
• 2010

The precursor powders with thin wall structure were prepared by spray pyrolysis from the spray solution with ethylenediaminetetraacetic acid, citric acid and $NH_4Cl$ flux. The $BaMgAl_{10}O_{17}:Eu$ phosphor powders formed from the spray solution without organic additives and flux material had sizes of $1{\sim}5{\mu}m$ and hollow structure with high thickness at post-treatment temperature of $1,200^{\circ}C$. However, $BaMgAl_{10}O_{17}:Eu$ phosphor powders formed from the spray solution with ethylenediaminetetraacetic acid, citric acid and $NH_4Cl$ flux had fine size and plate-like shape. The mean crystallite sizes of the phosphor powders with fine sizes were 23, 35, and 33 nm when the content of $NH_4Cl$ flux were 0, 6, 35 wt% of phosphor. The photoluminescence intensity of the phosphor powders formed from the spray solution with the optimum amount of $NH_4Cl$ flux as 35 wt% was 215% of that of the phosphor powders formed from the spray solution without flux material.

• Horticultural Science & Technology
• /
• v.32 no.3
• /
• pp.366-374
• /
• 2014

The study was conducted to investigate the possibility that epigenetic DNA methylation causes tree phenotypic variation in autotetraploids through evaluating the phenotypic variation and DNA methylation in autotetraploids occurred spontaneously from diploid trifoliate orange. Chromosome analysis confirmed that fourteen trifoliate orange trees of selected by flow cytometry were tetraploids (2n = 4X = 36) without any aneuploids. Chromomycin A3 staining determined that these trees were all autotetraploid with doubled chromosome set. Tree phenotypes, such as tree height and width, branching number, length, and angle, internode length, and leaf characteristics, varied in the autotetraploids. Chlorophyll indices were diverse in the autotetraploids, but photosynthetic rates were not significantly different. In addition, a wide range of variation was observed in stomatal density and guard cell length. Analysis of global cytosine DNA methylation showed that there was a variation of the methylation level in autotetraploids. More than half of 14 autotetraploids had at least 2 times higher methylation level than diploid trifoliate orange. The results indicate that tree phenotypic variation in autotetraploids might be related to global DNA methylation for reducing gene redundancy.

• Journal of the Korean Ceramic Society
• /
• v.41 no.11
• /
• pp.797-803
• /
• 2004

The heat generation tests of SiC and MO$_2$ samples by use of a microwave heating system were carried out and UO$_2$+5 wt% CeO$_2$ pellets were sintered in a microwave furnace in an oxidizing atmosphere, by taking into account the characteristics of the microwave heating obtained from the heat generation tests. The characteristics of pellets sintered in a microwave furnace were analysed and compared with those of the pellets sintered in a conventional electrical furnace. The temperature of MO$_2$ pellets with microwave heating increased quickly with input power and the variation of output power depended on the reaction characteristics of SiC and MO$_2$ with microwave. The sintered density of UO$_2$+5wt% CeO$_2$ pellets sintered in the microwave furnace was lower about 2% T.D. than that of the pellets sintered in an electrical furnace with sintering parameters. The microstructure of pellets sintered in microwave furnace has a broader pore distribution but has a larger grain size than that of the pellets sintered in the electrical furnace.