• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.39 no.5
• /
• pp.425-433
• /
• 2015

In this paper, we have numerically investigated two-dimensional dielectrophoretic (DEP) motions of a single particle suspended freely in a viscous fluid, interacting with a nearby nonconducting planar wall, under an externally applied uniform direct-current electric field. Particularly, we solve the Maxwell equation with a large sharp jump in the electric conductivity at the particle-fluid interface and then integrate the Maxwell stress tensor to compute the DEP force on the particle. Results show that, under an electric field parallel to the wall, one particle is always repelled to move far away from the wall and the motion depends strongly on the particle-wall spacing and the particle conductivity. The motion strength vanishes when the particle is as conductive as the fluid and increases as the conductivity deviates further from that of the fluid.

• Tunnel and Underground Space
• /
• v.21 no.3
• /
• pp.174-180
• /
• 2011

An anisotropic version of Mohr-Coulomb failure criterion is proposed in order to provide a strength criterion for transversely isotropic rock. The concept of fabric tensor introduced by Pietruszczak & Mroz (2001) is employed to define the friction angle and cohesion as scalar functions of the fabric tensors. The anisotroy in these two strength parameters are calculated in association with the consideration of the relative rotation between the principal stress coordinate and the principal material triad. The critical plane on which the anisotropic function maximized is found by an optimization technique based on the Lagrange multiplier method. To demonstrate the performance of the anisotropic failure criterion, conventional triaxial tests on the samples having various inclinations of weakness plane are simulated and the resulting triaxial strength and dip angle of failure plane are discussed.

• The Korean Journal of Rheology
• /
• v.6 no.2
• /
• pp.104-118
• /
• 1994

단섬유 보강 플래스틱 재료의 사출성형 충전공정에서 금형재의 유동장이 섬유 배향 상태를 형성하는데 중요한 역할을 할 뿐만 아니라 섬유의 배향상태가 역으로 유동장에 영향 을 미친다. 충전유동과 섬유 배향의 연계해석을 위하여 단섬유에 의한 추가적인 응력을 포 함하는 Dinh과 Armstrong의 이방성 구성방정식을 충전유동의 해석에 도입하였다. 평명방향 으로의 속도구배에 의한 응력을 고려하여 새롭게 유도된 압력 지배방정식과 에너지방정식을 유한요소법과 유한차분법을 이용하여 풀고 동시에 2차배향텐서의 변화방정식을 4차 Runge-kutta 방법을 이용하여 풀었다. 절점 게이트 주변의 확장유동영역과 라인게이트를 통한 수축유동영역에서 평면방향으로의 속도구배에 의한 응력이 유동장에 미치는 영향을 고 찰하였다. 확장유동영역에서는 평면방향으로의 속도구배에 의한 영향이 추가적인 유량으로 나타나면서 주어진 유량조건하에서 평면방향으로의 속도구배에 의한 응력을 고려하지 않은 경우보다 작은 압력구배를 나타냈다. 수축유동영역에서는 위와 반대의 결과를 보였다. 이러 한 경향은 섬유의 부피분율이증가하거나 모양비가 커짐에 따라 증가한다.

• The Korean Journal of Rheology
• /
• v.8 no.2
• /
• pp.78-91
• /
• 1996

단섬유 보강 플라스틱 복합재료에 사출성형에서 섬유배향은 금형 충전 공정 중의 유동장에 의해 결정되고 섬유의 배향 상태는 역으로 유동장에 영향을 미친다. 단섬유에 의 한 추가적인 응력을 포함하는 Dinh과 Armstrong의 이방성 구성방정식을 충전유동과 섬유 배향의 연계해석에 도입하였다. 충전유동의 해석은 새로운 압력 지배방정식과 에너지 방정 식을 유한요소법과 유한차분법을 이용하여 풀고 동시에 2차 배향 텐서의 변화방정식을 4차 Runge-kutta 방법으로 풀었다. 섬유의 배향상태를 구한 후에 일방향성 복합재료의 Halpin-Tsai 식과 배향 평균모델을 도입하여 사풀성형품의 이방성 기계적 성질이 예측되었 다. 직사각형 캐비티에서 수치해석결과를 실험결과와 비교하였다. 섬유배향과 유동과의 상호 연계작용을 특히 게이트 근처에서 섬유배향에 영향을 미치며 수치해석 결과는 벽면 근처에 서 유동방향으로 배향하는 shell층을 과대 예측함을 알수 있었는데 이는 배향 텐서 변화 방 정식의 최종근사에서 기인하는 오차로 판단된다. 수정된 복합최종 근사를 바탕으로 예측된 이방성 기계적 성질이 기존의 복합최종 근사에 기초한 예측보다 실험 결과에 정량적으로 보 다 잘 일치하였다.

• Composites Research
• /
• v.14 no.6
• /
• pp.16-23
• /
• 2001

Analysis of mechanical behavior for a pultruded-wound hollow rod is presented. For this purpose, the pultruded-wound hollow rod is manufactured by the new winder attached to the conventional pultrusion system. And the conventional pultrusion process is newly altered to manufacture pultruded-wound specimens. A computer program, POST II, is modified to perform this study, In the nonlinear finite element formulation, the updated Lagrangian description method based on the second Piolar-Kirchhoff stress tensor and the Green strain tensor are used. For the finite element modeling of the composite hollow rod, the eight-node degenerated shell element is utilized. In order to estimate the failure, the maximum stress criterion is adopted to the averaged stress in the each layer of the finite elements. As numerical examples, the behavior of glass/up composite hollow rod is investigated from the initial loading to the final collapse. Present finite element results considering stiffness degradation and stress unload due to failure shows excellent agreement with experiments in the ultimate load, failure and deformations.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.771-776
• /
• 2000

Fine grid calculations are reported for the developing turbulent flow in a straight duct and a curved duct of square cross-section with a radius of curvature to hydraulic diameter ratio ${\delta}=R_c/H_H=3.357$ and a bend angle of 180 deg. A sequence of modeling refinements is introduced; the replacement of wall function by a fine mesh across the sublayer and a low Reynolds number second moment closure up to the near wall sublayer in which the non-linear return to isotropy model and the cubic-quasi-isotropy model for the pressure strain are adopted; and the introduction of a multiple source model for the exact dissipation rate equation. Each refinement is shown to lead to an appreciable improvement in the agreement between measurement and computation.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1061-1062
• /
• 2011

본 논문에서는 매입형 영구자석 동기전동기(IPMSM) 전자기력 특성 해석을 수행하였다. 전동기에서 발생하는 전자기력(Electromagnetic force)은 기기의 성능 뿐만 아니라 소음 및 진동을 유발하며 전기기기의 stress를 야기한다. 본 논문에서는 전자기력 특성을 맥스웰 응력 텐서법를 이용하여 각 노드에서 발생하는 전자기력 분포에 대해 분석하였다. 그리고 매입형 영구자석 전동기의 운전상태 및 구조파트 중 고정자 치에서 발생하는 전자기력 분포에 대해 분석하였다.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.4
• /
• pp.725-734
• /
• 2009

Maxwell stress tensor is one of the methods which are generally used for electromagnetic force calculation. In this paper, it is presented that Maxwell stress tensor T and n${\cdot}$T have no physical meaning and therefore should not be used as sources of mechanical force for deformations or dynamics. The divergence of Maxwell stress tensor ${\nabla}{\cdot}T$ is the one which can acquire a physical identity and is electromagnetic body force density by an action at a distance like a gravity. This result can be derived from the principle of power balance, and also verified by some thought experiments. The virtual air-gap approach is proposed as a valid solution for the calculation of the body force.

• Composites Research
• /
• v.25 no.4
• /
• pp.117-125
• /
• 2012

Warpage of the film insert molded (FIM) part is caused by an asymmetric residual stress distribution. Asymmetric residual stress and temperature distribution is generated by the retarded heat transfer in the perpendicular direction to the attached film surface. Since warpage was not prevented by controlling injection molding conditions, glass fiber (GF) filled composites were employed as substrates for film insert molding to minimize the warpage. Distribution of short GFs was evaluated by using micro-CT equipment. Proper models for micro mechanics, anisotropic thermal expansion coefficients, and closure approximation should be selected in order to calculate fiber orientation tensor and warpage of the FIM part with the composite substrate. After six kinds of micro mechanics models, three models of the thermal expansion coefficient and five models of the closure approximation had been considered, the Mori-Tanaka model, the Rosen and Hashin model, and the third orthotropic closure approximation were selected in this study. The numerically predicted results on fiber orientation tensor and warpage were in good agreement with experimental results and effects of GF reinforcement on warpage of the FIM composite specimen were identified by the numerical results.

• Journal of the Korean Society of Hazard Mitigation
• /
• v.1 no.3 s.3
• /
• pp.123-136
• /
• 2001

The purpose of application of moment tensor inversion method is to determine source parameters, such as, focal mechanism, seismic moment and source depth. This paper presents results of focal mechanism solutions of 14 recent events with magnitudes ranging from M3.3 to M4.8 by using moment tensor inversion method called TDMT_INV. The strike of faults is in the direction of NE-SW and NW-SE with the movement of strike-slip or strike-slip of minor reverse component. The compressional axis of the stress field is predominantly E-W or ENE-WSW except for some faults, which are distributed at Ryongnam Massif and Wonsan, they have a compressional axis of N-S or NNW-SSE.