• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.24 no.3
• /
• pp.159-165
• /
• 2012

In this study, a series of deposition tests have been performed using an annular flume and depositional parameters of natural cohesive sediments have been estimated domestically for the first time. The natural cohesive sediments for deposition tests have been collected from Kwangyang Bay and total 18 deposition tests have been carried out on different bed shear stress respectively but with the same initial concentration. Test results for natural cohesive sediments of Kwangyang bay show that minimum bed shear stress ${\tau}_{bmin}$, standard deviation ${\sigma}_1$, and time scale parameter $({\tau}_b^*-1)_{50}$ are $0.11N/m^2$, 0.68 and 0.85, respectively. Through the comparison with results of previous studies for other sediments, the results of this study are shown to be good enough to verify.

• Journal of the Korean Geosynthetics Society
• /
• v.12 no.3
• /
• pp.55-64
• /
• 2013

In this study, a series of the isotropic compression-expansion tests and the Undrained triaxial tests were performed on low-plastic silt of Pocheon stone sludge. Using the tests results the characteristic of the parameters of Lade's single hardening constitutive model were investigated. We also observed that predicted values from the Lade's single hardening constitutive model were well consistent with the observed data. In experimental results the deviator stress showed the work hardening behaviour after reaching its yield stress. Therefore practically useful failure criterion for low-plastic silt were required. The stress-strain behavior predicted by 11 soil parameters are compared with the results obtained 9 parameters by correlation between h and ${\eta}_1$ and constant ${\alpha}$. They are poor matched each other.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.19 no.2
• /
• pp.84-91
• /
• 2015

In this paper, to overcome disadvantages of existing lining boards, the parametric studies to evaluate safety and verify performance of newly suggested lining boards was performed. Since the calculated stresses of steel plates are lower than the allowable stress for considered all analytical variables, end reinforcement locations, and crane rail loads, it can be concluded that the suggested lining board is structurally safe. Where, "$3,000{\times}2,000{\times}6t$" was select to be optimized cross-section and the reinforcement from the end to 200mm to the internal direction looks like the best case. In addition, the suggested lining board is economical since the steel amount per unit area compared to existing lining board is reduced by 36% and it can apply to the lining structural system of subway and underpass since construction speed is past due to the less installation number of lining boards.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05b
• /
• pp.377-382
• /
• 1998

재료 조사시험용 계장캡슐은 하나로(Hi-Flux Advanced Neutron Application Reactor : HANARO) 를 이용하는 조사시설중의 하나이다. 캡슐 내부에 있는 열매체는 다공 원통구조물로 고려되며, 다양한 형태와 크기를 갖는 조사시험용 시편이 각 단에 삽입된다. 조사시험에 대한 사용자의 요구조건을 효율적으로 충족시키기 위해서는 캡슐 열매체에 대한 여러 역학적인 특성을 파악하여 설계 및 제작할 필요가 있다. 따라서 계장 캡슐 설계의 초기단계로서 다양한 기하학적인 설계변수를 갖는 다공 캡슐 열매체의 구조적 특성을 파악하기 위한 연구를 수행하였다. 조사 분위기인 하중상태에서의 다공 구조물에 대한 구조응력해석을 수행하여 다공 매개변수에 따른 응력 및 변위 등을 고찰하였고, 구조물의 건전성을 평가하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.29 no.6A
• /
• pp.661-669
• /
• 2009

Various kinds of shear connectors such as headed stud, channel, perforated steel plate and others are commonly used to transfer stress and conduct composite performance in steel concrete composite structures, and many researches have been conducted to improve the characteristics of different types of shear connectors. It is focused in this study on the pull-out and pushout performance of steel pipe pile cap with the open type perfobond for the composite connection to the spread footing. A parameter analysis was conducted, using ABAQUS, a nonlinear finite element analysis program, to obtain data for determining the characteristics of the structure and to allow various parametric analyses of steel pipe cap with the open perfobond.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.16 no.5
• /
• pp.487-495
• /
• 2014

In this study, in order to suggest the design method for supports in the room-and-pillar underground structure, the case study was carried out. In the case study, shape of rock pillar and room was mainly considered. From the analysis, a displacement at the roof, the maximum principle stress and plastic state were examined. To optimize variables in the case study, cases from the Seoul metro station were analyzed, then a target depth of the underground structure and ground conditions were determined. And the height of rock pillar and room were chosen from the assumed purpose of underground space, i.e. living/office and warehouse. Total cases of analysis was 180 cases including 3 types of ground condition, 5 types of rock pillar and 6 types of roof span. It is expected that results from analysis can be used to determine the installation of support in room-and-pillar underground structure with stability, utilization efficiency of underground space and applicability of vehicles.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.12 no.2
• /
• pp.191-203
• /
• 1992

This paper dealt with the statistical values including mean, standard deviation, variance and coefficient of variation for 14 soil parameters available of Lade's double work-hardening model in order to predict the behaviour of granular soil. 27 sets of all 14 parameters for Baekma river sand were determined by regression using raw data acquired from 12 isotropic compression tests and 9 triaxial compression tests with the variation of confining pressure of 1, 2, and $4kg/cm^2$ respectively 3 times performed during this study. The characteristics of each parameters were investigated. By determining the range of the upper and lower bound dependent on the increase and decrease of the standard deviation from mean value of parameters, sensitivity of all the parameters was scrutinized, by which in turn the influence of experimental error generated inevitably during tests on the determination of soil parameters was also examined.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1A
• /
• pp.45-54
• /
• 2006

To obtain realistic stress-strain relation in concrete, it is necessary to improve the constitutive model for creep and shrinkage of concrete. This study is made up with predicting model of creep using rheological approach and mathematical development which is solution for phenomenon of concrete creep. Long-term deformation components are combined based on traditional 4-parameters model. Creep deformation is obtained adequately using 4-parameters determined by considering aging effect and microprestress among gels. And coefficient of effective viscosity is able to represent both basic creep and total creep included drying creep. This study attempt to establish mathematical model considering effects of aging, hydration, and variations of pore humidity. It can predict both basic creep and total creep. Values of result between prediction and experiment have greater than correlation factor 99%. Additionally experimental results report bad consentaneity with highway design specification adopting FIB MC 90. Rather than those are similar to FIB MC 90 rev.99.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.16 no.2
• /
• pp.165-172
• /
• 2003

In this study, a new and efficient harmonic axisymmetric shell element for static and dynamic analysis Is proposed. The present element considering shear strain is based on a modified mixed variational principle in which the independent unknowns are only the Quantities prescribable at the shell edges. Unlike existing hybrid-mixed axisymmetric shell elements, the present element introduces additional nodeless degrees for displacement field Interpolation In order to enhance the numerical performance. The stress parameters are eliminated by the stationary condition and the nodeless degrees are condensed out by the Guyan reduction. Through several numerical examples, the hybrid-miked shell element with the additional nodeless degrees and the consistent stress parameters is shown to be efficient and yield very accurate results for static and vibration analysis.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.12 no.2
• /
• pp.161-169
• /
• 1999

이방성체의 평면내 직선균열에 대한 균열선단부근의 응력과 변위의 분포는 어떠한 균열체의 형상 및 하중조건에 대해서도 응력확대계수라는 하나의 매개변수로서 나타낼 수 있다고 하는 것이 파괴역학에서 보편화되어 있다. 그러나 많은 경우에 있어서 급수전개식의 이어지는 항은 정량적으로 중요하다. 따라서 본 연구에서는 이러한 항을 유도하고 이것이 균열진전방향에 미치는 영향에 대하여 검초하였다. 이를 위하여 단축하중을 받는 직방성균열체의 해석을 수행하며 재료는 균질이방성체라고 가정하였다. 급수전개식에서 2차항의 영향을 고려하기 위하여 균열선단에서의 응력의 분포를 재해석하였으며, 2차항의 사용은 정확한 균열진전방향의 결정을 위해서 매우 중요함을 보였다. 초기균열진전각도의 결정을 위해서 수직응력비이론을 적용하였다.