• Journal of Advanced Marine Engineering and Technology
• /
• v.34 no.8
• /
• pp.1094-1099
• /
• 2010

Three dimensional laminar flows are numerically simulated around the submerged spheres. The finite volume based Navier-Stokes equations with unstructured grids are solved to make clear the hydrodynamic phenomena near and far away from the body. Reviews are made on with the vorticity, velocity, dynamic pressure, residuals, drags, etc. The Reynolds numbers under consideration are 425, 300, 250 and 100. In case of small spacing between spheres, the flow is more stable than that past a single sphere. According to the analysis, the flow past two spheres is found to be unstable as the spacing becomes larger. The rear sphere shows the deduction of stagnation pressure, which results in the decrease of the resistance. The predicted drag coefficients verify that the present numerical calculation is reasonable.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.42 no.9
• /
• pp.723-730
• /
• 2014

Experimental study for supersonic co-flowing fluidic thrust vectoring control utilizing the secondary flow is performed. The characteristics of the thrust vectoring of two dimensional supersonic flow (Mach 2.0) are studied by Schlieren flow visualization and highly-accurate multi-component force measurements using the load cells. It is observed that the thrust deflection angle initially decreases and increases again forming a V-shaped variation as the pressure of the secondary flow increases. Characteristics of the performance coefficients of the system are also studied, and the detailed operating conditions for higher performance of the technique are suggested.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.7
• /
• pp.689-695
• /
• 2012

The friction factor in a rod bundle and the loss coefficient at a spacer grid were examined. As a test section, 25 smooth rods, 9.5 mm in diameter and 2000 mm in length, were prepared and installed in a $5{\times}5$ square array in a square channel. In this case, the P/D (Pitch-to-Diameter ratio) was 1.35. In this work, plain (i.e., no mixing vanes), split-vane, and hybrid-vane spacer grids were tested. In a bare rod bundle (i.e., no spacer grid), the measured friction factors were in good agreement with the previous correlations. Among the spacer grids tested, the hybrid-vane spacer grid presented the largest friction factor in the rod bundle and loss coefficient. This may be because of the flow pattern change induced by large relative plugging of the flow cross section and mixing vane geometry. At Re=$5{\times}10^5$, the predicted loss coefficients of plain, splitvane, and hybrid-vane spacer grids were approximately 0.79, 0.80, and 0.88, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.6
• /
• pp.650-655
• /
• 2016

In this study, a computational simulation of the internal flow characteristics was carried out for a Urea-SCR Injector. A single hole swirl injector with a swirl disk and slanted nozzle was used in this simulation. The maximum needle lift and opening velocity were selected as the design parameters. To analyze the unsteady internal flow characteristics of the Urea-SCR injector, the moving grid technique was applied to simulate the delicate needle movement. According to the simulation results, the injected mass flow rate from the Urea-SCR injector decreased with increasing needle opening velocity and maximum needle lift. This is because the Urea-solution tends to fill the empty space that the needle previously occupied. The swirl flow is decreased as the flow goes through the injector nozzle, because of the friction with the nozzle wall. Also, during the maximum needle lift period, the swirl coefficient and mean swirl coefficient increase with increasing needle lift. The results of this study may be used as the basic design data of related injectors.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.17 no.1
• /
• pp.9-17
• /
• 2013

A considerable deal of work has been carried out to get an insight into the gas-solid suspension flows and to specify the particle motion and its influence on the gas flow field. In this paper an attempt is made to develop an analytical model to study the effect of nozzle inlet/exit pressure ratio, particle/gas loading and the particle diameter effect on gas-solid suspension flow. The effect of the particle/gas loading on the mass flow, Mach number, thrust coefficient and static pressure variation through the nozzle is analyzed. The results obtained show that the presence of particles seems to reduce the strength of the shock wave. It is also found that smaller the particle diameter is, bigger will be the velocity as bigger particle will have larger slip velocity. The suspension flow of smaller diameter particles has almost same trend as that of single phase flow with ideal gas as working fluid. Depending on the ambient pressure, the thrust coefficient is found to be higher for larger particle/gas loading or back pressure ratio.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.47 no.1
• /
• pp.17-25
• /
• 2019

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.3
• /
• pp.285-292
• /
• 2013

The purpose of this research is to investigate how the boundary layer separation caused by a tripping wire installed in front of the flat plate affects the transition from laminar to turbulent flow, and consequently mass transfer. A naphthalene sublimation technique is used to measure the local mass transfer coefficients on the flat plate, and two boundary conditions for the developed and developing flow are considered to evaluate the effects of the flow boundary. The local mass transfer data for a flat plate with a tripping wire are compared with the data for a flat plate without a tripping wire. The variation trends of the local heat transfer coefficients for the plates with and without the tripping wire are similar to each other in the case of the developing flow, but are quite different for the developed flow. The average Sherwood number for the flat plate with a tripping wire is much higher than that without a tripping wire because of the boundary layer separation.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.7
• /
• pp.90-97
• /
• 2002

Wall slip models are essential to the study of nonequilibrium gas transport in rarefied and microscale condition that can be found in gas flows associated with aerospace vehicle, propulsion system, and MEMS. The Maxwell slip model has been used for this type of problem, but it has difficulty in defining the so-called accommodation coefficient and has not been very effective in numerical implementation. In the present study, on the basis of Langmuir's theory of the adsorption of gases on metals, a physical slip model is developed. The concept of the accommodation coefficient and the difference of gas particles are clearly explained in the new model. It turned out that the Langmuir model recovers the Maxwell model in the first-order approximation. The new models are also applied to various situations including internal flow in a microchannel. Issues of validation of models are treated by comparing analytic results with experiment.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.35 no.8
• /
• pp.847-853
• /
• 2011

Filiform hairs that respond to movements of the surrounding medium are the mechanoreceptors commonly found in arthropods and vertebrates. The hairs function as a sensory system for perceiving information produced by prey, predators, or conspecifics. A mathematical model is proposed, and the parametric analyses for the response of artificial filiform hair are conducted to design and predict the performance of a microfabricated device. The results for the Cytop hair, one of the most popular polymer optical fibers (POFs), show that the fundamental mode has a dominant effect on the hair behavior in an oscillating medium flow. The dynamic behavior of sensory hair is also dependent on the physical dimensions such as length and diameter. It is found that the artificial hair with a high elastic modulus does not show a resonance in the biologically important frequency range.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.383-387
• /
• 2017

A three dimensional numerical analysis has been conducted to analyze the effects of a pipe angle, connecting a combustion chamber and a pintle nozzle, and pintle position on pintle nozzle performance. The compressibility correction of $k-{\omega}$ SST turbulent model was implemented to precisely predict the characteristics of complex flow structures inside a supersonic pintle nozzle. Due to an 3-D asymmetric pintle nozzle configuration, complex helical flow streamlines and large flow separations were observed, which resulting in significant nozzle performance losses. As the angle of connection-tube decreases, the coefficient of performance increases and Since the flow structures are evidently changed to the pintle stroke position, the performance characteristics was analyzed.