• Tunnel and Underground Space
• /
• v.17 no.6
• /
• pp.475-483
• /
• 2007

With increasing demand for LNG as energy resources and need for $CO_2$ sequestration as greenhouse gas, more storage facilities are required in Korea. Due to the recent acute safety concerns and land shortage, storage facilities tend to be located underground. In design and construction of underground storage for low and high temperature materials, besides their mechanical characteristics, the thermal characteristics of rock under temperature variation should be understood. In this study, laboratory experiments for the measurement of the thermal expansion coefficient of rock were performed using strain gauge in consideration of the particle size of mineral and experiment temperature range. Experiment results show that thermal expansion coefficient decreased as the temperature decreases. In addition, linear thermal expansion coefficient was developed for typical Korean rocks such as granite. The results of this study can be utilized for the evaluation of thermal propagation in rock mass and the thermo-mechanical stability of underground facilities.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.46 no.5
• /
• pp.44-51
• /
• 2009

In this paper, an air conditioner peak power control system using electric power line communication has been developed. The air conditioner power control system using RS-485 communication method is hard to install on the existing buildings due to difficulty in cabling, and the system using wireless communication methods has a weak point of not being able to be used in close space, while the developed system has its own advantages of overcoming the above mentioned obstacles. In addition, the system is extended to support not only single-phase electricity system but also three-phase four-wire electricity system, and therefore can be installed anywhere in the domestic environment. The system also has enhanced the ease of deployment, operational stability and economical efficiency by compact circuit design. Considering the current state requiring the energy sayings, the system would greatly contribute to the widespread use of the air conditioner power control system. The superiority in the performance and stability of the system has been proved by the design verification of each component such as remote air conditioner controller, electric power line gateway and so on, and the field test of the whole system.

• Journal of IKEEE
• /
• v.21 no.2
• /
• pp.105-114
• /
• 2017

This paper proposes a design method of an LCL-filter for grid-tied three-level inverter systems. The demand for three-phase PWM inverters in applications such as wind or solar power generation systems has been increase in recent years. To reduce harmonic components caused by switching operation, such inverters are connected to the grid via an LCL filter. Although there are research results for designing LCL-filter, the modulation method should be fully considered to make the filter perform desired cancellation ability with minimized size. This paper presents the design methodology for an LCL-filter that is optimized for SVM switching operations. The simulation and experimental results verify the validity of the LCL-filter designed with proposed method in this paper.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.9 no.4
• /
• pp.80-89
• /
• 2010

Most of the discussed power efficient routing algorithms, such as LEACH, PEDAP and etc., assume that a base station has infinite resources and there is no traffic limit. However, these assumptions cannot be applied to typical wireless sensor network environments, especially a small sensor network using a normal node as the base station. Moreover, many studies on the wireless sensor networks have not been considering the reverse transmission scheme which transmits data from a sink node to the normal nodes. We propose a bitarray-based reverse routing method which is a power efficient routing algorithm for the wireless sensor networks. The proposed method can be easily implemented by using the tree-based routing scheme and can be worked well with the small memory size for the address of sensor nodes. The experimental result shows that the amount of message transmission of the proposed bitarray-based reverse routing method can be reduced about 61.3% or more compared to the previous methods.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.27 no.6
• /
• pp.328-336
• /
• 2015

Currently, 22% of the total energy consumption of buildings in Korea is used for lighting. Light-shelves have garnered attention as a way to reduce consumption, but there are few studies on the types of curve and curvature, which limits the improvement of light-shelf performance and its design. This study constructed a test bed of actual residential types to evaluate the performance. Outcomes of light usage, according to variables of light-shelves, were used as indicators of performance evaluation. The results are as follows:1) Performance evaluation was conducted on flat-type light-shelves to verify performance of curvature-shelves, which are movable with a width of 200 mm, and the most ideal angle and specification per solar term are calculated. 2) The (-) shaped curvature contributed to a reduction in energy consumption and an improvement of evenness. 3) In case of light-shelves with (-) shaped curvature, an increased angle not exceeding $80^{\circ}$ of the arc contributed to an improvement of light penetration. 4) Appropriate specifications of curved light-shelves include movable types with widths of 200 mm, and angle ranges of $20^{\circ}{\sim}60^{\circ}$. 5) Light energy consumption of a movable light-shelf with curvature and width of 200 mm were reduced by 17% and 7.8% compared to a $0^{\circ}$ fixed and a movable light-shelf, respectively.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.61-64
• /
• 2008

A combination of CFT column and RC flat plate without formworks is very effectively rapid constructions. This paper verified the lateral resisting capacity of CFT column-RC flat plate exterior connection in comparison with general RC column-flat plate connection and detected moment capacity and ductility capacity of connection according to moment-displacement ratio. We made and tested specimens which have different variables respectively and as a result derive a following conclusion. In CFT-E2 specimen a critical section was extended and maximum moment increased 20% respectively in comparison to general RC column specimen. In BME and CFT-E1 specimens generally shear governed behaviors and CFT-E2 specimen complemented with seismic band, flexure behavior region of slab was extended and also ductility ratio and energy absorptance increased.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.15 no.5
• /
• pp.133-138
• /
• 2015

In this paper, we propose a method for improving the lifetime of the sensor network SEP through the wireless sensor network divided into two spaces by reducing the transmission distance of the cluster head in the layer in the distance. With reference to the position information of the node, the base station divides the layer based on the midpoint of the nearest node and the furthest distance away from the base station node. And the cluster head in the outer layer far from the base station is transmitted the data to the base station via the cluster head in the inner layer base station to transmit data. That is, we are proposed the layered SEP by reducing the transmission distance of the cluster head in the outer layer for the energy consumption to a minimum. The proposed algorithm is verified by comparison with the existing SEP.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.18 no.1
• /
• pp.29-35
• /
• 2018

Safety accidents are frequently occurring in day care centers in recent years. The number of types of safety accidents is bumping into, falling, burning, school bus accident, insertion... etc., and the number of children who have died due to such accidents is increasing steadily every year. Therefore, it is urgent to prevent accidents at day care centers. IoT (Internet of Things) is managed by connecting various sensors and related products from the living space to the Internet in order to prevent them from being dangerous. In particular, IoT products can be automatically controlled by smart phones and sensors anytime and anywhere, thus saving energy, time, convenience and prompt accuracy. This paper proposes a research model to prevent and respond to disasters by using SK LoRa communication network and Arduino, which are Internet access networks for building disaster management in schools, kindergartens and day care centers. And various sensors needed for building disaster management express various safety states in the building and suggests a system that can control the residential environment by transmitting and receiving data to smart phone.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.12B
• /
• pp.1359-1370
• /
• 2009

In wireless sensor networks, data dissemination is based on data-centric routing that well matches the publish/subscribe communication paradigm. The publish/subscribe paradigm requires decoupling properties: space, time, and synchronization decoupling. For large-scale applications, the three decoupling properties provide scalability and robust communication. However, existing data dissemination schemes for wireless sensor networks do not achieve full decoupling. Therefore, we propose a novel data dissemination scheme that fully accomplishes the three decoupling, called ARBIETER. ARBITER constructs an independent network structure as a logical software bus. Information interworking between publishers and subscribers is indirectly and asynchronously performed via the network structure. ARBITER also manages storage and mapping of queries and data on the structure because of supporting different time connection of publishers and subscribers. Our simulation proves ARBITER show better performance in terms of scalability, network robustness, data responsibility, mobility support, and energy efficiency.

• Spatial Information Research
• /
• v.19 no.3
• /
• pp.11-22
• /
• 2011

It is usual for the carbon dioxide emission to be calculated by official energy consumption statistics produced from a number of specialized industrial process such as refinery, power plant etc. The aim of this research was to evaluate potential of cadastral system in monitoring carbon dioxide emitted from land use. An empirical study for a cadastral category was conducted to demonstrate how a on-site measurement can be used to assist in estimating the carbon dioxide emission in terms of land use specific settings. The cadastral category based analysis made it possible to identify area-wide patterns of carbon dioxide emission, which cannot be acquired by traditional Government statistics. It was possible to identify successively increasing trends in the human-related parcels such as housing land while decreasing trends of carbon dioxide in sink parcels(eg. forest). The results indicate that the cadastral parcel could be used not only as a tool to monitor carbon dioxide emission, but also as an evidence to restrict initiation of development activities causing negative influence to carbon dioxide emission such as road construction. As a result, the research findings have established the new concept of "carbon dioxide emission monitoring based on cadastral category", proposed as an initial aim of this paper.