• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.34 no.6
• /
• pp.10-17
• /
• 2006

NACA23012익형에 대하여 synthetic jet을 이용하여 박리 제어를 수행하였다. 공력특성의 향상을 위해 앞전 droop과 plain flap의 박리 부근에 synthetic jet을 위치시켰다. 고 받음각에서 앞전 박리의 발생으로 인한 실속을 앞전 droop의 작동과 이때 발생하는 앞전 박리를 synthetic jet으로 효과적으로 지연시킬 수 있고, 또한 실속 특성을 개선 할 수 있음을 확인하였다. 양력의 향상을 위하여 plain flap을 장착하였고, 이때 발생하는 박리를 synthetic jet으로 지연시켜 제어면의 작동 효율을 증가 시킬 수 있음을 확인하였다. 앞전 droop과 plain flap으로 구성된 간단한 고양력 장치에 발생하는 박리를 synthetic jet으로 제어함으로 실속을 지연시킴과 동시에 실속 특성을 향상시키고, 최대 양력의 증가로 fowler flap에 버금가는 공력특성을 확보할 수 있음을 확인하였다.

• Proceeding of EDISON Challenge
• /
• 2016.03a
• /
• pp.628-631
• /
• 2016

본 연구에서는 플라잉디스크의 윗면 곡률과 끝단두께에 따른 공력특성의 변화 및 유동 흐름을 EDISON_CFD를 통해 해석하고자 한다. 플라잉디스크는 받음각이 증가할수록 윗면 표면에서는 박리 거품이 발생하게 되고 아랫면에서 윗면으로 올라 갈려는 유동의 흐름이 발생하게 되어 뒷전과 후류에서 거대한 박리 거품이 발생하게 되어 공력특성 및 유동흐름에 큰 변화를 주게 된다. 총 5가지의 형상에 대해서 받음각을 $0^{\circ}{\sim}25^{\circ}$까지 마하수 0.0588, 해석모델은 KFLOW에서 k-w SST를 레이놀즈수 $3.78{\times}10^5$을 조건으로 각 형상의 공력특성과 유동의 흐름의 비교를 분석하였다. 그 결과 윗면의 곡률이 증가 할수록 앞전박리가 활발해지고, 끝단두께가 두꺼워 질수록 뒷전박리가 활발해진다. 이로 인해 곡률은 완만할수록 두께는 얇을수록 양력계수와 실속각을 증가 시킬 수 있다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.6
• /
• pp.38-45
• /
• 2016

A study was conducted on the effect of leading edge location for the performance characteristics of a centrifugal compressor impeller. Five impellers with different leading edge location were selected for numerical analysis. The impeller with leading edge located 10% away from the inlet about meridional distance from entrance to exit showed the best total pressure ratio and efficiency. Also, this case showed relatively uniform flow distribution because of a weak intensity of the separation region at impeller exit. The impeller with leading edge located far from this location showed lowest total pressure ratio and efficiency. Performance of compressor also decreased due to non-uniform flow distribution at impeller exit.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.62-72
• /
• 2004

In this paper. firstly, numerical results were compared with experimental results to verify accuracy of the results. It is found that the numerical results show good agreements with experimental result. Next, computations about flow within blades for design parameters such as radius of the pressure and suction side's curvature and pitch-chord ratio have been performed. It is found that the flow and performance characteristics mainly depend on shocks occurred at the leading edge of blades and the end of nozzle and separations occurred inside the flow passage. And shock of nozzle and separations depend upon area of flow passage and shocks of blade are affected by the number of blades occupied by a nozzle.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.12
• /
• pp.1059-1066
• /
• 2007

An experimental study has been conducted to investigate the flow separation control effects of a blowing jet on an elliptic airfoil at a Reynolds number of 7.84×105 based on the chord length. A blowing jet was obtained by pressing a plenum inside the airfoil and ejecting flow out of a thin jet slot that located in leading edge or trailing edge. The experimental results have shown that the blowing jet had an effect of suppressing the flow separation, resulting in the higher suction pressure distribution and higher normal force. The increase in Cn was more pronounced at higher incidence, whereas the effectiveness of the blowing jet reduced at lower incidences. The leading edge pulsating blowing with 90° was the most effective in controlling the flow separation than other types of blowing jet configuration tested in this research. Moreover, when the pulsating blowing was applied, the stall angle was postponed about 2°-3°. The continuous and pulsating blowing jet is a direct and effective flow separation control for improving the aerodynamic characteristics and performances of airfoil.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.6 no.4
• /
• pp.29-37
• /
• 2003

Using a wind tunnel testing, the aerodynamic load characteristics of an elliptic airfoil was described. The experimental data was obtained for angles of attack $-20^{\circ}$ to $+20^{\circ}$ with $2^{\circ}$ increments at a chord Reynolds number of $0.99{\times}105$ and $2.48{\times}105$. For each test case, chordwise suction pressure distributions and wake surveys were obtained. Static pressure measurements were made over a 10 sec averaging time at a 10 Hz sampling rate. For each case, wake survey was conducted with a pilot-static probe at 1.0c downstream from the trailing edge at very fine spacing to resolve the wake velocity deficit profile. As can be expected, suction pressure coefficient was increased with angle of attack. The normal force, CNmax, appeared peak value at the incidence angle of $12^{\circ}~14^{\circ}$, and the significant increase in profile drag at this range of angles of attack.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.12
• /
• pp.1173-1183
• /
• 2009

In order to reduce the download around the Smart UAV(SUAV) at hovering, flow control using synthetic jet has been performed. Many of the complex tilt rotor flow features are captured including the leading and trailing edge separation, and the large region of separated flow beneath the wing. In order to control the leading edge and trailing edge separation, synthetic jet is located at 0.01c, $0.3c_{flap}$, $0.95c_{flap}$. As non-dimensional frequency, the flow pattern is altered and the rate of drag reduction is changed. The results show that synthetic jets shorten the vortex period and decrease the vortex size by changing local flow structure. By using leading edge jet and trailing edge jet, download is efficiently reduced compared to no control case at hovering mode.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.32 no.5
• /
• pp.10-17
• /
• 2004

To achieve the advanced forward flight performance of helicopter, the passive control methods for enhancement of the dynamic stall characteristics of rotor blades are studied. To enhance the dynamic stall characteristics of the rotor blades, it is essential to improve the lift performance and the pitching moment performance simultaneously with the control of the separation on the rotor blades. For this point of view, both the fixed droop leading edge and the Gurney flap which are simply realized are used for control of the dynamic stall in severe dynamic stall conditions. From this study, the combination of both passive control methods showed dramatic enhancement of lift and pitching moment performance in dynamic stall than previous research results.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.2
• /
• pp.57-80
• /
• 1994

항공기에 사용되는 2차 조종면은 플랩, 탭, 스포일러 등 여러 종류가 있으며 이중 spoiler는 공력제어 기능을 가지고 항공기의 조종성에 영향을 미치는 조종면으로 속도 감속이나 옆놀이 조종용으로 사용된다. 본 연구에서는 비행제어용 spoiler 기능과 고양항력을 얻을 수 있는 새로운 장치인 고양항력 panel에 대한 공력특성 및 비행제어 특성에 대하여 연구하였다. 이러한 고양항력 panel은 재래식인 spoiler가 양력을 감소시키고 항력만 증가시키는 장치인데 반하여 양력과 항력을 동시에 증가 시킬 수 있는 새로운 장치로서 날개의 앞전 윗면에 스팬방향으로 설치하여 슬롯효과를 발생시킴으로써 최대 양력 받음각에서 앞전에서의 박리를 막아 비행기의 착륙시 양력의 급작스러운 감소로 인한 불안정성을 감소시키게 된다. 본 논문에서는 직사각형 날개 및 FA-200모형의 날개위에 고양항력 panel을 설치하여 풍동실험 및 수치계산을 한 결과를 기술하였다. 실험결과 직사각형 날개의 경우 고양항력 panel의 위치는 날개의 앞전에 설치할 경우 고받음각에서 실속지연의 효과와 함께 후방실속의 특성을 향상 시킬 수 있으며, 항력의 증가로 인한 스포일러 효과를 얻을 수 있다. 양항비특성은 고양항력 panel을 날개의 앞전에설치하고, 그폭이 시위의 1/5이고, 붙임각 ${\theta}$가 $10^{\circ}$, 높이가 시위의 3/20일때 받음각 $18^{\circ}$ 이후에서 우수한 특성을 나타내었다. FA-200 모형의 경우 옆놀이 모멘트계수는 받음각이 작을 때 고양항력 panel의 슬롯간격과 붙임각이 작을수록 커지나 받음각이 커지면 붙임각이 커짐에 따라 증가함을 알 수 있다. 또한 키놀이 모멘트계수는 크게 변화하지 않으나 항력 특성은 고양항력 panel의 붙임각이 증가함에 따라 증가하였다. 고양항력 panel의 붙임각이 큰 범위에서 (${\theta}$ =$10^{\circ}$) 공기력의 증가는 고양항력 panel의 시위가 날개시위의 30%이고 슬롯의 폭이 날개시위의 10%일때 증가하는 결과를 얻을 수 있다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.521-529
• /
• 2017

Three-dimensional flow characteristics within a high-acceleration first-stage turbine vane passage has been investigated in a newly-built vane cascade for propulsion. The result shows that there is a strong favorable pressure gradient on the vane pressure surface. On its suction surface, however, there exists not only a much stronger favorable pressure gradient than that on the pressure surface upstream of the mid-chord but also a subsequent adverse pressure gradient downstream of it. By employing two different oil-film methods with upstream coating and full-coverage coating, a four-vortex model horseshoe vortex system can be identified ahead of each leading edge in the cascade, and the separation line of inlet boundary layer flow as well as the separation line of re-attached flow is provided as well. In addition, basic flow data such as secondary flow, aerodynamic loss, and flow turning angle downstream of the cascade are obtained.