• Membrane Journal
• /
• v.27 no.5
• /
• pp.425-433
• /
• 2017

As the problems related to the environmental pollution such as carbon dioxide emission are emerging, the need for the renewable energy and environmentally friendly energy is getting intense. Fuel cells are eco-friendly energy generation devices that generate electrical energy and produce water as a sole by-product. Compared to the traditional proton exchange membrane fuel cell (PEMFC), anion exchange membrane alkaline fuel cell (AEMAFC) has a main advantage of possibility to use low cost metal catalysts due to its faster kinetics. The AEM, which conducts $OH^-$ ions, should possess high ion conductivity as well as high chemical stability at high pH conditions. We hereby introduce a crosslinked poly(2,6-dimethyl-1,4-phenylene oxide) having a spacer-type conducting group as novel AEM, and report a high ion conductivity ($67.9mScm^{-1}$ at $80^{\circ}C$) and mechanical properties (Young's modulus : 0.53 GPa) as well as chemical stability (6.8% IEC loss at $80^{\circ}C$ for 1,000 h,) for the developed membrane.

• Korean Chemical Engineering Research
• /
• v.47 no.1
• /
• pp.38-45
• /
• 2009

In this study, interfacial properties were measured for imidazoline type cationic surfactant system which has been widely used as a fabric softener, a dispersant, an anti-static agent, a bleach activator, and an emulsifier. The CMC of imidazoline surfactant was near $6{\times}10^{-5}mol/L$ and the surface tension at CMC was about 32 mN/m. It was found that surface tension was not affected by surfactant concentration but decreased with an increase in pH. The interfacial tension between 1 wt% aqueous solution and n-dodecane was shown to be about 0.01 mN/m and equilibration time was not affected by pH. Phase behavior experiment in a binary aqueous surfactant system showed that only micellar solution of $L_1$ phase was found under conditions of temperature and pH investigated during this study. Only a two-phase region consisting of lower-phase microemulsion in equilibrium with excess oil phase existed under the same conditions, when oil was added to the binary surfactant system. The foam stability measured with 1 wt% surfactant solution increased with pH, which is consistent with surface tension measurement result. QCM(quartz crystal microbalance) measurement showed that surfactant adsorption increased with surfactant concentration but decreased with pH. According to the friction measurement, best fabric softening effect by imidazoline surfactant system was found under alkali conditions.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.9-15
• /
• 2005

In order to know the electrochemical decomposition characteristics of ammonia to nitrogen, this work has studied several experimental variables on the electrolytic ammonia decomposition. The effects of pH and chloride ion at $IrO_2$, $RuO_2$, and Pt anodes on the electrolytic decomposition of ammonia were compared, and the existence of membrane equipped in the cell and the changes of the current density, the initial ammonia concentration and so on were investigated on the decomposition. The performances of the electrode were totally in order of $RuO_2{\approx}IrO_2>Pt$ in the both of acid and alkali conditions, and the ammonia decomposition was the highest at a current density of $80mA/cm^2$, over which it decreased, because the adsorption of ammonia on the electrode surface was hindered due to the evolution of oxygen. The ammonia decomposition increased with the concentration of chloride ion in the solution. However, the increase became much dull over 10 g/l of chloride ion. The $RuO_2$ electrode among the tested electrodes generated the most OH radicals which could oxidized the ammonium ion at pH 7.

• Resources Recycling
• /
• v.19 no.1
• /
• pp.40-48
• /
• 2010

It was investigated that effects of NaOH concentration on synthesis of mesoporous materials using municipal solid waste incinerator ash slag (MSWI-ash slag). In order to increase the purity and maximize the amount of extracted Si content the raw MSWI-ash slag was mechanically activated. Extraction of Si from the MSWI-ash slag was carried out by alkali treatment using concentrated NaOH solution, which varied from 1M to 4M. Physical properties (i.e., pore size, specific surface area and total pore volume) of the synthesized mesoporous silica were also evaluated as a function of NaOH concentration via BET, SEM, TEM and small-angle X-ray scattering analyses. Over the entire range of NaOH concentration investigated (i.e., 1-4M), the synthesized mesoporous materials were determined to be SBA-15, which exhibited a hexagonal structure with the pore size of approximately 7 nm. On the other hand, specific surface area and total pore volume increased with NaOH concentration up to 3M while the values decreased at 4M, indicating that the optimal NaOH concentration for the synthesized mesoporous silica was approximately 3M. Further comparison analysis between two conditions (3M versus 4M) showed that the decrease in two physical properties at 4M NaOH concentration was likely due to the potential inhibition by excess Na ions on the formation of mesophase and the consequent increase of pore wall thickness by remaining Si ions.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.31 no.1
• /
• pp.82-89
• /
• 1998

Partial hydrolyzing condition for low-molecularized alginate and rheological properties such as viscosity, solubility, emulsitying ability, oil absorption capacity, bile acids binding and metal ion binding of the low-molecularized alginates from the sea mustard ( Undaria pinnatifida) and giant kelp (Macrocystis pyrifera) were investigated. Alginate from sea mustard was regularly hydrolyzed with the increase of HCl concentration in the range of 0.2 N to 0.5 N and with the prolonged reaction time at $100^{\circ}C$. The molecular weight of alginate was decreased to a part of 100 after hydrolysis for 50 min with 0.3 N HCl. The ratio of mannuronate to guluronate was increased with the acid hydrolysis and total yield was estimated to be $75\%\~80\%$. Low-molecularization of alginate was featured in the apparent decrease of viscosity, whereas solubility, emulsifying ability, and bile acids binding ability were increased with the low-molecularization. Oil absorption capacity of the acid$\cdot$alkali soluble alginate was slightly higher than that of the water soluble alginate. Metal ion binding capacity was the highest in acid$\cdot$alkali soluble alginate, and decreased with the low-molecularization.

• Membrane Journal
• /
• v.29 no.3
• /
• pp.173-182
• /
• 2019

Much research has been made for finding new and eco-friendly alternative sources of energy to solve the problems related with the pollution caused by emissions of greenhouse gases such as carbon dioxide as the use of fossil fuels increases worldwide. Among them, fuel cells draws particular interests as an eco-friendly energy generator because only water is obtained as a by-product. Anion exchange membrane-based alkaline fuel cell (AEMFC) that uses anion exchange membrane as an electrolyte is of increased interest recently because of its advantages in using low-cost metal catalyst unlike the PEMFC (potton exchange membrane fuel cell) due to the high-catalyst activity in alkaline conditions. The main properties required as an anion exchange membrane are high hydroxide conductivity and chemical stability at high pH. Recently we reported a chemically crosslinked poly(2-dimethyl-1,4-phenylene oxide) (PPO) by reacting PPO with N,N,N',N'-tetramethyl-1,6-hexanediamine as novel anion exchange membranes. In the current work, we further developed the same crosslinked polymer but having enhanced physicochemical properties, including higher conductivity, increased mechanical and dimensional stabilities by using the PPO with a higher molecular weight and also by increasing the crosslinking density. The obtained polymer membrane also showed a good cell performance.

• Applied Chemistry for Engineering
• /
• v.10 no.7
• /
• pp.996-1002
• /
• 1999

The oxalate precipitation of lanthanide and actinide by oxalic acid was investigated in the simulated radioactive liquid waste, which was composed of 17 elements of alkali, alkaline earth(Cs, Rb, Ba, Sr), transition metal(Zr, Fe, Mo, Ni, Pd, Rh), lanthanide(La, Y, Nd, Ce, Eu) and actinide(Np, Am) in nitric acid solution. The effect of concentrations of nitric acid and ascorbic acid on the precipitation yield of each element in the simulated solution was examined at 0.5 M oxalic acid concentration. The precipitation yields of the elements were usually decreased with nitric acid concentration, nevertheless, the precipitation yields of lanthanide and actinide were more than 99%. Palladium was precipitated due to the reduction of Pd(II) into Pd metal by the addition of ascorbic acid in the oxalate precipitation and then, the precipitation yields of Mo, Fe, Ni, Ba decreased by 10~20% with concentration of ascorbic acid. The reductive precipitation of Pd(II) into Pd metal by the addition of ascorbic acid into the simulated radwaste occurred at below 1 M nitric acid concentration and its yield showed maximum at the ascorbic acid concentration of 0.01~0.02 M. The hydrazine suppressed the reductive precipitation of Pd by the ascorbic acid.

• Journal of the Korea Concrete Institute
• /
• v.18 no.2 s.92
• /
• pp.267-274
• /
• 2006

Greenhouse gas reduction will be highlighted as the most pending question in the cement industry in future because the production of Portland cement not only consumes limestone, clay, coal, and electricity, but also release waste gases such as $CO_2,\;SO_3$, and NOX, which can contribute to the greenhouse effect and acid rain. To meet the increase of cement demand and simultaneously comply with the Kyoto Protocol, cement that gives less $CO_2$ discharge should be urgently developed. This study aims to manufacture non-sintering cement(NSC) by adding phosphogypsum(PG) and waste lime(WL) to granulated blast furnace slag(GBFS) as sulfate and alkali activators. This study also Investigates the hydration reaction of NSC through analysis of scanning electron microscopy(SEM), X-ray diffraction(XRD), differential thermal analysis(DTA), and pH. Results obtained from analysis of the hydrate have shown that the glassy films of GBFS are destroyed by the activation of alkali and sulfate, ions eluted from the inside of GBFS react with PG and produce ettringite, and consequently the remaining component in GBFS slowly produced C-5-H(I) gel. Here, PG is considered not only to play the role of simple activator, but also to work as a binder reacting with GBFS.

• Journal of Life Science
• /
• v.25 no.9
• /
• pp.1021-1026
• /
• 2015

Invertase (β-D-fructosfuranosidase, EC 3.2.1.26) catalyzes the hydrolysis of sucrose into D-glucose and D-fructose. Three biochemical subgroups of invertases have been investigated in plants: vacuolar (soluble acid), cytoplasmic (soluble alkaline), and cell wall-bound (insoluble acid) invertases. An isoform of neutral invertase was purified from pea seedlings (Pisum sativum L.) and treated with gibberellic acid (GA) by sequential procedures consisting of ammonium sulfate precipitation, ion-exchange chromatography, absorption chromatography, and reactive green-19 affinity chromatography. The results of the overall insoluble invertase purification were a 430-fold increase. The purified neutral invertase was not glycosylated and had an optimum pH between neutral and alkaline (pH 6.8-7.5). It was inhibited by Tris, as well as by heavy metals, such as Hg²⁺ and Cu²⁺. Typical Michaelis–Menten kinetics were observed when the activity of the purified invertase was measured, with sucrose concentrations up to 100 mM. The K_m and V_max values were 12.95 mM and 2.98 U/min, respectively. The molecular mass was around 20 kDa. The sucrose-cleaving enzyme activity of this enzyme is similar to that of sucrose synthase and fructosyltransferase, but its biochemical characteristics are different from those of sucrose synthase and fructosyltransferase. Based on this biochemical characterization and existing knowledge, neutral INV is an invertase isoform in plants.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.32 no.6
• /
• pp.774-778
• /
• 1999

Tee yields, physical properties and gel formation abilities or hot-water extractable material (HWEM) and water-soluble alginate (WSA) extracted from Laminaria japonica were estimated and compared with those of the alginate (ASA) extracted with alkali solution in the routine procedure. The contents of HWEM, WSA and ASA in Laminaria japonica were 8.3, 2.5 and $19.1\%$, respectively. The HWEM and WSA had no gel formation ability, whereas the ASA had a good gol formation ability. The HWEM and WSA were almost not viscous even in $1.5\%$ of the sample solution, whereas the ASA was very highly viscous in above $0.5\%$ of sample solution. The melting points of $1\%$ solution of HWEM, WSA and ASA sample were 31, 24 and $14^{\circ}C$, respectively. The solubility at melting point of each samples varied from 2.3 to 2.6 g/100 g water, and a few differences were observed.