• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.38 no.1
• /
• pp.63-71
• /
• 2018

In this study, the torque and horizontal stress acting on vane were measured and then used to determine a friction angle of sand. A dry Nakdong River sand was prepared for loose and dense conditions in a cell and then pressurized with 25, 50, 75 or 100 kPa from the surface of sand. A vane (5cm in diameter and 10cm in height) was rotated and the torque and horizontal stress were measured at real time. A maximum torque was 3.5-9.5Nm for loose sand and 7.4-17.6Nm for dense sand, respectively. The maximum torque increased as an overburden pressure increased. The maximum torque obtained at 14-20 degrees of vane rotation, which was not influenced by the initial alignment of earth pressure and vane blade. An initial horizontal stress ratio was 0.33-0.35 on the average. The horizontal stress increased initially and then decreased due to particle disturbance. A friction angle was calculated from real time varying horizontal stress and torque, which decreased with increasing overburden pressure. The friction angle of loose sand from vane shear test was similar to that of direct shear test but that of dense sand was overestimated.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.32 no.3
• /
• pp.472-480
• /
• 2005

The purpose of this study was to investigate the effective penetration methods of acid etching agents in the pit and fissures on the occlusal surface. Extracted maxillary first and second premolars were divided into 4 groups : to Group I only acid etching agent was applied, to Group II ultrasonic scaler as well as acid etching agent were applied, to Group III after fissurotomy acid etching agent was applied, and to Group IV after fissurotomy the same process performed with Group II. The comparison between the 4 groups by the use of scanning electron microscope showed the results as follows : 1. Comparing each groups with regard to the penetration rate(%) of acid etching agents, Group III and Group IV showed improved penetration rate(%) compared with Group I. Group II made no significant different results from Group I, but had somewhat better penetration rate(%). 2. Comparing each groups with regard to the penetration rate(%) of acid etching agents according to regions within fissures, Group III and Group IV showed more improved penetration rate than Group I in the mesial pit and distal pit. However, no significant difference between each groups was showed in the middle fissure.

• Restorative Dentistry and Endodontics
• /
• v.32 no.6
• /
• pp.491-497
• /
• 2007

The purpose of this study was to compare apical sealing ability of continuous wave canal filling technique according to various heat source plugging depths. Eighty one extracted human premolars with straight root were cleaned and shaped to size 35 using .06 taper rotary NiTi file. After cleansing and shaping, the teeth were divided into 5 groups following the heat source probing depths from the apex; 3, 4, 5, 6 and 7 mm. All specimens were filled using E&Q plus with #35/.06 tapered gutta-percha cone. The positive control teeth were not filled. All teeth were coated with nail varnish except the apical 1 mm around the apical foramen. Negative control teeth were completely sealed include the apical foramen. All specimens were immersed in 1% methylene blue solution for 72 hours. Then the specimens were sectioned horizontally at 1, 2 and 3 mm from the root apex. Each sectioned surface was photographed using a digital camera attached to the stereomicroscope at $12.5{\times}2.5$ fold magnification. All points at 1, 2 and 3 mm were summed as final score of one specimen. Statistical analysis of the collected data was performed. Under the condition of this study. there was no significant difference between the heat source plugging depths of 3, 4, 5, 6 and 7 mm in apical sealing ability. All of apical heat source plugging depth from 3 to 7 mm including Buchanan's protocol -from 5 to 7 mm- seems to be acceptable in clinical application.

• Restorative Dentistry and Endodontics
• /
• v.33 no.4
• /
• pp.377-388
• /
• 2008

The aim of the present study is to compare the corrosion tendency using two kinds of NiTi files in the various environmental conditions through the visual examination and electrochemical analysis. ProTaper Universal S2, 21 mm (Dentsply Maillefer, Ballaigues, Switzerland) and Hero 642, 0.06 tapers, size 25, 21 mm (Micromega, Besancon, France) rotary instruments were tested. The instruments were randomly divided into eighteen groups (n = 5) by the immersion temperature, the type of solution, the brand of NiTi rotary instrument and the presence of mechanical loading. Each file was examined at various magnifications using Scanning Electron Microscope (JEOL, Akishima, Tokyo, Japan) equipped with energy dispersive X-ray microanalysis (EDX). EDX was used to determine the components of the endodontic file alloy in corroded and noncorroded areas. The corrosion resistance of unused and used NiTi files after repeated uses in the human teeth was evaluated electrochemically by potentiodynamic polarization test using a potentiostat (Applied Corrosion Monitoring, Cark-in-Cartmel, UK). Solution temperature and chloride ion concentration may affect on passivity of NiTi files. Under the conditions of this in vitro study, the corrosion resistance is slightly increased after clinical use.

• Journal of IKEEE
• /
• v.16 no.3
• /
• pp.217-223
• /
• 2012

This paper presents design and operational characteristics of 150 MW pulse power system for high current pulse forming network to control trigger time. The system is composed of two capacitor bank modules. Each capacitor bank module consist of a trigger vacuum switch, 9k 33kJ capacitor, an energy dump circuit, a crowbar circuit and a pulse shaping inductor and is connected in parallel. It is controlled by trigger controller to select operational module and determine triggering time. Pspice simulation was conducted about determining parameters of components such as crowbar circuit, capacitor, pulse forming inductor, trigger vacuum switch and predicting results of experiment circuit. The result of the experiment was in good agreement with the result of the simulation. The various current shapes with 300~650 us pulse width is formed by sequential firing time control of capacitor bank module. The maximum current is about 40 kA during simultaneous triggering of two capacitor bank modules. The developed 150 MW pulse power system can be applied to high current pulse power system such as rock fragmentation power sources, Rail gun, Coil gun, nano-powers, high power microwave.

• Restorative Dentistry and Endodontics
• /
• v.29 no.5
• /
• pp.446-453
• /
• 2004

The aim of this study was to evaluate the shaping abilities of four different rotary nickel-titanium instruments with anticurvature motion to prepare root canal at danger zone by measuring the change of dentin thickness in order to have techniques of safe preparation of canals with nickel-titanium files. Mesiobuccal and mesiolingual canals of forty mesial roots of extracted human lower molars were instrumented using the crown-down technique with ProFile, $GT^{TM}$ Rotary file, Quantec file and $ProTaper^{TM}$. In each root, one canal was prepared with a straight up-and-down motion and the other canal was with an anticurvature motion. Canals were instrumented until apical foramens were up to size of 30 by one operator. The muffle system was used to evaluate the root canal preparation. After superimposing the pre- and post-instrumentation canal. change in root dentin thickness was measured at the inner and outer sides of the canal at 1. 3, and 5 mm levels from the furcation. Data were analyzed using two-way ANOVA. Root dentin thickness at danger zone was significantly thinner than that at safe zone at all levels (p < 0.05). There was no significant difference in the change of root dentin thickness between the straight up-and-down and the anticurvature motions at both danger and safe zones in all groups (p > 0.05). ProTaper removed significantly more dentin than other files especially at furcal 3 mm level of danger and safe zones (p < 0.05) Therefore, it was concluded that anticurvature motion with nickel-titanium rotary instruments does not seem to be effective in danger zone of lower molars.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.43 no.3 s.309
• /
• pp.78-84
• /
• 2006

Our study aimed at quantitative assessment of a cleft palate nose deformity condition by analyzing the following parameters gathered from a photographic image of a cleft palate patient: (1) angle difference between two nostril axes, (2) center of the nostril and distance between two centers, (3) overlapped area of two nostrils, and (4) the overlapped area ratio of the two nostrils. A regression equation of doctor's grades was obtained using the eight parameters. Three plastic surgeons gave us the glades for the each photographic image by to increments with maximum grade of 100. The average reproducibility of the grades given by the three plastic surgeons and the three laymen using the developed program was $10.8{\pm}4.6%\;and\;7.4{\pm}1.8%$, respectively. Kappa values representing the degree of consensus of the plastic surgeons and the three laymen were 0.43 and 0.83, respectively. Correlation coefficient of the grades evaluated by the surgeons and obtained by the regression equation was 0.642 and that of the grades by the surgeons and by the neural network was 0.798. In conclusion, the developed neural network model provided us better reproducibility, much better consensus, and better correlation than doctor's subjective evaluation in addition to objectiveness and easy application.

• Polymer(Korea)
• /
• v.25 no.6
• /
• pp.855-865
• /
• 2001

The optimization condition of injection molding for a commercial product of TV speaker grille of A Company was induced using a CAE software of Moldflow. The flow and packing phase analysis was performed by using flow balance, runner balance, and the intermediate one by using the above two balances, which were used for controlling the amount of packing resins into the cavity, Later, the analysis performed by using the measured viscosity (local database) at various shear rates and the results were compared with the computer simulation using the standard database. Flow balance induced minimized weld line resulted in a better appearance and physical properties of the were line, but exhibited a disadvantage of large deformation and gas formation due to over-packing of the molten resin in the center of the speaker grille. Runner balance improved the disadvantage of the flow balance by controlling the amount of molten resin injected from the gate, however resulted reduced mechanical properties and poor appearance of the weld line. However, the modified method induced from the flow and runner balance improved the disadvantages by changing the runner size. In addition, the analyses based on the local database and the standard database were compared. Although the measured viscosity was slightly higher and the temperature distribution was broader than the standard database, no distinct difference was obtained from the analysis using the two different databases.

• Journal of Chest Surgery
• /
• v.29 no.3
• /
• pp.331-336
• /
• 1996

Four operative cases of aortic valvuloplasty with leaflet extension technique using glutaraldehyde preserved tautologous pericardium are described. All patients had severe aortic regurgitation on preoperative echocardiogram, and Grade W AR on oath-angiogram. The causes of aortic regurgitation were rheumatic fever in 2 cases, degenerative change in 1 case, and 1 case of unknown cause. The autologous pericardium was fixed In a 0.625% glutaraldehyde solution for 15 minutes and rinsed in saline for an additional 15 minutes. Leaflet extension technique varied in 4 patients depending on the site and the extent of the leaflet size and lesion. There was no hospital mortality and no thromboembolic episode without anticoagulation. Post-operative cardiac size was reduced on simple chest film in all cases, and LVESD and LVEDD were reduced on folio w- up echo cardi o gram . This experience permits us to conclude that leaflet extension technique is simple and safe in valve r construction, allowing repair of aortic valves that need to be replaced.

• Journal of Korean Society of Forest Science
• /
• v.104 no.2
• /
• pp.179-186
• /
• 2015

This study was conducted to understand the characteristics of flowering and the factors affecting fruiting grades of Acer pictum subsp. mono(APSM), We examined the characteristics of flowering and fruiting in various natural APSM forest, and investigated annual fruiting grade, DBH, tree height, number of APSM trees within 30 m on 29 selected trees in the natural broadleaved forest in Mt. Jungwang in Gangwon-do, from 2009 to 2014. APSM has heterodichogamous sexual system consist of protoandry and protogyny. Eight trees have changed their sex morphs; 3 trees change the sex morph PA to PG, and 5 trees does the sex morph PG to PA. Early fall of young ovary is concentrated until early July. Initially, the small samaras are common, and was gradually increased the samaras suffered insect damage. Most flowers of APSM are pollinated by Andrenidae sp., Syrphidae sp. and Tachinidae sp.. Number of early fall samaras and the status of fallen samaras showed a significant difference by the year and region. Corymbose panicle and young leaves developed on the top of APSM twigs. Newly grown opposite twigs of APSM did not grow sufficiently and had no floral buds. The highest fruiting grade of tree was 9.0, and the mean values was only 3.8. The highest fruiting grade of year was 4.55 in 2013, and the lowest did 0.07 in 2014. Highly significantly correlated and regressed between mean of annual fruiting rates and rates of crown under sun light. This results would imply that thinning for tree growth through improved light absorption might be a method to enhance seed production of APSM in the seed production forest.