• Journal of IKEEE
• /
• v.8 no.1 s.14
• /
• pp.152-159
• /
• 2004

In this study, we design the one-chip PWM IC with high voltage power switch (300V class LDMOSFET) for SMPS (Switching Mode Power Supply) application. Reference circuits generate constant voltage(5V) in the various of power supply and temperature condition. Error amp. is designed with large DC gain $({\simeq}65dB)$, unity frequency $({\simeq}190kHz)$ and large $PM(75^{\circ})$. comparator is designed with 2 stage. Saw tooth generators operate with 20kHz oscillation frequency. Also, we optimize drift concentration & drift length of n-LDMOSFET for design of high voltage switching device. It is shown that simulation results have the breakdown voltage of 350V. (using ISE-TCAD Simulation tool). PWM IC with power switching device is designed with 2um design rule and Bi-DMOS technology.

• Journal of IKEEE
• /
• v.18 no.4
• /
• pp.586-592
• /
• 2014

In this paper, high efficiency power management IC(PMIC) with DT-CMOS(Dynamic threshold voltage Complementary MOSFET) switching device is presented. PMIC is controlled PWM control method in order to have high power efficiency at high current level. The DT-CMOS switch with low on-resistance is designed to decrease conduction loss. The control parts in Buck converter, that is, PWM control circuit consist of a saw-tooth generator, a band-gap reference(BGR) circuit, an error amplifier, comparator circuit, compensation circuit, and control block. The saw-tooth generator is made to have 1.2MHz oscillation frequency and full range of output swing from supply voltage(3.3V) to ground. The comparator is designed with two stage OP amplifier. And the error amplifier has 70dB DC gain and $64^{\circ}$ phase margin. DC-DC converter, based on current mode PWM control circuits and low on-resistance switching device, achieved the high efficiency nearly 96% at 100mA output current. And Buck converter is designed along LDO in standby mode which fewer than 1mA for high efficiency. Also, this paper proposes two protection circuit in order to ensure the reliability.

• Journal of the Korean Institute of Gas
• /
• v.17 no.2
• /
• pp.85-89
• /
• 2013

The purpose of the development of KC-1 LNG cargo containment system is reduction in royalty and increase in competitiveness of shipbuilding industry. An assessment of structure safety for LNG cargo containment system under sloshing load due to ship motion has become an important design element. The ideal way is to implement fully interaction of the fluid domain and the cargo containment system. However the irregular sloshing pressure were idealized in the form of a triangular wave for safety assessment because the fluid- structure interaction analysis is taken the extensive computation time and difficult to ensure the accuracy of the results. In this study, the sloshing load was assumed to be a triangular wave with a maximum pressure of 10 bar during 15/1000 seconds. In the analytic results, the basic insulation panel of KC-1 LNG cargo containment system was assessed to be structurally safe for sloshing load.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2004.03a
• /
• pp.535-541
• /
• 2004

GPS는 직접적인 시통 및 거리에 대해 제한을 받는 일반 재래식 측량으로는 관측하기 힘든 중ㆍ장기선 관측의 경우 기선결정에 대한 정확도와 활용성이 우수하다고 알려져 있다. 그러나 현재 실질적으로 관측하여 취득하고자 하는 위치정보를 얻기 위해 지역의 대소에 관계없이 고가의 이주파 수신 장비를 사용하고 있으며, 최적의 기선해석과 망조정에 의한 성과를 얻기 위한 데이터 처리과정이 엄밀하게 확립되어 있지 않다 이러한 이유들로 인하여 고가의 이주파 수신기가 여러 분야에 적용되고 있으며, 성과물를 산출하고 있는 실정이다. 본 연구에서는 이주파 수신기를 사용하여 전국에 산재하고 있는 국가 기준삼각점을 대상으로 관측을 실시하여, 일주파만을 처리하는 L₁ Only 방식과 이주파를 처리하는 L₁&L₂ 방식과의 비교 분석하여 일주파에 대한 정확도와 적용성 그리고 기선의 거리에 따른 한계성에 대해 검증하고자 한다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.17 no.3
• /
• pp.283-292
• /
• 1999

Aerotriangulation for the large scale mapping(photo-scale l/5,000) was studied with the projection center determined by kinematic DGPS positioning. For the feasibility study, the accuracy and error was analyzed with the comparison between a projection center from the conventional model adjustment and the projection center determined by the kinematic DGPS positioning. Kinematic DGPS-supported Bundle adjustment was also performed. The accuracy of projection center, determined by L1 phase data observed within 30 km from base station, was stable, and the planimetric accuracy(RMS) is 13 cm and the vertical accuracy(RMS) is 15 cm with 4 ground control points, which satisfies the national standard of digital mapping. Thus, this study shows that GPS-assisted aerotriangulation can be used for economic digital mapping.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.10a
• /
• pp.103-107
• /
• 2003

현재 관측점간의 3차원 상대위치를 구하고 기준점의 측지학적 좌표ㆍ표고를 결정하는 작업을 수행하는 GPS(Global Positioning System) 측량은 신호가 전파인 관계로 대기권의 전파지연 오차를 포함하게 되며, 전리층 지연은 주파수에 반비례하는 특성이 있으므로 지역의 대소에 구분 없이 이주파수 수신기(dual-frequency GPS receiver)를 사용하여 정확하게 지연시간을 측정하고 그로 인한 측위정밀도의 정확성을 확보하고 있다. 본 연구는 비교적 낮은 가격인 일주파 수신기를 사용하여 기선거리별로 삼각점을 선점한 후 동일 시간에 관측을 실시하고 취득한 데이터 값을 추출한 후 기선거리에 따른 허용오차를 분석하고, 그 활용성 및 경제성과 일주파 수신기의 기선에 대한 사용 가능성을 분석하였다. 그 결과, 100km이내의 지역에서는 일주파 수신기 만으로도 충분히 만족스러운 결과를 얻을 수 있었다.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1218-1219
• /
• 2011

본 논문은 KA555 Timer을 이용한 PWM회로로 구성된 아날로그 방식의 DC-DC Buck Converter와 AVR ATmega128를 이용한 PWM회로로 구성된 디지털 방식의 Buck Converter을 설계하여 각각의 특성을 비교 분석하였다. 제안된 컨버터들은 공통적으로 전원을 공급받아 전압분압회로를 통해 DC-DC Buck Converter의 PWM 제어회로부에 공급되며, 아날로그방식 컨버터의 제어부는 KA555 timer을 이용하여 구형파회로와 미분회로를 구성하고, 출력된 삼각파와 정현파를 KA555 timer을 이용하여 PWM파형으로 제어한다. 디지털방식의 컨버터는 AVR RISC 8-bit 마이크로프로세서 ATmega128을 이용하여 PWM 제어부를 구성하고 이를 LCD창을 통해 그 값을 확인할 수 있도록 설계하였다. 본 논문에서는 두 가지 방식의 제어부를 구성하여 제작 및 실험함으로써, 각각의 장단점을 비교하여 시스템 구성시 요구조건인 소형경량, 단가저감, 효율 등을 비교하여 그 상황에 맞는 설계가 가능할 것이다.

• The Journal of the Acoustical Society of Korea
• /
• v.14 no.2
• /
• pp.30-39
• /
• 1995

In this paper, study on implementation of FFT analyzer applied to CAT, A/D conversion module, DSP module and VXIbus interface module are implemented in hardware and calculation program and control software are implemented in DSP module and VXIbus interface module, respectively. The control of the modules using PC is realized in software. The real time bandwidth of the FFT analyzing device is 100KHz. At sampling rate of 200KHz and with 2048 point FFT, the result of applying sine, triangular and rectangular wave of 20KHz to FFT analyzing device is compared with the FFT analyzed results of Hewlett-Packard 3562A dynamic output range of -40dBV- +30dBV, correct results are obtained and results of applying 10KHz, 20KHz and 50KHz input are compared and the correct values are obtained.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.16 no.2
• /
• pp.195-202
• /
• 1998

In this study, we utilized various type of GPS observation measurements to get a camera projection center of the aerial triangulation and consequently to determine which type is acceptable. For the accuracy and the error analysis, comparison between a projection center from the conventional model adjustment and the result determined by the kinematic DGPS positioning which is fitted to the conventional model adjustment using 3D conformal transformation method has been made. The camera projection center is located within a $\pm{2m}$ for C/A code range measurements, $\pm{14cm}$ for L1 phase measurements and $\pm{10cm}$ for L1/L2 phase measurements with $1\sigma$. In this way, the accuracy of the camera projection center by the bundle block adjustment can be predicted.

• Korean Journal of Optics and Photonics
• /
• v.17 no.2
• /
• pp.127-135
• /
• 2006

We implement numerical simulations for the distributed optical fiber sensor system that uses the spatially-selective Brillouin scattering, by treating the superposition of the optical-frequency-modulated pump/probe waves in the time domain. We obtain temporal and spatial distributions of Brillouin gain for various cases. Simulations are applied to the case of concatenated optical fibers of different kinds and the case of distributed temperature along the fiber, which give reasonable results for the distributed sensor. The result of using a triangular wave instead of a sinusoidal one as a modulation waveform shows that the triangular wave modulation has an advantage in spatial resolution.