• Journal of Cadastre & Land InformatiX
• /
• v.45 no.2
• /
• pp.45-56
• /
• 2015

The main purpose of this investigation is to make up for the limitations of parcel addressing and to seek the application plan of cadastral triangulation point to effective installation of national index numbers. The test-bed has been constructed at the mountainous area located in Nowon-gu, seven cadastral triangulation points within the test-bed was directly applied to this investigation. Each points have been firstly converted from a plane rectangular coordinates to a single plane rectangular coordinates (UTM-K). To verify positioning results achieved from these points, a single plane rectangular coordinates through the Network-RTK was considered. With regards to verification result, maximum coordinate shift was revealed by 6 cm, this level of difference can be satisfied to Article 7, paragraph 2 "the regulation for National Index Number". This means that coordinate transformation applied with cadastral triangulation points can achieve the sastisfied result without local surveying. And also, remarkable effects have been created in terms of financial effectiveness and safe preservation of cadastral triangulation points due to the omission of local surveying.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.20 no.1
• /
• pp.39-46
• /
• 2002

This paper shows what is point to be considered at that time in cadastral settlement surveying after declination analysis between GPS and traditional surveying at coordinate result of cadastral triangulation points and supplementary point in site selected deplaning of streets which is surveyed traditional surveying. In the case that coordinates of cadastral triangulation assistance points was decided by standard of the existing cadastral triangulation points that direction of the error vector is in opposition, authors could know all errors was reduced inside coordinate by error being offset each other through the results of study. The coordinates result of cadastral triangulation point by standard of the cadastral triangulation points reduces the deviation value through error that an intersection points was centered being offset each other but through the result that a tendency of errors occurrence is analyzed goniometrys, supplementary points that is close to cadastral triangulation assistance points was affected by error of cadastral triangulation assistance points.

• Proceedings of the Korean Association of Geographic Inforamtion Studies Conference
• /
• 2008.10a
• /
• pp.13-15
• /
• 2008

LiDAR(Light Detection and Ranging)는 3차원공간정보를 신속하게 구축할 수 있는 최신 측량 기술로써 최근 그 활용도와 중요성이 높아지고 있다. 그러나 LiDAR 관측성과는 시스템 특성상 높은 수직 정확도를 제공하고 있으나 항공사진과 같이 정확한 평면위치를 측정하여 조정할 수 없으므로 상대적으로 낮은 수평 정확도를 가지고 있다. 본 연구에서는 LiDAR 관측에 의한 건물의 벽면 반사파를 이용하여 건물모서리의 평면 좌표(x, y)를 추출하고, 이를 항공삼각측량에 의한 평면좌표와 비교분석하였다. 그 결과 LiDAR의 평면좌표가 항공삼각측량에 의한 평면좌표에 비해 상대적으로 이동되어 있음을 확인할 수 있었다. 따라서, 2차원 좌표변환을 수행하여 LiDAR의 평면좌표를 보정하여 정확도를 향상시킬 수 있었고, 이를 이용하여 향후 LiDAR 관측성과 품질 향상에 도움이 될 것이라 기대한다.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.23 no.3
• /
• pp.273-282
• /
• 2005

A rapidly developed satellite technology is used in comprehensive fields such as spatial data aquisition and applications. Especially a GPS positioning is expected to reinvigorate at the national reference system changes to ITRF (International Terrain Reference Frame). Currently the National Geographic Information Institute (NGII) issues a triangulation point coordinate by separating old and new coordinates and in the year of 2007 it will be scheduled to be changed ITRF. The triangulation point coordinate in Cheju area causes some problems due to the difference original observation and re-observation. Thus in this study a GPS observation is conducted after re-organizing geodetic network based on 1st and 2nd order triangulation in order to check the current triangulation points in Cheju area. After the GPS observation data analysis, stable points were extracted, proposed a geodetic network and its application.

• Journal of Korean Society for Geospatial Information Science
• /
• v.14 no.1 s.35
• /
• pp.65-74
• /
• 2006

A rapidly developed satellite technology is used in comprehensive fields such as spatial data aquisition and applications. Especially a GPS positioning is expected to reinvigorate at the national reference system changes to ITRF(International Terrain Reference Frame). Currently the National Geographic Information Institute(NGII) issues a triangulation point coordinate by separating old and new coordinates and in the year of 2007 it will be scheduled to be changed ITRF. The triangulation point coordinate in Cheju area causes some problems due to the difference original observation and re-observation. Thus in this study a GPS observation is conducted after re-organizing geodetic network based on 1st and 2nd order triangulation in order to check the current triangulation points in Cheju area. After the GPS observation data analysis, stable points were extracted, proposed a geodetic network and its application.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.2 no.2
• /
• pp.1-13
• /
• 1984

Projection has been used in order to indicate the horizontal position of triangulation stations which had been existed on the earth surface. In our country, the plane Rectangular coordinate of the triangulation station is computed by means of Gauss Double projection. But it proves to contain many errors according to the difference in Latitude and longitude. Therefore, in this study Transverse Mercator projection which is known to contain less error than Gauss Double projection in an applied region is introduced, and the results obtain by two these projections and the value today in our country are compared and analysed. when an another plane Rectangular Coordinate system is added to the present 3-plane Rectangular Coordinate system, there is an object inshowing the best position.

• Journal of Advanced Navigation Technology
• /
• v.3 no.2
• /
• pp.139-146
• /
• 1999

A flight simulator is composed of engine, navigation systems and instrument modules. However, two problems exist here. First, the coordinate of each independent module is not same. To solve this problem, we design a method that mutual coordinates are capable of transformation each other. Second, the distance and bearing between two points on the earth are computed in a sphere shape using the spherical trigonometry. However, the computing time is very severe. In this paper, we project the sphere into the planar to reduce the computing time. An experimental result shows that the performance of the proposed method is excellent to both distance and bearing calculations in close region. Also, the computing time is reduced from $4.95{\times}10^{-4}$ seconds to $1.648{\times}10^{-4}$ seconds.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.16 no.2
• /
• pp.195-202
• /
• 1998

In this study, we utilized various type of GPS observation measurements to get a camera projection center of the aerial triangulation and consequently to determine which type is acceptable. For the accuracy and the error analysis, comparison between a projection center from the conventional model adjustment and the result determined by the kinematic DGPS positioning which is fitted to the conventional model adjustment using 3D conformal transformation method has been made. The camera projection center is located within a $\pm{2m}$ for C/A code range measurements, $\pm{14cm}$ for L1 phase measurements and $\pm{10cm}$ for L1/L2 phase measurements with $1\sigma$. In this way, the accuracy of the camera projection center by the bundle block adjustment can be predicted.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.15 no.2
• /
• pp.253-261
• /
• 1997

In general, the transformation of coordinates in GPS is carried out by 3 dimensional transformation method with 3-10 parameter. In korea, the coordinates of transformation points ware determined are adjusted in-dependently by planimetry and the height, and also the weight of observations were not properly applied to the adjustment. In this study, two different transformation methods are tested and analysed by the field test, and it is finally found that 2 dimensional method is more efficient way than 3 dimensional classical transformation method.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2003.04a
• /
• pp.65-68
• /
• 2003

국가기준점인 삼각점은 통일원점, 구소삼각원점, 특별소삼각원점으로 구분 설치하였으며, 이들은 설치기관, 시기, 방법, 측량단위와 원점 등이 모두 달라 측량성과가 같지 않으며 제각각 다른 자료체계로 등록되어 있다. 또한 삼각점들의 유지ㆍ관리 소홀로 실용성과에 한계를 드러내고 있으며, 최근 정밀1차기준점측량 성과를 고시하였으나 토지조사사업 당시의 성과와 많은 차이가 있어 지적측량의 활용에 많은 문제를 가지고 있다. 이러한 문제점을 파악하고 개선하고자 경기도 연천군 관내 삼각점과 지적삼각점에 대하여 GPS 관측을 실시하고 현행좌표로 변환하여 등록 자료와 비교 분석하고 이에 대한 문제점과 개선방안을 제시하였다.