• Journal of IKEEE
• /
• v.18 no.1
• /
• pp.128-133
• /
• 2014

This paper suggest hysteretic buck converter using thermistor that can improve output ripple voltage according to temperature to improve. In case of high temperature where circuit is sensitive, it decides two comparable voltages high. And, in case of non-high temperature where circuit is stable, it decides two comparable voltages low, then it minimizes output ripple voltage. simulation result what is included in this paper describe that output ripple voltage is reduced more than 30mV by using suggested converter, and load regulation was 0.011mV/mA. Suggested circuit is suitable to power managing circuit that operate digital circuit requiring fast response and low power.

• Journal of IKEEE
• /
• v.14 no.3
• /
• pp.250-255
• /
• 2010

The interleaved power management IC(PMIC) with DTMOS(Dynamic Threshold voltage MOSFET) switching device is proposed in this paper. The buck-boost converter used to provide the high output voltage and low output voltage for portable applications. Also we used the PWM(Pulse Width Modulation) control method for high power efficiency at high current level. DTMOS with low on-resistance is designed to decrease conduction loss. The interleaved PMIC to reduce output ripple. And step-down DC-DC converter in stand-by mode below 1mA is designed with LDO in order to achive high efficiency.

• Journal of the Korean Solar Energy Society
• /
• v.34 no.2
• /
• pp.1-7
• /
• 2014

Generally, buck converter controller is designed to control the output voltage of the converter. However, design of the controller in a photovoltaic power conditioning system is different from theoretical design guideline. The controller in a photovoltaic power conditioning system controls the input voltage of the converter (the output voltage of the solar cell) to meet a maximum power point tracking (MPPT) performance. In this study, a new model for buck converter used in a photovoltaic power conditioning system is proposed, which is linearized after state-space averaging in each period. Also, mathematical expression of the modeled buck converter is interpreted separately as small and large signals; therefore its appropriateness is measured to design linear voltage and current controller.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.34 no.7A
• /
• pp.568-573
• /
• 2009

This paper presents a step-down DC-DC converter with On-chip Compensation for battery-operated portable electronic devices which are designed in O.13um CMOS standard process. In an effort to decrease system volume, this paper proposes the on chip compensation circuit using capacitor multiplier method. Capacitor multiplier method can minimize error amplifier's compensation capacitor size by 10%. It allows the compensation block of DC-DC converter be easily integrated on a chip and occupy less layout area. But capacitor multiplier operation reduces DC-DC converter efficiency. As a result, this converter shows maximum efficiency over 87.2% for the output voltage of 1.2V (input voltage : 3.3V), maximum load current 500mA, and 25mA output ripple current. This voltage mode controled buck converter has 1MHz switching frequency.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.11a
• /
• pp.377-382
• /
• 2009

modelling of the buck converter in photovoltaic power conditioning system is not a possibility of doing with input-output relationship from existing procedures. Because the input current and voltage of the buck converter in fluctuate at any time. The controller which design with the method which has like this error cannot have a good efficiency. In this paper, firstly, in order to design accurate controller of buck converter, new model is proposed. The modeling used a state-space averaging method and came to accomplish. Secondly, the process which design the controller is described. Finally, the simulation results are analyzed.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.2
• /
• pp.162-168
• /
• 2005

In this paper, a digital current mode control is designed for the power converter applications. The designed digital current mode controller is derived analytically from the continuous time small signal model of the power converters. Due to the small signal model based derivations of the control law, the designed control method can be applicable to boost, buck, and buck-boost converters. It is also proven that the controlled power converter employing the designed digital current mode controller is always stable regardless of an operating conditions. In order to show the usefulness of a designed controller, experiments are carried out using a 16bit DSP micro-processor, TMS320LF2406A.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.13 no.4
• /
• pp.311-318
• /
• 2008

This paper proposes synchronous bidirectional DC-DC converter applying soft-switching technique. The proposed converter integrates two advantages which are conduction loss minimization and switching loss elimination by applying interleaved synchronous buck and ZVT-cell with a single resonant inductor. ZVS is guaranteed for wide load range in CCM(Continuous Conduction Mode) as well as wide output voltage range by current injection method. Also, reverse recovery effects of body diode can be minimized. In addition, it is possible to significantly reduce diode drop voltage occurred during dead time of conventional synchronous buck converter. The validity of the proposed converter is verified through experimental results.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.5
• /
• pp.478-484
• /
• 2004

In this paper, two lossless snubber cells are proposed to generalize high frequency converter with losslless snubber. The selecting of snubber cells, which generalize high frequency converters, are depended on converter topologies. The cells have a saturable inductor, LC resonant tank and two diodes. In the cells, the saturable inductors extremely reduce resonant energy in the LC resonant tank. By minimizing resonant energy, the converter, which applies snubber cells, can operate at high frequency. These cells are applied for Buck, Boost, Buck-Boost, Cuk, ZETA, and SEPIC to generalize converter which have lossless snubber. The boost type converter has been implemented, with 400 kHz switching frequency for 125 W load to verify the converter characteristics.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.12 no.3
• /
• pp.241-247
• /
• 2007

This paper presents a new Leading edge modulation Buck converter operating in discontinuous conduction mode (DCM) for the pulse voltage input. In the slave output of the LLC half-bridge multi-resonant converter, to regulate the direct chopper's output voltage, its PWM switch is controlled by the leading edge modulation. The principles of this proposed LEM control method and the fast dynamics in inductor current based on the converter impulse response are studied. The theoretical results are verified through an experimental prototype of the 100W 60inch PDP Address power module.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.9
• /
• pp.21-26
• /
• 2016

This paper presents a step-down DC-DC buck converter with a CCM/DCM dual-mode function for the internal power stage of portable electronic device. The proposed converter that is operated with a high frequency of 1 MHz consists of a power stage and a control block. The power stage has a power MOS transistor, inductor, capacitor, and feedback resistors for the control loop. The control part has a pulse width modulation (PWM) block, error amplifier, ramp generator, and oscillator. In this paper, an external capacitor for compensation has been replaced with a multiplier equivalent CMOS circuit for area reduction of integrated circuits. In addition, the circuit includes protection block, such as over voltage protection (OVP), under voltage lock out (UVLO), and thermal shutdown (TSD) block. The proposed circuit was designed and verified using a $0.18{\mu}m$ CMOS process parameter by Cadence Spectra circuit design program. The SPICE simulation results showed a peak efficiency of 94.8 %, a ripple voltage of 3.29 mV ripple, and a 1.8 V output voltage with supply voltages ranging from 2.7 to 3.3 V.